display SAAB 9-2X 2006 Owners Manual

3-6
Instruments and controls
Hazard warning flasherThe hazard warning flasher is used to
warn other drivers when you have to park
your vehicle under emergency conditions.
The hazard warning flasher works with the
ignition switch in any position.
To turn on the hazard warning flasher,
push the hazard warning button on the in-
strument panel. To turn off the flasher,
push the button again.NOTEWhen the hazard warning flasher is on,
the turn signals do not work.
Meters and gaugesNOTELiquid-crystal displays are used in
some of the meters and gauges in the
combination meter. You will find their
indications hard to see if you wear po-
larized glasses.
SpeedometerThe speedometer shows the vehicle
speed.
Odometer/Trip meter1) Trip meter
2) OdometerThis meter displays the odometer and twotrip meters when the ignition switch is in
the “LOCK”, “ACC” or “ON” position.

Odometer
The odometer shows the total distance
that the vehicle has been driven.

Double trip meter
The trip meter shows the distance that the
vehicle has been driven since you last set
it to zero.
To change the mode indication, briefly
push the knob.
Each press of the knob changes the func-
tion alternately.
To set the trip meter to zero, select the A
300117
1
2
300614
300660
A trip meter B trip meter
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

5-6
Audio
Display
Control mode
Turn counterclockwise
Turn clockwise
BAS
Bass control
For less bass sound
For more bass sound
TRE
Treble control
For less treble sound
For more treble sound
BAL
Balance control
To increase left speaker volume and decrease right
speaker volume
To increase right speaker volume and decrease left
speaker volume
FAD
Fader control
To increase rear speaker volume and decrease front
speaker volume
To increase front speaker volume and decrease rear
speaker volume
VOL
Volume control
For less volume
For more volume
500009
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Audio
5-7
5
– CONTINUED –

FM/AM selection button (FM/AM)
Push the “FM/AM” button (4) when the ra-
dio is off to turn on the radio.
Push the “FM/AM” button when the radio
is on to select FM1, FM2 or AM reception.
Each time this button is pressed, the band
will change in the following order:
The display indicates which one is cur-
rently selected.

Stereo indicator
The stereo indicator “ST” will come on
when an FM stereo broadcast is received.

Manual tuning (TUNE)
Push the “
” side of the tuning button
(3) to increase the tuning frequency and
press the “” side of the button to de-
crease it.
Each time the button is pressed, the fre-
quency changes 10 KHz in the AM wave-
band and 0.2 MHz in the FM waveband.
Constant pressure on the button causes a
continuous change in the frequency.

Automatic tuning (SCAN)
Press the “SCAN” button (1) to change the
radio to the SCAN mode. In this mode, theradio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper-
ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.

Selecting preset stations
Presetting a station with a “Preset” button
(5) allows you to select that station in a
single operation. Up to six AM, FM1 and
FM2 stations each may be preset.

How to preset stations
1. Press the “FM/AM” selection button to
select AM, FM1 or FM2 reception.
2. Press the “SCAN” button (1) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the “Preset” buttons (5)
for at least 2 seconds to store the fre-
quency. The frequency of the station willflash once on the display at this time. If the
button is pressed for less than 2 seconds,
the preceding selection will remain in
memory.
NOTE
If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons.

If a cell phone is placed near the ra-
dio, it may cause the radio to emit
noise when it receives calls. This noise
does not indicate a radio fault.
FM1 FM2 AM
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

5-8
Audio

Compact disc player operation
500024
(7) (8)
(11) (10)(9)
(7) Eject button
(8) Disc slot
(9) DISC button
(10) Repeat/Random button
(11) Track selection buttons

To play back a compact disc
When CD is not in the player
Hold a disc with a finger in the center hole
while gripping the edge of the disc, then
insert it in to the slot (with the label side
up) and the player will automatically pull
the disc into position.
A single CD (8 cm/3 inch CD) may also be
used without any adapter.NOTE
Make sure to always insert a disc
with the label side up. If a disc is insert-
ed with the label side down, it might be
ejected or the player might shut off.

After the last song finishes, the play-
er will automatically return to track 1
(the first song on the disc).

