engine oil SAAB 9-2X 2006 Owners Manual
[x] Cancel search | Manufacturer: SAAB, Model Year: 2006, Model line: 9-2X, Model: SAAB 9-2X 2006Pages: 322, PDF Size: 11.42 MB
Page 3 of 322
Fuel octane ratingThis octane rating is the average of the Research Octane and Motor
Octane numbers and is commonly referred to as the Anti Knock
Index (AKI). Refer to “Fuel” section in this manual.Fuel capacity15.9 US gal (60 liters, 13.2 Imp gal)Engine oilUse only API classification SM with the words “ENERGY CON-
SERVING” and the ILSAC certification mark (starburst mark) dis-
played on the container.Engine oil capacity4.2 US qt (4.0 liters, 3.5 Imp qt)
Gas station referenceFuel• 2.5-liter non-turbo models
Use only unleaded gasoline with an octane rating of 87 AKI or
higher.
• 2.5-liter turbo models (Aero)
Use premium unleaded gasoline with an octane rating of 91 AKI or
higher. If premium unleaded gasoline is not available, regular
unleaded gasoline with octane rating of 87 AKI or higher may be
temporarily used. For optimum engine performance and driveabil-
ity, it is required that you use premium grade unleaded gasoline.Cold tire pressureNOTE:
Adjust the tire pressure to 36 psi (250 kPa, 2.5 kgf/cm
2) when driving the vehicle with five people and cargo inside and at speeds
exceeding 99.4 mph (160 km/h).Tire size P205/55R16 89V 215/45R17 91W
Wheel size 16 x 61/2 JJ 17 x 7 JJ
Pressure Front
32 psi (220 kPa, 2.2 kgf/cm
2) 33 psi (230 kPa, 2.3 kgf/cm
2)
Rear
29 psi (200 kPa, 2.0 kgf/cm
2) 32 psi (220 kPa, 2.2 kgf/cm
2)
Temporary spare tire Size T135/70 D16
Pressure
60 psi (420 kPa, 4.2 kgf/cm
2)
9-2XUScoverM06.fm Page 3 Friday, September 9, 2005 1:48 PM
ProCarManuals.com
Page 9 of 322
3
Vehicle symbolsThere are some of the symbols you may
see on your vehicle.
Symbol Name
CAUTIONPower door lock and unlockPassenger’s windows lock
and unlockFuelFront fog lightsParking lightsHazard warning flasherCigarette lighterEngine hoodSeat heater
Child restraint top tether an-
choragesChild restraint lower anchor-
agesHornWindshield wiper deicerWiper intermittentWindshield wiper and wash-
erRear window wiper and
washerLightsParking lights, tail lights, li-
cense plate light and instru-
ment panel illuminationHead lightsIllumination brightness Symbol Name
Fan speedInstrument panel outletsInstrument panel outlets and
foot outletsFoot outletsWindshield defroster and
foot outletsWindshield defrosterRear window defogger/Out-
side mirror defoggerAir recirculationOutside airEngine oilWasherDoor lock (transmitter) Symbol Name
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 23 of 322
17
– CONTINUED –
Warning and indicator lightSymbol Name Page
Seatbelt warning light 3-9SRS airbag system
warning light3-10Passenger airbag ON
indicator light3-10Passenger airbag OFF
indicator light3-10CHECK ENGINE
warning light/Malfunc-
tion indicator lamp3-11Charge warning light 3-11Oil pressure warning
light3-11Automatic transmis-
sion Oil temperature
warning light 33-12
or
ABS warning light 3-12
or
Brake system warning
light3-13
ON orOFF or
Door open warning
light3-13All-Wheel Drive warn-
ing light (AT) 3
3-14
Turn signal indicator
lights3-14High beam indicator
light3-14Security system indi-
cator light2-7Cruise control indica-
tor light3-14Cruise control set indi-
cator light3-15 Symbol Name Page
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 103 of 322
13
Instruments and controls
Ignition switch .................................................... 3-3
LOCK ....................................................................... 3-3
ACC .......................................................................... 3-4
ON ............................................................................ 3-4
START ...................................................................... 3-4
Key reminder chime ............................................... 3-5
Ignition switch light 3 ............................................ 3-5
Key interlock release (AT vehicles only) .............. 3-5
Hazard warning flasher ...................................... 3-6
Meters and gauges ............................................. 3-6
Speedometer ........................................................... 3-6
Odometer/Trip meter .............................................. 3-6
Tachometer ............................................................. 3-7
