lock SATURN VUE 2010 Owners Manual

10-40 Vehicle Care
RelaysUsage
FAN
MAIN RLY Cooling Fan Main
Relay
FAN
CTRL RLY Cooling Fan
Control Relay
FAN
AUX RLY Cooling Fan
Auxiliary Relay
PWR/
TRN RLY Engine Control
Module/CAM,
Canister, Injectors,
Electronic Throttle
Control Relay
STRTR RLY Starter Relay RUN RLY Run Relay
A/C
CLTCH RLY Air Conditioning
Compressor Relay
WPR
SPD RLY Windshield Wiper
Speed Relay Relays
Usage
HORN RLY Horn Relay WPR
CNTRL RLY Windshield Wiper
Control Relay
T/LAMP RLY Parking Lamp Relay
HDLP
HI RLY High-Beam
Headlamp Relay
HDLP
LO RLY Low‐Beam
Headlamp Relay
FRT
FOG RLY Front Foglamp
Relay
STOP
LP RLY Stoplamp Relay
DEFOG RLY Defogger RelayInstrument Panel Fuse
Block
The instrument panel fuse block is
located on the passenger side of the
lower console.
Pull the latch of the fuse box cover
straight back to access the fuses.
ProCarManuals.com

10-42 Vehicle Care
Fuses Usage
F/DR LCK Front Driver
Door Lock
APO2 Accessory Power
Outlet 2
BCM (VB3) Body Control
Module (BCM) (VB3)
DR LCK Door Lock
BCM (VB6) Body Control
Module (VB6)
BCM (VB4) Body Control
Module (VB4)
BCM (VB5) Body Control
Module (VB5)
TRL Trailer
AIRCON Air Conditioner AUDIO Audio Fuses Usage
BCM (VB7) Body Control
Module (VB7)
IGN SW Ignition Switch
AIR BAG Air Bag System
WASHER Washer Pump
APO1 Accessory Power
Outlet 1
FSCM Fuel Storage Control
Module
RR CLR Rear Closure
BCM (VB2) Body Control
Module (VB2)
DRL Daytime Running
Light
BCM (VB1) Body Control
Module (VB1)
ONSTAR OnStar
®
Relays Usage
RELAY
ACC/RAP Accessory, Retained
Accessory Power
(RAP) Relay
RELAY RUN/
CRANK Run/Crank Relay
ProCarManuals.com

10-56 Vehicle Care
TPMS Sensor Matching
Process
Each TPMS sensor has a unique
identification code. Any time you
replace one or more of the TPMS
sensors or rotate the vehicle's tires,
the identification codes will need to
be matched to the new tire/wheel
position. The sensors are matched,
to the tire/wheel positions, in the
following order: driver side front tire,
passenger side front tire, passenger
side rear tire, and driver side rear
tire using a TPMS diagnostic tool.
See your dealer/retailer for service.
The TPMS sensors can also be
matched to each tire/wheel position
by increasing or decreasing the
tire's air pressure. When increasing
the tire's pressure, do not exceed
the maximum inflation pressure
indicated on the tire's sidewall.To decrease the tire's air-pressure
use the pointed end of the valve
cap, a pencil-style air pressure
gage, or a key.
You have two minutes to match
each tire and wheel position. If it
takes longer than two minutes to
match any tire and wheel position,
the matching process stops and
you will need to start over.
The TPMS matching process is
outlined below:
1. Set the parking brake.
2. Turn the ignition switch to
ON/RUN with the engine off.
3. Press and hold the RKE transmitter's Lock and Unlock
buttons at the same time, for
about three seconds. The horn
will sound twice to indicate the
receiver is ready for the sensor
matching process to begin. 4. Start with the driver side front
tire. The driver side turn signal
lamp comes on.
5. Remove the valve cap from the tire's valve stem. Activate the
TPMS sensor by increasing or
decreasing the tire's air pressure
for five seconds, or until a horn
chirp sounds. The horn chirp,
which may take up to
30 seconds to sound, confirms
that the sensor identification
code has been matched to the
tire/wheel position.
6. Proceed to the passenger side front tire. The passenger side
front turn signal lamp comes on.
Repeat the procedure in Step 5.
7. Proceed to the passenger side rear tire. The passenger side
rear turn signal lamp comes on.
Repeat the procedure in Step 5.
ProCarManuals.com

