windshield wipers SATURN L-SERIES 2005 Owners Manual

Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high or
high beam to low, pull the turn signal lever all the way
towards you. Then release it.
When the high beams are
on, this light on the
instrument panel cluster
will also be on.
Flash-to-Pass
This feature lets you use your high-beam headlamps to
signal a driver in front of you that you want to pass.
To use it, pull the turn signal/multifunction lever toward
you until the high-beam headlamps come on, then
release the lever to turn them off.
Windshield Washer
{CAUTION:
In freezing weather, do not use your washer
until the windshield is warmed. Otherwise the
washer uid can form ice on the windshield,
blocking your vision.
Pull the windshield wiper lever toward you to operate
the windshield wipers. Washer fluid will squirt onto
the windshield and the wipers will run for a few cycles
to clear the windshield. For more wash cycles, pull
the lever toward you and hold it there.
3-8
ProCarManuals.com

Windshield Wiper Lever
The lever on the right side of the steering column
operates the windshield wipers.
8:Pull the lever down and release it for a single
wiping cycle. The lever will return to its original position.
For more cycles, hold the lever down before releasing it.
9:Put the lever in this position to turn off the wipers.
&:Put the lever in this position to set a delay
between wipes. Turn the band on the lever to set the
length of the delay (1, 2, or 3).
OO:Put the lever in this position for slow, steady
wiping cycles.
OOOO:Put the lever in this position for rapid
wiping cycles.
Be sure to clear ice and snow from the wiper blades
before using them. If they’re frozen to the windshield,
gently loosen or thaw them. If the blades do become
damaged, install new blades or blade inserts.
Heavy snow or ice can overload the wiper motor. A
circuit breaker will stop the motor until it cools down.
Clear away snow or ice to prevent an overload.
3-9
ProCarManuals.com

Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected at least
twice a year for wear or cracking. See “Windshield
Wipers, Blade Check” underScheduled Maintenance
on page 6-4for more information.
Replacement blades come in different types and are
removed in different ways. For proper type and length,
seeNormal Maintenance Replacement Parts on
page 6-14. Here’s how to remove the wiper blades:
1. Turn on the wipers to the low wipe setting.
2. Turn off the ignition while the wipers are at the
outer positions of the wiper pattern. The blades
are more accessible for removal/replacement
while in this position.
3. Pull the windshield wiper arm away from the
windshield.4. While holding the wiper arm away from the glass,
push the release clip from under the blade
connecting point and pull the old blade assembly
down toward the glass to remove it from the
wiper arm.
5. Push the new wiper blade securely on the wiper
arm until you hear the release clip “click” into place.
5-47
ProCarManuals.com

Floor Console Fuse Block
The driver’s side instrument panel is located under the
instrument panel on the driver’s left side.
Use a key or a coin to remove the fuse panel door and
access the fuses and relays.
Fuses Usage
DIMMER Dimmer Switch
IGN 3Left Heated Seat Switch
(If Equipped), Right Heated
Seat Switch (If Equipped), Air
Conditioning, Rear Defogger Relay
DEFOG LED Rear Defog LED
RR COMP Trunk Compartment Lamp
WIPERWindshield Washers and
Wipers (Front)
BTSI/BCM/
MIRRORBrake Transaxle Shift Interlock,
Body Control Module, Power Mirror
RADIOAudio, OnStar
®, Rear Seat DVD
(Option)
Relays Usage
IGN 3 Ignition Switch
REAR DEFOG Rear Defogger
HEADLAMP Headlamps
PARKLAMP Park Lamps
Misc. Usage
FUSE PULLER Fuse Puller
5-84
ProCarManuals.com