Fuel gauge ............................................................... 3-7
Temperature gauge ................................................ 3-8
Outside temperature indicator .............................. 3-9
Warning and indicator lights ............................. 3-8
Seatbelt warning light and chime .......................... 3-9
SRS airbag system warning light .......................... 3-10
Front passenger’s frontal airbag ON and OFF
indicators .............................................................. 3-10
CHECK ENGINE warning light/Malfunction
indicator lamp ....................................................... 3-11
Charge warning light .............................................. 3-11
Oil pressure warning light ..................................... 3-11
AT OIL TEMPerature warning light
(AT vehicles) ......................................................... 3-12
ABS warning light ................................................... 3-12
Brake system warning light ................................... 3-13Door open warning light ........................................ 3-13
All-Wheel Drive warning light (AWD AT
vehicles) ................................................................ 3-14
Selector lever position indicator (AT
vehicles) ................................................................ 3-14
Turn signal indicator lights .................................... 3-14
High beam indicator light ....................................... 3-14
Cruise control indicator light ................................. 3-14
Cruise control set indicator light .......................... 3-15
Clock .................................................................... 3-15
Light control switch ........................................... 3-15
Headlights ............................................................... 3-16
High/low beam change (dimmer) .......................... 3-16
Headlight flasher ..................................................... 3-16
Daytime running light system ............................... 3-17
Turn signal lever ................................................. 3-17
Illumination brightness control ......................... 3-18
Headlight beam leveler (Cars with HID
headlights only) ............................................... 3-18
Parking light switch ........................................... 3-19
Front fog light button
3 ..................................... 3-19
Wiper and washer ............................................... 3-20
Windshield wiper and washer switches ............... 3-21
Rear window wiper and washer switch ................ 3-22
Rear window defogger button ........................... 3-23
Windshield wiper deicer
3 ................................. 3-24
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 111 of 322
Instruments and controls
3-9
3
– CONTINUED –
Warning and indicator lightsSeveral of the warning and indicator lights
come on momentarily and then go out
when the ignition switch is initially turned
to the “ON” position. This permits check-
ing the operation of the bulbs.
Apply the parking brake and turn the igni-
tion switch to the “ON” position. The fol-
lowing lights come on:
Seatbelt warning light
SRS airbag system warning light
Front passenger’s frontal airbag ON in-
dicator light
Front passenger’s frontal airbag OFF
indicator light
CHECK ENGINE warning light/Mal-
function indicator lamp
Charge warning light
Oil pressure warning light
AT OIL temperature warning light (AT
vehicles)
ABS warning light
Brake system warning light
All-Wheel Drive warning light (AWD AT
vehicles)
Cruise control indicator light 3
Cruise control set indicator light 3
If any lights fail to come on, it indicates a
burned-out bulb or a malfunction of the
corresponding system.Consult your authorized Saab dealer for
repair.
Seatbelt warning light
and chimeYour vehicle is equipped with a seatbelt
warning device at the driver’s seat, as re-
quired by current safety standards. There
is a seatbelt warning light in the combina-
tion meter.
If the driver has not yet fastened the seat-
belt when the ignition switch is turned to
the “ON” position, the seatbelt warning
light will flash for 6 seconds, to warn that
the seatbelt is unfastened. If the driver’s
seatbelt is not fastened, a chime will also
sound simultaneously.