Vehicle Care 10-57
8. Proceed to the driver side reartire. The driver side rear turn
signal lamp comes on. Repeat
the procedure in Step 5.
The horn sounds two times to
indicate the sensor identification
code has been matched to the
driver side rear tire, and the
TPMS sensor matching process
is no longer active.
9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure
level as indicated on the Tire
and Loading Information label.
11. Put the valve caps back on the valve stems.Tire Inspection
We recommend that you
regularly inspect your vehicle's
tires, including the spare tire,
if the vehicle has one, for signs
of wear or damage. See When It
Is Time for New Tires
on
page 10‑58
for more information.
Tire Rotation
Tires should be rotated every
8 000 to 13 000 km (5,000 to
8,000 miles). See Scheduled
Maintenance
on page 11‑2.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that the vehicle
continues to perform most like it
did when the tires were new. Any time you notice unusual
wear, rotate the tires as soon
as possible and check wheel
alignment. Also check for
damaged tires or wheels.
See
When It Is Time for New
Tires
on page 10‑58and Wheel
Replacement
on page 10‑64.
When rotating the vehicle's tires,
always use the correct rotation
pattern shown here.
ProCarManuals.com

Vehicle Care 10-61
Vehicles that have a tire
pressure monitoring system
could give an inaccurate
low‐pressure warning if non‐TPC
Spec rated tires are installed
on your vehicle. Non‐TPC
Spec rated tires may give a
low‐pressure warning that is
higher or lower than the proper
warning level you would get with
TPC Spec rated tires. SeeTire
Pressure Monitor System
on
page 10‑52
.
Your vehicle's original
equipment tires are listed on the
Tire and Loading Information
Label. See Vehicle Load Limits
on page 9‑22, for more
information about the Tire and
Loading Information Label and
its location on your vehicle.
Different Size Tires and
Wheels
If you add wheels or tires that are a
different size than your original
equipment wheels and tires, this
may affect the way your vehicle
performs, including its braking, ride
and handling characteristics,
stability, and resistance to rollover.
Additionally, if your vehicle has
electronic systems such as,
anti‐lock brakes, rollover airbags,
traction control, and stability control,
the performance of these systems
can be affected.
{WARNING
If you add different sized
wheels, your vehicle may not
provide an acceptable level of
performance and safety if tires not
recommended for those wheels
are selected. You may increase
the chance that you will crash and
suffer serious injury. Only use
Saturn specific wheel and tire
systems developed for your
vehicle, and have them properly
installed by a Saturn certified
technician.
See Buying New Tires
on
page 10‑59and Accessories and
Modificationson page 10‑3for
additional information.
ProCarManuals.com

10-66 Vehicle Care
If a tire goes flat, avoid further tire
and wheel damage by driving slowly
to a level place. Turn on the hazard
warning flashers. SeeHazard
Warning Flashers on page 6‑3.
{WARNING
Changing a tire can be
dangerous. The vehicle can slip
off the jack and roll over or fall on
you or other people. You and they
could be badly injured or even
killed. Find a level place to
change your tire. To help prevent
the vehicle from moving:
1. Set the parking brake firmly.
2. Put an automatic transmission shift lever in
P (Park), or shift a manual
transmission to 1 (First) or
R (Reverse).
(Continued)
WARNING (Continued)
3. Turn off the engine and donot restart while the vehicle
is raised.
4. Do not allow passengers to remain in the vehicle.
To be certain the vehicle will not
move, put blocks at the front and
rear of the tire farthest away
from the one being changed.
That would be the tire on the
other side, at the opposite end of
the vehicle. When the vehicle has a flat tire (B),
use the following example as a
guide to assist you in the placement
of wheel blocks (A).
A. Wheel Block
B. Flat Tire
The following information explains
how to repair or change a tire.
ProCarManuals.com

