display SATURN AURA HYBRID 2007 Owners Manual

Matching Transmitter(s) to Your
Vehicle
Each RKE transmitter is coded to prevent another
transmitter from unlocking your vehicle. If a
transmitter is lost or stolen, a replacement can be
purchased through your retailer. Remember to
bring any remaining transmitters with you
when you go to your retailer. Each vehicle can
have a maximum of four transmitters matched to it.
Battery Replacement
Under normal use, the battery in your RKE
transmitter should last about four years.
The battery is weak if the transmitter does not work
at the normal range in any location. If you have to
get close to your vehicle before the transmitter
works, it is probably time to change the battery.
If the battery is low, a KEY FOB BATT (Battery)
LOW message will display in the vehicle’s DIC.
Notice:When replacing the battery, use
care not to touch any of the circuitry. Static
from your body transferred to these surfaces
may damage the transmitter.To replace the battery in the RKE transmitter do
the following:
1. Insert a at object, with a thin edge, into the
notch located below the vehicle locator/panic
alarm button, and separate the bottom
half from the top half of the transmitter.
2. Remove the battery and replace it with the
new one. Make sure the positive (+) side of
the battery faces up. Use one three-volt,
CR2032, or equivalent, type battery.
92

Power Door Locks
The power door lock switches are located on the
driver’s and front passenger’s door.
Press the outboard side of the switch to unlock all
doors. Press the inboard side of the switch to
lock all doors.
The rear doors do not have power door lock
switches. Rear seat passengers must use
the manual lock knob on their doors.
Door Ajar Reminder
If one of the doors is not fully closed while the
ignition is on and the shift lever is moved out of
PARK (P) or NEUTRAL (N) the following will occur:
A chime will sound.
The DOOR AJAR message will display
through the Driver Information Center (DIC)
until the door is closed. SeeDIC Warnings and
Messages on page 182.
Delayed Locking
This feature allows the driver to delay the locking
of the vehicle. It will not operate with the key
in the ignition. SeeLockout Protection on page 97.
Press the driver’s power door lock switch or the
Remote Keyless Entry (RKE) transmitter lock
button once. With the key removed from the
ignition and the driver’s door open, the following
occurs:
Three chimes sound to signal the delay.
All doors will lock and the turn signals ash
once ve seconds after the last door has
been closed.
The horn chirps if the horn chirp feature is
enabled. SeeDIC Vehicle Personalization
on page 187.
If a door is opened before the ve seconds has
elapsed, the doors do not lock until ve seconds
after all doors are closed.
If the power door lock switch or the transmitter
lock button is pressed twice when leaving
the vehicle, the doors lock immediately.
94

If the power door unlock switch or the transmitter
unlock button is pressed, the doors unlock
immediately and do not lock automatically after
the doors are closed.
This feature is turned on at the factory but may
be turned off through the Driver Information
Center (DIC). SeeDIC Vehicle Personalization
on page 187
Programmable Automatic Door
Locks
Your vehicle is programmed at the factory to lock all
doors automatically when the following are met:
All doors are closed.
The ignition is on.
The shift lever is moved out of PARK (P).
This feature cannot be disabled.When the shift lever is moved back to PARK (P),
all doors will unlock.
If someone needs to exit the vehicle once the
doors are locked, have that person use the manual
lock knob or power door unlock switch.
The power door unlock function can be
programmed through prompts displayed on the
Driver Information Center (DIC). These prompts
allow you to choose unlock settings. SeeDIC
Vehicle Personalization on page 187.
95

Ignition Positions
With the key in the
ignition switch, you can
turn it to four different
positions.
Notice:Using a tool to force the key from the
ignition switch could cause damage or
break the key. Use the correct key and turn the
key only with your hand. Make sure the key
is in all the way. If none of this works,
then your vehicle needs service.
9(OFF):This is the only position from which
you can remove the key. It also locks the ignition
and transaxle. A warning chime sounds if the
driver’s door is opened while the ignition is off and
the key is left in the ignition.ACC (ACCESSORY):This position lets you use
things like the radio and windshield wipers
while the engine is not running.
Use this position if your vehicle must be pushed or
towed, but never try to push-start your vehicle.
SeeRecreational Vehicle Towing on page 247.
R(ON):This position unlocks the ignition. It
is also the position to where the key returns after
you release the switch and the engine starts.
The switch will stay in this position while the
engine is running. But even while the engine is not
running, you can use ON to operate the electrical
accessories, and to display some instrument
panel warning lights.
The battery could be drained if you leave the key
in the ACC or ON position with the engine off.
You might not be able to start your vehicle if the
battery is allowed to drain for an extended
period of time.
/(START):This position starts the engine.
When the engine starts, release the key.
The ignition switch will return to the ON position
for normal driving.
108

