engine SATURN VUE 2007 Manual PDF

What Kind of Engine Oil to Use
For Vehicles with the 2.2L L4 Engine Only
Look for three things:
GM6094M
Your vehicle’s engine requires oil meeting GM
Standard GM6094M. Look for and use only
an oil that meets GM Standard GM6094M.
SAE 5W-30
As shown in the viscosity chart, SAE 5W-30 is
best for your vehicle.
These numbers on an oil container show its
viscosity, or thickness. Do not use other
viscosity oils such as SAE 20W-50.
320
ProCarManuals.com

Oils meeting these
requirements should
have the starburst
symbol on the
container. This
symbol indicates that
the oil has been
certied by the
American Petroleum
Institute (API).
Look for this information on the oil container, and
use only those oils that are identied as meeting
GM Standard GM6094M and have the starburst
symbol on the front of the oil container.Notice:Use only engine oil identied as
meeting GM Standard GM6094M and showing
the American Petroleum Institute Certied
For Gasoline Engines starburst symbol. Failure
to use the recommended oil can result in
engine damage not covered by your warranty.
If you are in an area of extreme cold, where
the temperature falls below−20°F (−29°C), it is
recommended that you use either an SAE 5W-30
synthetic oil or an SAE 0W-30 oil. Both provide
easier cold starting and better protection for
the engine at extremely low temperatures.
321
ProCarManuals.com

For Vehicles with the 3.5L V6 Engine Only
As shown in the viscosity chart, SAE 5W-20 is
best for your vehicle.
These numbers on an oil container show its
viscosity, or thickness. Do not use other viscosity
oils such as SAE 20W-50.Oils meeting these
requirements should
also have the starburst
symbol on the
container. This symbol
indicates that the oil
has been certied by the
American Petroleum
Institute (API).
Look for this information on the oil container,
and use only those oils that have the starburst
symbol on the front of the oil container.
Notice:Use only engine oil with the American
Petroleum Institute Certied For Gasoline
Engines starburst symbol. Failure to use the
recommended oil can result in engine damage
not covered by your warranty.
Engine Oil Additives
Do not add anything to the oil. The recommended
oil with the starburst symbol are all you need
for good performance and engine protection.
322
ProCarManuals.com

Engine Oil Life System
When to Change Engine Oil
Your vehicle has a computer system that lets you
know when to change the engine oil and lter.
This is based on engine revolutions and engine
temperature, and not on mileage. Based on driving
conditions, the mileage at which an oil change
will be indicated can vary considerably. For the oil
life system to work properly, you must reset the
system every time the oil is changed.
When the system has calculated that oil life has
been diminished, it will indicate that an oil change is
necessary. A change engine oil light will come on.
SeeChange Engine Oil Light on page 179. Change
the oil as soon as possible within the next 600 miles
(1 000 km). It is possible that, if you are driving
under the best conditions, the oil life system might
not indicate that an oil change is necessary for over
a year. However, the engine oil and lter must be
changed at least once a year and at this time the
system must be reset. Your dealer/retailer has
trained service people who will perform this work
using genuine parts and reset the system. It is also
important to check the oil regularly and keep it at
the proper level.If the system is ever reset accidentally, you must
change the oil at 3,000 miles (5 000 km) since
your last oil change. Remember to reset the oil life
system whenever the oil is changed.
How to Reset the Engine Oil Life
System
The Engine Oil Life System calculates when to
change the engine oil and lter based on vehicle
use. Whenever the oil is changed, reset the
system so it can calculate when the next oil
change is required. If a situation occurs where you
change the oil prior to a change engine oil light
being turned on, reset the system.
After changing the engine oil, reset the system:
1. Turn the ignition key to RUN with the
engine off.
2. Fully press and release the accelerator pedal
three times within ve seconds.
If the change engine oil light is ashing, the
system is reset. The light will ash for up
to 30 seconds or until the ignition is turned off.
If the light comes on again and stays on for
30 seconds at the next ignition cycle, it did not
reset. You will need to reset the system again.
323
ProCarManuals.com

What to Do with Used Oil
Used engine oil contains certain elements that can
be unhealthy for your skin and could even cause
cancer. Do not let used oil stay on your skin for very
long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly
dispose of clothing or rags containing used engine
oil. See the manufacturer’s warnings about the use
and disposal of oil products.
Used oil can be a threat to the environment. If you
change your own oil, be sure to drain all the oil
from the lter before disposal. Never dispose
of oil by putting it in the trash, pouring it on the
ground, into sewers, or into streams or bodies of
water. Instead, recycle it by taking it to a place
that collects used oil. If you have a problem
properly disposing of used oil, ask your
dealer/retailer, a service station, or a local
recycling center for help.
Engine Air Cleaner/Filter
SeeEngine Compartment Overview on page 314
for the location of the engine air cleaner/lter.
When to Inspect the Engine Air
Cleaner/Filter
Inspect the air cleaner/lter at the MaintenanceII
intervals and replace it at the rst oil change
after each 50,000 mile (83 000 km) interval. See
Scheduled Maintenance on page 420for more
information. If you are driving in dusty/dirty
conditions, inspect the lter at each engine
oil change.
How to Inspect the Engine Air
Cleaner/Filter
To inspect the air cleaner/lter remove the lter
from the vehicle and lightly shake the lter to
release loose dust and dirt. If the lter remains
caked with dirt, a new lter is required.
324
ProCarManuals.com