Vehicle Care 10-67
Tire Changing
Removing the Spare Tire
and Tools
To access the spare tire:
1. Open the liftgate.
2. Push the levers on the load floor.
3. Lift the load floor and hang thehook to the tailgate opening.
4. Remove the tire protector foam.5. Remove the wheel retainer boltholding down the spare tire by
turning it counterclockwise.
6. Remove the compact spare tire. See Compact Spare Tire
on
page 10‑73for more information.
ProCarManuals.com

10-68 Vehicle Care
The tools are located between the
compact spare tire and the liftgate.
To access the tools:
A. Tool Bag
B. Wing-bolt
C. Jack
1. Remove the wing-bolt (B) fromthe jack.
2. Remove the jack (C) and tool bag (A). 3. Remove the straps holding the
bag containing the wheel wrench
and extension jack handle.
Remove the wheel wrench and
extension jack handle from
the bag.
The tools you will be using include:
A. Tool Bag
B. Jack
C. Wheel Wrench
D. Extension Jack Handle
Removing the Flat Tire and
Installing the Spare Tire
1. Do a safety check before proceeding. See If a Tire Goes
Flat
on page 10‑65for more
information.
2. Use the wheel wrench to loosen all the wheel nuts. Do not
remove them yet.
3. Attach the wheel wrench to the jack bolt head and rotate the
wheel wrench clockwise to raise
the lift head a little.
ProCarManuals.com

Vehicle Care 10-69
4. Position the lift head at the jacklocation nearest the flat tire.
Make sure all of the jack lift
head is touching the jacking
flange under the body. Do not
place the jack under a body
panel. The lower body panel has
an arrow to aid in locating the
jacking location.
5. Put the compact spare tire near you.6. Raise the vehicle by turning thejack handle clockwise. Raise the
vehicle far enough off the
ground so there is enough room
for the road tire to be removed.
{WARNING
Getting under a vehicle when it is
jacked up is dangerous. If the
vehicle slips off the jack, you
could be badly injured or killed.
Never get under a vehicle when it
is supported only by a jack.
{WARNING
Raising your vehicle with the
jack improperly positioned can
damage the vehicle and even
make the vehicle fall. To help
avoid personal injury and vehicle
damage, be sure to fit the jack lift
head into the proper location
before raising the vehicle.
ProCarManuals.com

10-70 Vehicle Care
{WARNING
Lifting a vehicle and getting
under it to do maintenance or
repairs is dangerous without the
appropriate safety equipment and
training. If a jack is provided with
the vehicle, it is designed only for
changing a flat tire. If it is used for
anything else, you or others could
be badly injured or killed if the
vehicle slips off the jack. If a jack
is provided with the vehicle, only
use it for changing a flat tire.
Notice: Make sure that the jack
lift head is in the correct position
or you may damage your vehicle.
The repairs would not be covered
by your warranty.
7. Remove all of the wheel nuts.
8. Remove the flat tire.
9. Remove any rust or dirt from the wheel bolts, mounting surfaces
and spare wheel.
{WARNING
Rust or dirt on a wheel, or on the
parts to which it is fastened, can
make wheel nuts become loose
after time. The wheel could come
off and cause an accident. When
changing a wheel, remove any
rust or dirt from places where the
wheel attaches to the vehicle.
In an emergency, use a cloth or a
paper towel to do this; but be sure
to use a scraper or wire brush
later, if needed, to get all the rust
or dirt off. See If a Tire Goes Flat
on page 10‑65.
10. Place the compact spare tire on the wheel‐mounting surface.
11. Reinstall the wheel nuts. Tighten each nut by hand until
the wheel is held against
the hub.
{WARNING
Never use oil or grease on bolts
or nuts because the nuts might
come loose. The vehicle's wheel
could fall off, causing a crash.
12. Lower the vehicle by turningthe jack handle
counterclockwise.
ProCarManuals.com