ECU SATURN OUTLOOK 2008 Workshop Manual
[x] Cancel search | Manufacturer: SATURN, Model Year: 2008, Model line: OUTLOOK, Model: SATURN OUTLOOK 2008Pages: 488, PDF Size: 3 MB
Page 404 of 488

Removing the Flat Tire and
Installing the Spare Tire
1. Do a safety check before proceeding. SeeChanging
a Flat Tire on page 5-84for more information.
2. If the vehicle has a wheel cover, loosen the plastic
nut caps with the lug wrench. They will not come
off. Then, using the at end of the lug wrench,
pry along the edge of the cover until it comes off.
Be careful; the edges may be sharp. Do not
try to remove the cover with your bare hands.
Store the wheel cover securely in the rear of the
vehicle until you have the at tire repaired or
replaced.
If your vehicle has aluminum wheels, remove the
wheel nut caps using the lug wrench.3. Loosen the wheel nuts — but do not remove
them — using the lug wrench. For wheels with
a wheel lock key, use the wheel lock key between
the lock nut and lug wrench.
Notice:If your vehicle has wheel locks and an
impact wrench is used to remove the wheel nuts,
the lock nut or wheel lock key could be damaged.
Do not use an impact wrench to remove the
wheel nuts if your vehicle has wheel locks.
5-88
ProCarManuals.com
Page 413 of 488

5. Raise the tire fully against the underside of the
vehicle. Continue turning the lug wrench until you
feel more than two clicks. This indicates that the
compact spare tire is secure and the cable is tight.
The spare tire hoist cannot be overtightened.
6. Make sure the tire is stored securely. Push, pull (A),
and then try to turn (B) the tire. If the tire moves,
use the lug wrench to tighten the cable.Storing the Flat Tire
Notice:Storing the full-size at tire in the
underbody hoist system can expose it to heat
from the exhaust system. This can damage the
tire and underbody hoist system. Do not store the
full-size at tire in the underbody hoist system.
1. Remove the cable package from the jack
storage area.
2. Remove the small center cap by tapping the back
of the cap with the extension of the shaft, if the
vehicle has aluminum wheels.
3. Put the at tire in the rear storage area with the
valve stem pointing toward the rear of the vehicle.
5-97
ProCarManuals.com
Page 414 of 488

4. Hook one end of the cable onto the outside portion
of the liftgate hinge opposite (B).
5. Pull the cable (A) through the center of the
wheel (D), then the door striker (E), and the spare
tire heat shield (C).6. Hook the other end of
the cable onto the
outer portion of
the liftgate hinge (B).
7. Pull on the cable to make sure it is secure.
8. The metal tube should be centered at the striker.
9. Push the tube toward
the front of the vehicle.
10. Close the liftgate and latch it properly.
5-98
ProCarManuals.com
Page 415 of 488

Storing the Tools
A. Tool Bag
B. Wing Bolt
C. JackPut back all tools as they were stored in the jack
storage compartment and put the compartment cover
back on.
1. Attach the tool bag to the jack.
2. Make sure that the bottom of the jack is facing
toward you.
3. Turn the jack (C) on its side and place it down on
the holding bracket.
4. Reinstall the wing bolt (B) by turning it clockwise.
5. To replace the cover, line up the tabs on the bottom
of the cover with the slots in the cover opening.
Push the cover in place, insuring that the upper front
and rear tabs are in the opening and push the
cover closed. The center latch should be fully
engaged. This secures the cover in place.
Store the center cap or the plastic bolt-on wheel covers
until a full size tire is put back on the vehicle. When you
replace the compact spare with a full-size tire, reinstall
the bolt-on wheel covers or the center cap. Hand-tighten
them over the wheel nuts, using the lug wrench.
5-99
ProCarManuals.com