To inspect or replace the engine air cleaner/lter,
do the following:
1. Unscrew the clamp on the air duct hose.2. Disconnect the hose.
325
ProCarManuals.com

3. Release the clamps on the side of the air
cleaner assembly.
4. Turn the cover upward to disengage the
cover hinges.5. Remove the air cleaner cover assembly and
air lter element.
6. Inspect or replace the air lter element.
If the air lter element is dirty, you should
replace it. If it is only dusty, it may be cleaned
by blowing compressed air through it from
the clean side.
Make sure you are away from the engine
compartment when cleaning the air lter with
compressed air.
326
ProCarManuals.com

Wipe all dust from inside of the housing and
inspect the air cleaner and air outlet duct
for cracks, cuts and deterioration. The
air outlet duct must be replaced if damaged.
7. Reverse Steps 1 through 5 to reinstall
the engine air cleaner/lter cover and air
duct hose.
{CAUTION:
Operating the engine with the air cleaner/
lter off can cause you or others to be
burned. The air cleaner not only cleans the
air; it helps to stop ames if the engine
backres. If it is not there and the engine
backres, you could be burned. Do not
drive with it off, and be careful working on
the engine with the air cleaner/lter off.
Notice:If the air cleaner/lter is off, a backre
can cause a damaging engine re. And, dirt
can easily get into your engine, which will
damage it. Always have the air cleaner/lter
in place when you are driving.
Automatic Transaxle Fluid
(2.2L L4 Engine)
When to Check and Change Automatic
Transaxle Fluid
A good time to check your automatic transaxle
uid level is when the engine oil is changed.
Change the uid at the intervals listed inAdditional
Required Services on page 423, and be sure to
use the transaxle uid listed inRecommended
Fluids and Lubricants on page 432.
How to Check Automatic
Transaxle Fluid
If your vehicle is equipped with the 2.2L L4
engine, you will have to have this procedure done
at your retailer’s service department.
Notice:Use of the incorrect automatic
transaxle uid may damage your vehicle, and
the damages may not be covered by your
warranty. Always use the automatic transaxle
uid listed inRecommended Fluids and
Lubricants on page 432.
327
ProCarManuals.com

Automatic Transaxle Fluid
(3.5L V6 Engine)
When to Check and Change Automatic
Transaxle Fluid
A good time to check your automatic transaxle
uid level is when the engine oil is changed.
Change the uid at the intervals listed inAdditional
Required Services on page 423, and be sure to
use the transaxle uid listed inRecommended
Fluids and Lubricants on page 432.
How to Check Automatic
Transaxle Fluid
Because this operation can be a little difficult, you
may choose to have this done at your retailer’s
service department.
If you do it yourself, be sure to follow all the
instructions here, or you could get a false reading
on the dipstick.Notice:Too much or too little uid can damage
the transaxle. Too much can mean that some of
the uid could come out and fall on hot engine
or exhaust system parts, starting a re. Too
little uid could cause the transaxle to overheat.
Be sure to get an accurate reading if you check
the transaxle uid.
Wait at least 30 minutes before checking the
transaxle uid level if you have been driving:
When outside temperatures are
above 90°F (32°C).
At high speed for quite a while.
In heavy traffic — especially in hot weather.
While pulling a trailer.
To get the right reading, the uid should be at
normal operating temperature, which is 180°F to
200°F (82°C to 93°C).
Get the vehicle warmed up by driving about
15 miles (24 km) when outside temperatures are
above 50°F (10°C). If it is colder than 50°F (10°C),
you may have to drive longer.
328
ProCarManuals.com

Checking the Fluid Level
Prepare your vehicle as follows:
1. Park your vehicle on a level place.
2. Warm the engine to normal operating
temperature until the electric radiator fan turns
on at least once.
3. With the parking brake applied, place the shift
lever in PARK (P).
4. With your foot on the brake pedal, move the
shift lever through each gear range, pausing
for about three seconds in each range.
Then, position the shift lever in PARK (P).Then, turn off the engine and follow these steps:
The transaxle uid dipstick handle is the black loop
near the rear of the engine compartment, toward
the center.
1. Pull out the dipstick and wipe it with a clean
rag or paper towel.
2. Push it back in all the way, wait three seconds
and then pull it back out again.
3. Check both sides of the dipstick, and read the
lower level. The uid level must be between
the upper mark and the lower mark.
4. If the uid level is in the acceptable range,
push the dipstick back in all the way.
329
ProCarManuals.com