If the driver’s seatbelt is still not fastened
6 seconds later, the warning light will re-
main lit for 15 seconds. If the driver’s seat-
belt is still not fastened even 15 seconds
later (21 seconds after turning ON the ig-
nition switch), the warning lights will alter-
nate between flashing and steady illumi-
nation at 15-second intervals, and the
chime will sound while the warning light is
flashing.
Alternate flashing and steady illumination
of the warning lights and sounding of the
chime will continue until the driver fastens
the seatbelt.
NOTEIf the driver unfastens the seatbelt af-
ter fastening, the seatbelt warning de-
vice operates as follows according to
the vehicle speed.
At speeds lower than approximate-
ly 9 mph (15 km/h)
The warning light will alternate be-
tween flashing and steady illumina-
tion at 15-second intervals. The
chime will not sound.
At speeds higher than approxi-
mately 9 mph (15 km/h)
The warning light will alternate be-
tween flashing and steady illumina-
tion at 15-second intervals and the
chime will sound while the warning
light is flashing.
It is possible to cancel the warning
operation that follows the 6-second
warning after turning ON the ignition
switch by unfastening and refastening
the driver’s seatbelt. When the ignition
switch is turned ON next time, howev-
er, the complete sequence of warning
operation resumes. For further details
about canceling the warning operation,
please contact your Saab dealer.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 113 of 322
Instruments and controls
3-11
3
– CONTINUED –
CHECK ENGINE warn-
ing light/Malfunction in-
dicator lampIf this light comes on steadily or blinks
while the engine is running, it may indicate
that there is a problem or potential prob-
lem somewhere in the emission control
system.
If the light comes on steadily:
If the light comes on steadily while driving
or does not go out after the engine starts,
an emission control system malfunction
has been detected.
You should have your vehicle checked by
an authorized Saab dealer immediately.NOTEThis light also comes on when the fuelfiller cap is not tightened until it clicks.
If you have recently refueled your vehicle,
the cause of the CHECK ENGINE warning
light/malfunction indicator lamp coming on
could be a loose or missing fuel filler cap.
Remove the cap and retighten it until it
clicks. Make sure nothing is interfering
with the sealing of the cap. Tightening the
cap will not make the CHECK ENGINE
warning light turn off immediately. It may
take several driving trips. If the light does
not go out, take your vehicle to your au-
thorized Saab dealer immediately.
If the light is blinking:
If the light is blinking while driving, an en-
gine misfire condition has been detected
which may damage the emission control
system.
To prevent serious damage to the emis-
sion control system, you should do the fol-
lowing.
Reduce vehicle speed.
Avoid hard acceleration.
Avoid steep uphill grades.
Reduce the amount of cargo, if possi-
ble.
Stop towing a trailer as soon as pos-
sible.
The CHECK ENGINE warning light may
stop blinking and come on steadily afterseveral driving trips. You should have
your vehicle checked by an authorized
Saab dealer immediately.
Charge warning light If this light comes on when the engine is
running, it may indicate that the charging
system is not working properly.
If the light comes on while driving or does
not go out after the engine starts, stop the
engine at the first safe opportunity and
check the alternator belt. If the belt is
loose, broken or if the belt is in good con-
dition but the light remains on, contact
your nearest Saab dealer immediately.Oil pressure warning
lightIf this light comes on when the engine is
running, it may indicate that the engine oil
pressure is low and the lubricating system
is not working properly.
If the light comes on while driving or does
not go out after the engine starts, stop the
engine at the first safe opportunity and
check the engine oil level. If the oil level is
low, add oil immediately. If the engine oil
is at the proper level but the light remains
on, contact your nearest Saab dealer im-
mediately. If the CHECK ENGINE light comes
on while you are driving, have your
vehicle checked/repaired by your
Saab dealer as soon as possible.
Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could cause serious damage, which
may not be covered by your vehi-
cle’s warranty.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 114 of 322
3-12
Instruments and controls
AT OIL TEMPerature
warning light (AT vehi-
cles)The AT oil temperature warning light
comes on when the ignition switch is
turned to the “ON” position and goes out
after approximately two seconds.
If this light comes on when the engine is
running, it may indicate that the automatic
transmission fluid temperature is too hot.
If the light comes on while driving, it is un-
necessary to stop the vehicle, but avoid
driving up steep grades or in stop and go
traffic.
Automatic transmission control
system warning
If the light flashes after the engine starts,
it may indicate that the automatic trans-
mission control system is not working
properly. Contact your nearest Saab deal-
er for service immediately.
ABS warning light The ABS warning light comes on when the
ignition switch is turned to the “ON” posi-
tion and goes out after approximately two
seconds.
This is an indication that the ABS system
is working properly.
With a vehicle equipped with an Electronic
Brake Force Distribution (EBD) system,
the ABS warning light comes on together
with the brake system warning light if the
EBD system becomes faulty. For further
details of the EBD system fault warning,
refer to “Brake system warning light”.NOTEIf the warning light behavior is as de-
scribed in the following, the ABS sys-
tem may be considered normal.
The warning light comes on right af-
ter the engine is started but goes out
immediately, remaining off.
The warning light remains on after
the engine has been started, but it goes
out when the vehicle speed reaches
approximately 8 mph (12 km/h).
The warning light comes on during
driving, but it goes out immediately
and remains off.
When driving with an insufficient battery
voltage such as when the engine is jump
started, the ABS warning light may come
on. This is due to the low battery voltage
and does not indicate a malfunction. Do not operate the engine with the
oil pressure warning light on. This
may cause serious engine damage.
When the warning light is on, the
ABS function shuts down; however,
the conentional brake system con-
tinues to operate normally.
If the warning light behaves as fol-
lows, the ABS system may not work
properly.
The warning light does not come
on when the ignition switch is
turned to the “ON” position.
The warning light comes on when
the ignition switch is turned to the
“ON” position, but it does not go
out even when the vehicle speed
exceeds approximately 8 mph (12
km/h).
The warning light comes on dur-
ing driving.
(U.S.)
(Canada)
If any of these conditions occur,
have the ABS system repaired at the
first available opportunity by your
Saab dealer.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 129 of 322
14
Climate control
Ventilation ........................................................... 4-2
Air flow selection .................................................... 4-2
Center and side vents ............................................ 4-3
Manual climate control system
3 ..................... 4-3
Control panel .......................................................... 4-3
Heater operation ..................................................... 4-5
Air conditioner operation ....................................... 4-7
Automatic climate control system
3 ............... 4-7
Control panel .......................................................... 4-8
To use as full-automatic climate control
system ................................................................... 4-8
To use as semi-automatic climate control
system ................................................................... 4-8
Fan speed control dial ........................................... 4-8
Temperature control dial ........................................ 4-9
Air flow control dial ................................................ 4-9
Air inlet selection button ........................................ 4-9
Air conditioner button ............................................ 4-10
Temperature sensors ............................................. 4-10
Operating tips for heater and air
conditioner ...................................................... 4-11
Cleaning ventilation grille ...................................... 4-11
Efficient cooling after parking in direct
sunlight ................................................................. 4-11
Lubrication oil circulation in the refrigerant
circuit .................................................................... 4-11
Checking air conditioning system before
summer season .................................................... 4-11
Cooling and dehumidifying in high humidity
and low temperature weather conditions .......... 4-11Air conditioner compressor shut-off when
engine is heavily loaded ...................................... 4-12
Refrigerant for your climate control system ........ 4-12
Air filtration system
3 ........................................ 4-12
Replacing an air filter ............................................. 4-12
3 Asterisk means: equipment not fitted in all cars (can depend
on model variant, engine variant, market specification, options
or accessories)
.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 139 of 322
Climate control
4-11
4
– CONTINUED –
– Do not subject the sensors to impact.