Engine Coolant Temperature
Warning Light........................................ 171
Malfunction Indicator Lamp........................ 172
Oil Pressure Light..................................... 175
Security Light............................................ 176
Cruise Control Light.................................. 176
Highbeam On Light................................... 176
Fuel Gage................................................. 177
Auto Stop Mode........................................ 178
Charge/Assist Gage................................... 178
Fuel Economy Light.................................. 179
Driver Information Center (DIC).................. 179
DIC Operation and Displays...................... 180
DIC Warnings and Messages.................... 182
DIC Vehicle Personalization....................... 187Audio System(s)......................................... 192
Setting the Time........................................ 194
Radio with CD (MP3)................................ 195
Using an MP3........................................... 200
Theft-Deterrent Feature............................. 206
Audio Steering Wheel Controls.................. 206
Radio Reception........................................ 207
Care of Your CDs..................................... 207
Care of the CD Player.............................. 207
Backglass Antenna.................................... 208
Section 3 Instrument Panel
136

RES+ (Resume):Press RES+ to resume a set
speed and to accelerate the speed.
SET−(Set):Press SET– to set a speed and to
decrease the speed.
To set a speed do the following:
1. Press
Ito turn cruise control on. The
indicator light on the button comes on.
2. Get up to the desired speed.
3. Press the SET−and release it. The cruise
symbol displays in the instrument panel
cluster to show the system is engaged.
4. Take your foot off the accelerator pedal.
When the brakes are applied, the cruise control
shuts off.
If the vehicle is in cruise control and the Traction
Control System (TCS) begins to limit wheel
spin, the cruise control automatically disengages.
SeeTraction Control System (TCS) on page 217.
When road conditions allow, the cruise control
can be used again.
Resuming a Set Speed
Suppose you set the cruise control at a desired
speed and then apply the brakes. This disengages
the cruise control. The cruise symbol in the
instrument panel cluster also goes out indicating
cruise is no longer engaged. To return to the
previously set speed, you do not need to
go through the set process again. Once the
vehicle is at a speed of about 25 mph (40 km/h) or
more, you can briey press the RES+.
This takes the vehicle back up to the previously
chosen speed and stays there.
Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed.
If the cruise control system is already
engaged, press the RES+. Hold it there until
you reach the desired speed, and then release
the button.
To increase the vehicle’s speed in very small
amounts, briey press the RES+ and then
release it. Each time this is done, the vehicle
goes about 1 mph (1.6 km/h) faster.
146

Parade Dimming
Parade dimming is a separate lighting mode that
comes on while the parking lamps are turned
on during the day. It prevents the display lights and
indicator lights from being dim, while the parking
lamps are used during the day.
Overhead Console Reading Lamps
The vehicle may have reading lamps on the
overhead console. These lamps come on when
the doors are opened if the lamp switch is
not in the OFF position. Press the side of each
lamp to turn them on and off, while the doors are
closed.
Overhead Ambient Lighting
These lamps will automatically turn on and off as
controlled by the light sensor located on top of
the instrument panel.
Trunk Lamp
The trunk lamp comes on when the trunk is open
and turns off when it is closed.
Battery Run-Down Protection
Your vehicle has a battery run-down feature
designed to protect the vehicle’s battery.
When any interior lamp (trunk, reading lamps, or
dome lamp) is left on when the ignition is
turned off, the battery run-down protection system
automatically shuts the lamp off after 20 minutes.
This prevents draining of the battery.
To reactivate the interior lamps, do one of the
following:
Open any door.
Press any Remote Keyless Entry (RKE)
transmitter button.
Press the power door lock switch.
Press the remote trunk release.
Turn the lamp that was left on to off and then
to on again.
152