CD-RWs cannot be used. Also, some
CD-Rs cannot be played.
When CD is in the player
Press the “DISC” button (9). The display
will show “CD” and the player will start
playback.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Audio
5-13
– CONTINUED –
5
Display
Control mode
Turn counterclockwise
Turn clockwise
BASS
Bass control
For less bass sound
For more bass sound
MIDDLE
Midrange control
For less midrange sound
For more midrange sound
TREBLE
Treble control
For less treble sound
For more treble sound
FADER
Fader control
To increase rear speaker volume and decrease front
speaker volume
To increase front speaker volume and decrease rear
speaker volume
BALANCE
Balance control
To increase left speaker volume and decrease right
speaker volume
To increase right speaker volume and decrease left
speaker volume
VOLUME
Volume control
For less volume
For more volume
500009
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

5-14
Audio
Tone control
The volume control dial (8) normally func-
tion as volume control. The dial becomes
a control for Bass, Midrange or Treble
when you select the appropriate tone con-
trol mode.
Choose desired level for each mode by
turning the volume control dial. The con-
trol function returns to volume control
mode after approximately 5 seconds.
To change control modes: Each brief
press of the “TONE” button (3) changes
control modes in the following sequence
starting from bass control mode. (When
the radio is first turned on, the control
mode is in the volume control.)
Fader and balance control
The volume control dial (8) normally func-
tion as volume control. The dial become
the controls for Fader or Balance when
you select the appropriate fader and bal-
ance control mode.
Choose desired setting for each mode by
turning the volume control dial. The con-
trol function returns to volume control
mode after approximately 5 seconds.To change control modes: Each brief
press of the “BAL” button (4) changes
control modes in the following sequence
starting from fader control mode. (When
the radio is turned on, the control mode is
in the volume control.)
Display illumination dimness can-
cellation (BRIGHT)
The brightness of the radio display dims
when the light switch is in the “
” or
“
” positions. If this makes the display
difficult to read, press the volume dial for
more than 1.5 seconds to return the dis-
play to original brightness.
Subsequently pressing the volume dial
again for more than 1.5 seconds or if you
can safely do so, turning the light switch to
the OFF position and back to the “
”
or “
” position makes the radio display
dim again.

FM/AM selection button
Push the “FM” (1) or “AM” (2) button when
the radio is off to turn on the radio.
Push the “FM” or “AM” button when the ra-
dio is on to select FM1, FM2 or AM recep-
tion.
Stereo indicator
The stereo indicator “ST” will come on
when an FM stereo broadcast is received.

Manual tuning (TUNE)
: Tuning to a higher frequency: Tuning to a lower frequency: Seeking the next higher station: Seeking the next lower station
Manual tuning
Turn the tuning knob (6) clockwise and re-
lease it immediately to increase the tuning
frequency and turn the tuning knob coun-
terclockwise and release it immediately to
decrease the tuning frequency.
Each time the knob is turned, the frequen-
cy changes 10 kHz in the AM waveband
and 0.2 MHz in the FM waveband.
VOLUME BASS TREBLEMIDDLE
FADER BALANCE VOLUME
500248
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Audio
5-15
5
– CONTINUED –
Seek tuning
Turn the tuning knob (6) and hold it for
more than a half second. Seek tuning will
operate and stop automatically on the
next station.
Continue this operation until you find the
desired station.

Automatic tuning (SCAN)
Press the “SCAN” button (5) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper-
ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.

Selecting preset stations
Presetting a station with a “Preset” button
(7) allows you to select that station in asingle operation. Up to six AM, FM1 and
FM2 stations each may be preset.

How to preset stations
1. Press the “FM/AM” selection button to
select AM, FM1 or FM2 reception.
2. Press the “SCAN” button (5) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the “Preset” buttons (7)
for at least 1.5 seconds to store the fre-
quency. The frequency of the station will
flash once on the display at this time. If the
button is pressed for less than 1.5 sec-
onds, the preceding selection will remain
in memory.
NOTE
If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons.

If a cell phone is placed near the ra-
dio, it may cause the radio to emit
noise when it receives calls. This noise
does not indicate a radio fault.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

5-16
Audio

Built in CD changer operation
(9)
(17) (16)(12) (11) (10) (13) (14) (15)
500249
(9) LOAD button
(10) Disc slot
(11) Repeat button
(12) Random button
(13) SCAN button
(14) CD button
(15) Eject button
(16) Fast-forwarding/Fast-reversing and
track UP/DOWN knob
(17) Disc select buttonNOTE
Make sure to always insert a disc
with the label side up. If a disc is insert-
ed with the label side down, it might be
ejected or the player might shut off.

Certain CD-Rs and CD-RWs cannot
be played.