– Keep water away from the sensors.
– Do not cover the sensors.
The sensors are located as follows:
– Solar sensor: beside windshield de-
froster grille
– Interior air temperature sensor: beside
the fan speed control dial
– Outside temperature sensor: behind
front grille.
Operating tips for heater and air conditionerCleaning ventilation grilleAlways keep the front ventilation inlet
grille free of snow, leaves, or other ob-
structions to ensure efficient heating and
defrosting. Since the condenser is located
in front of the radiator, this area should be
kept clean because cooling performance
is impaired by any accumulation of insects
and leaves on the condenser.Efficient cooling after parking
in direct sunlightAfter parking in direct sunlight, drive with
the windows open for a few minutes to al-low outside air to circulate into the heated
interior. This results in quicker cooling by
the air conditioner. Keep the windows
closed during the operation of the air con-
ditioner for maximum cooling efficiency.
Lubrication oil circulation in
the refrigerant circuitOperate the air conditioner compressor at
a low engine speed (at idle or low driving
speeds) a few minutes each month during
the off-season to circulate its oil.Checking air conditioning
system before summer sea-
sonCheck the air conditioner unit for refriger-
ant leaks, hose conditions, and proper op-
eration each spring. This check is best
performed by your Saab dealer.Cooling and dehumidifying in
high humidity and low tem-
perature weather conditionsUnder certain weather conditions (high
relative humidity, low temperatures, etc.)
a small amount of water vapor emission
from the air outlets may be noticed. This
condition is normal and does not indicate
400610
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com
Page 178 of 322
7-6
Starting and operating
A vehicle fails
the OBD inspection if the
“CHECK ENGINE” warning light/MIL is
not properly operating or there is one or
more diagnostic trouble codes stored in
vehicle’s computer with the “CHECK EN-
GINE” warning light/MIL illuminated.
A state emission inspection may reject
(not pass or fail) a vehicle if the number of
OBD system readiness monitors “Not
Ready” is greater than one. Under this
condition, the vehicle operator should be
instructed to drive his/her vehicle for a few
days to set the monitors and return for an
emission re-inspection.
Owners of rejected or failing vehicles
should contact their Saab Dealer for ser-
vice.
Preparing to driveYou should perform the following checks
and adjustments every day before you
start driving.
1. Check that all windows, mirrors, and
lights are clean and unobstructed.
2. Check the appearance and condition of
the tires. Also check tires for proper infla-
tion.
3. Look under the vehicle for any sign of
leaks.
4. Check that the hood, trunk and rear lift-
gate are fully closed.
5. Check the adjustment of the seat.
6. Check the adjustment of the inside and
outside mirrors.
7. Fasten your seatbelt. Check that your
passengers have fastened their seatbelts.
8. Check the operation of the warning and
indicator lights when the ignition switch is
turned to the “ON” position.
9. Check the gauges, indicator and warn-
ing lights after starting the engine.NOTEEngine oil, engine coolant, brake fluid,
washer fluid and other fluid levels
should be checked daily, weekly or at
fuel stops.
Starting the engineManual transmission vehicle1. Apply the parking brake.
2. Turn off unnecessary lights and acces-
sories.
3. Press the clutch pedal to the floor and
shift the shift lever into neutral. Hold the
clutch pedal to the floor while starting the
engine.
The starter motor will only operate when
the clutch pedal is pressed fully to the
floor.
4. Turn the ignition switch to the “ON” po-
sition and check the operation of the warn-
ing and indicator lights. Refer to the
“Warning and indicator lights” section
(chapter 3).
5. Turn the ignition switch to the “START”
position without depressing the accelera-
tor pedal. Release the key immediately af-
ter the engine has started.Do not operate the starter motor
continuously for more than ten sec-
onds. If the engine fails to start after
operating the starter for five to ten
seconds, wait for ten seconds or
more before trying again.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com