Automatic Operation
AUTO (Automatic):Select AUTO on both the fan
speed knob and the air delivery mode knob to
activate the automatic system. When automatic
operation is active the system controls the
inside temperature and air delivery.
Use the steps below to place the entire system in
full automatic control:
1. Turn the fan knob and the mode knob to the
AUTO position.
The current set temperature displays. When
AUTO is selected, the air conditioning
operation and air inlet is automatically
controlled. The air conditioning compressor
runs while the outside temperature is
over about 40°F (4°C). The air inlet is normally
set to outside air. If it is hot outside, the air
inlet can automatically switch to recirculate
inside air to help quickly cool down your
vehicle.
2. Set the temperature.
An initial setting of 73°F (23°C) is
recommended. Allow about 20 minutes for the
system to regulate. Press the
worxarrow
temperature buttons to adjust the temperaturesetting as necessary. If the temperature is set
at 60°F (15°C) the system remains at the
maximum cooling setting. If the temperature is
set at 90°F (32°C) the system remains at the
maximum heat setting. Choosing either
maximum setting does not cause the vehicle to
heat or cool any faster.
Be careful not to cover the sensor located on
the top of the instrument panel near the
windshield. This sensor regulates air
temperature based on the intensity of the sun.
Also do not cover the sensor grille on the
lower right side of the climate control
faceplate, as this regulates the inside
temperature.
To avoid blowing cold air at engine start-up in
cold weather, the system delays turning on
the fan until warm air is available. The length
of delay depends on the engine coolant
temperature. Turning the fan knob overrides
this delay and changes the fan to the selected
speed.
155

Speedometer and Odometer
Your speedometer lets you see your speed in
miles per hour (mph) or kilometers per hour (km/h).
SeeDIC Vehicle Personalization on page 187
for more information.
Your odometer shows how far your vehicle has
been driven, in either miles (used in the United
States) or kilometers (used in Canada).
Your vehicle has a tamper resistant odometer.
The digital odometer will read 999,999 if someone
tries to turn it back.
You may wonder what happens if your vehicle
needs a new odometer installed. If the new
one can be set to the mileage total of the old
odometer, then it must be. But if it can’t, then it is
set at zero and a label must be put on the
driver’s door to show the old mileage reading
when the new odometer was installed.
Trip Odometer
The trip odometer can tell you how far you have
driven since you last reset it.
The trip odometer is accessed and reset through
the Driver Information Center (DIC). SeeDIC
Operation and Displays on page 180for more
information.
Tachometer
Your tachometer displays the engine speed in
revolutions per minute (rpm).
Your vehicle has auto stop and the indicator for
this is on the tachometer. For more information see
Auto Stop Mode on page 178.
Safety Belt Reminder Light
When the key is turned to ON or START, a chime
will come on for several seconds to remind
people to fasten their safety belts, unless the
driver’s safety belt is already buckled.
The safety belt light will
also come on and stay
on for several
seconds, then it will
ash for several more.
This chime and light is repeated if the driver
remains unbuckled and the vehicle is in motion.
If the driver’s belt is already buckled, neither
the chime nor the light will come on.
163

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided
into two parts. If one part is not working, the other
part can still work and stop you. For good
braking, though, you need both parts working well.
If the warning light comes on, there is a brake
problem. Have your brake system inspected
right away.
This light should come on briey when you turn
the ignition key to ON. If it does not come on then,
have it xed so it will be ready to warn you if
there is a problem.When the ignition is on, the brake system warning
light will also come on when you set your
parking brake. The light will stay on if your parking
brake does not release fully. If it stays on after
your parking brake is fully released, it means you
have a brake problem.
The Driver Information Center (DIC) may display a
BRAKE FLUID message. SeeDIC Warnings
and Messages on page 182for more information.
If the light comes on while you are driving, pull
off the road and stop carefully. You may notice that
the pedal is harder to push or the pedal may go
closer to the oor. It may take longer to stop.
Try turning off and restarting the vehicle one or two
times, if the light is still on, have the vehicle
towed for service. SeeTowing Your Vehicle on
page 247.
United StatesCanada
168