How to insert a CD(s)
Inserting a CD
1. Press “LOAD” button (9). If the maga-
zine in the player has an open position
where you can insert a disc, the “DISC” in-
dicator associated with the open position
will blink. The capacity is 6 discs.
If no indicator blinks, it means that there is
no open position in the magazine.
2. As soon as the “DISC” indicator begins
to blink, the “LOAD” will appear on display
for a period of 15 seconds. Insert a disc
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Audio
5-17
5
– CONTINUED –
during the period. The disc will be then au-
tomatically drawn in, and the player will
begin to play back the first track of the
disc.

To insert more discs in succession, re-
peat Steps 1 and 2. The magazine will be
loaded with discs in the ascending order
of position number.
If you do not insert any disc in 15 seconds
after you have pressed the “LOAD” but-
ton, the player will begin to play back the
first track of the last disc you have insert-
ed.

The disc indicator steadily lights up if a
disc is already inserted in the correspond-
ing position of the magazine.

While the player is in the loading mode,
if you press any of the other mode buttons
“FM” (1), “AM” (2), the player will enter the
standby mode. Press the “CD” button (14)
to start playback.
Inserting a disc in a desired position
1. Press the “LOAD” button (9). If the
magazine in the player has an open posi-
tion where you can insert a disc, the
“DISC” indicator associated with the open
position will blink.
The positions in the magazine the indica-
tor of which steadily lights up are already
loaded with discs.
2. Press the “Disc select” button (17) atthe position where you want to insert a
disc. The associated “DISC” indicator will
blink, and the “LOAD” will be displayed.
3. If you insert a disc during the 15-sec-
ond period while the “LOAD” is on display,
the disc will be automatically drawn in,
and the player will start playback of the
disc, beginning with the first track.

To insert more discs in succession, re-
peat Steps 1 and 2.

While the player is in the loading mode,
if you press any of the other mode buttons
“FM” (1), “AM” (2), the player will enter
standby mode. Press the “CD” button (14)
to start playback.
Loading the magazine (Full disc
loading mode)
1. If you continue to press the “LOAD”
button (9) for more than 1.5 seconds, the
player will produce a beeping sound and
will enter the full disc loading mode.
2. A “DISC” indicator will blink, and the
“ALL LOAD” will be on display for a period
of 15 seconds. If a disc is successfully
loaded during this period, the “DISC” indi-
cator will stop blinking and will steadily
light.
3. When the loading of a disc is complete,
the next “DISC” indicator will blink. Then
repeat Step 2.
4. When the magazine is filled with discsby repeating Steps 2 and 3, the player will
start playback of the discs, beginning with
the one inserted first.
If you fail to insert any disc during each 15
seconds interval, the full disc loading
mode will be canceled, and the player will
start playback of the disc inserted first.

How to play back a CD or make a
pause
When there is no CD inserted:
Insert a CD by referring to “How to Insert
a CD(s)”.
When a CD is loaded, the player will start
playback of the CD, beginning with the
first track.
When there are CDs loaded:
Press a desired one of the “Disc select”
buttons (17) the “DISC” indicator of which
steadily lights up. The player will then start
playback of the selected CD, beginning
with the first track.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 11
11
– CONTINUED –

Recommended grade and
viscosityOil grade:
ILSAC GF-4, which can be identified
with the ILSAC certification mark
(Starburst mark)
or API classification SM with the
words “ENERGY CONSERVING”
These recommended oil grades can be
identified by looking for either or both of
the following marks displayed on the oil
container.API Service label
1) Indicates the oil quality by API designa-
tions
2) Indicates the SAE oil viscosity no.
3) Indicates that the oil has fuel saving ca-
pabilitiesILSAC
Certification Mark (Starburst
Mark)
In choosing an oil, you want the proper
quality and viscosity, as well as one that
will add to fuel economy. The following ta-
ble lists the recommended viscosities and
applicable temperatures.
When adding oil, different brands may be
used together as long as they are the
same API classification and SAE viscosity
as those recommended by Saab.
SAE viscosity no. and applicable tem-
perature
*: 5W-30 is recommended.Engine oil viscosity (thickness) affects fuel
economy. Oils of lower viscosity provide
better fuel economy. However, in hot
weather, oil of higher viscosity is required
to properly lubricate the engine.
Recommended grade and
viscosity under severe driv-
ing conditionsIf the vehicle is used in desert areas, in ar-
APISERVICE
SM
ENERGY
CONSERVING
SAE
5W-30
1
2
3
B00446
B00014
Use only engine oil with the recom-
mended grade and viscosity.
B00522
5W-30*
10W-30, 10W-40 -30 -20 -10 0 10 20 30 40
-20 0 6020 80 10040
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com