SATURN ION 2006 Owners Manual

{CAUTION:
Using a match near a battery can cause battery
gas to explode. People have been hurt doing
this, and some have been blinded. Use a
ashlight if you need more light.
Be sure the battery has enough water. You do
not need to add water to the battery installed
in your new vehicle. But if a battery has ller
caps, be sure the right amount of uid is there.
If it is low, add water to take care of that rst.
If you do not, explosive gas could be present.
Battery uid contains acid that can burn you.
Do not get it on you. If you accidentally get it
in your eyes or on your skin, ush the place
with water and get medical help immediately.
{CAUTION:
Fans or other moving engine parts can injure
you badly. Keep your hands away from moving
parts once the engine is running.
5. Check that the jumper cables do not have loose or
missing insulation. If they do, you could get a
shock. The vehicles could be damaged too.
Before you connect the cables, here are some
basic things you should know. Positive (+) will go to
positive (+) or to a remote positive (+) terminal if
the vehicle has one. Negative (−) will go to a heavy,
unpainted metal engine part or to a remote
negative (−) terminal if the vehicle has one.
Do not connect positive (+) to negative (−)oryou
will get a short that would damage the battery
and maybe other parts too. And do not connect the
negative (−) cable to the negative (−) terminal on
the dead battery because this can cause sparks.
5-45
ProCarManuals.com

6. Remove the terminal cover and connect the red
positive (+) cable to the positive (+) terminal of
the dead battery. Use a remote positive (+) terminal
if the vehicle has one.
7. Do not let the other end touch metal. Connect it to
the positive (+) terminal of the good battery. Use a
remote positive (+) terminal if the vehicle has one.8. Now connect the black negative (−) cable to the
negative (−) terminal of the good battery. Use a
remote negative (−) terminal if the vehicle has one.
Do not let the other end touch anything until the
next step. The other end of the negative (−) cable
does not go to the dead battery. It goes to a
heavy, unpainted metal engine part or to a remote
negative (−) terminal on the vehicle with the
dead battery.
9. Connect the other end of the negative (−) cable at
least 18 inches (45 cm) away from the dead battery,
but not near engine parts that move. The electrical
connection is just as good there, and the chance
of sparks getting back to the battery is much less.
Your vehicle has a remote negative (−) terminal
for this purpose.
10. Now start the vehicle with the good battery and run
the engine for a while.
11. Press the unlock button on the remote keyless
entry transmitter to disarm your security system,
if equipped.
12. Try to start the vehicle that had the dead battery.
If it will not start after a few tries, it probably needs
service.
5-46
ProCarManuals.com

Notice:If the jumper cables are connected or
removed in the wrong order, electrical shorting may
occur and damage the vehicle. The repairs would
not be covered by your warranty. Always connect
and remove the jumper cables in the correct
order, making sure that the cables do not touch
each other or other metal.
A. Heavy, Unpainted Metal Engine Part
B. Good Battery
C. Dead BatteryTo disconnect the jumper cables from both vehicles,
do the following:
1. Disconnect the black negative (−) cable from the
vehicle that had the dead battery.
2. Disconnect the black negative (−) cable from the
vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the
other vehicle.
5. Return the red protector cap to its original position.
Jumper Cable Removal
5-47
ProCarManuals.com

Headlamp Aiming
Headlamp aim has been preset at the factory and
should need no further adjustment.
If your vehicle is damaged in an accident, the headlamp
aim may be affected. Aim adjustment to the low-beam
headlamps may be necessary if it is difficult to see
the lane markers (for horizontal aim), or if oncoming
drivers ash their high-beam headlamps at you
(for vertical aim). If you believe your headlamps need
to be re-aimed, we recommend that you take your
vehicle to your retailer for service.
Bulb Replacement
For the type of bulb to use, seeReplacement Bulbs
on page 5-55.
For any bulb changing procedure not listed in this
section, contact your retailer.
Halogen Bulbs
{CAUTION:
Halogen bulbs have pressurized gas inside
and can burst if you drop or scratch the bulb.
You or others could be injured. Be sure to
read and follow the instructions on the bulb
package.
5-48
ProCarManuals.com

Headlamps (Coupe)
To change a headlamp bulb on a coupe model, do the
following:
1. Open the hood. SeeHood Release on page 5-10
for more information.
2. Pull up on the headlamp retaining pins to remove
them from the headlamp assembly.
3. Pull the headlamp assembly away from the vehicle
and remove the electrical connector.4. Raise the lock tab and pull the connector from the
base of the bulb to remove the electrical connector
from the headlamp bulb.
5. Remove the retaining nut by turning it
counterclockwise.
6. Remove the bulb and replace it with the
appropriate bulb.
7. Reverse the steps to reinstall the headlamp
assembly.
5-49
ProCarManuals.com

Headlamps (Sedan)
To change a headlamp bulb on a sedan model, do the
following:
1. Open the hood. SeeHood Release on page 5-10
for more information.
2. Pull up on the headlamp retaining pins to remove
them from the headlamp assembly.
3. Pull the headlamp assembly away from the vehicle
and remove the electrical connector.4. Access the bulb by turning the dust cap
counterclockwise to remove it.
5-50
ProCarManuals.com

5. Raise the lock tab and pull the connector (A) from
the base of the bulb to remove the electrical
connector.
6. Remove the bulb retaining nut by turning it
counterclockwise.
7. Remove the bulb and replace it with the
appropriate bulb.
8. Reverse the steps to reinstall the lamp assembly.
5-51
ProCarManuals.com

Front Turn Signal, Parking and
Daytime Running Lamps (DRL)
(Coupe)
To change this bulb on a coupe model, do the following:
1. Open the hood. SeeHood Release on page 5-10
for more information.
2. Reach behind the headlamp from inside the hood.
3. Rotate the bulb socket counterclockwise to
remove it from the housing.
4. Pull the bulb from the socket and replace it with the
appropriate bulb.
5. Reinstall the bulb socket by turning it clockwise.
5-52
ProCarManuals.com

Front Turn Signal, Parking and
Daytime Running Lamps (DRL)
(Sedan)
To change this bulb on a sedan model, do the following:
1. Follow Steps 1 through 4 to remove the headlamp
assembly. See the headlamp removal for sedan
underHeadlamps (Coupe) on page 5-49or
Headlamps (Sedan) on page 5-50. This bulb is
located next to the high/low-beam headlamp.
2. Remove the bulb socket by rotating it
counterclockwise.
3. Remove the bulb and replace it with the
appropriate bulb.
4. Reverse the steps to reinstall the lamp assembly.
5-53
ProCarManuals.com

Center High-Mounted Stoplamp
(CHMSL)
To change a CHMSL bulb, do the following:
1. Remove the CHMSL cover by pulling down on the
cover edges from inside the vehicle.
2. Turn the bulb socket counterclockwise to remove it.
3. Replace with the appropriate bulb.
4. Reinstall the bulb socket by turning it clockwise.
5. Replace the cover.
Taillamps, Turn Signal, Stoplamps
and Back-up Lamps
To change one of these bulbs, do the following:
1. Open the trunk. SeeTrunk on page 2-11for more
information.
2. Remove the three retaining screws from the
taillamp assembly.
3. Slide the taillamp assembly back and remove it
from the quarter panel.
5-54
ProCarManuals.com