clock SATURN VUE HYBRID 2008 User Guide

{CAUTION:
Fuel can spray out on you if you open the
fuel cap too quickly. If you spill fuel and then
something ignites it, you could be badly burned.
This spray can happen if your tank is nearly full,
and is more likely in hot weather. Open the fuel
cap slowly and wait for any hiss noise to stop.
Then unscrew the cap all the way.
Be careful not to spill fuel. Do not top off or overll the
tank and wait a few seconds after you have nished
pumping before removing the nozzle. Clean fuel from
painted surfaces as soon as possible. SeeWashing
Your Vehicle on page 5-82.
When replacing the fuel cap, turn it clockwise until it
clicks. Make sure the cap is fully installed. The diagnostic
system can determine if the fuel cap has been left off or
improperly installed. This would allow fuel to evaporate
into the atmosphere. SeeMalfunction Indicator Lamp on
page 3-36.
{CAUTION:
If a re starts while you are refueling, do not
remove the nozzle. Shut off the ow of fuel by
shutting off the pump or by notifying the
station attendant. Leave the area immediately.
Notice:If you need a new fuel cap, be sure to get
the right type. Your dealer/ retailer can get one
for you. If you get the wrong type, it may not
t properly. This may cause your malfunction
indicator lamp to light and may damage your fuel
tank and emissions system. SeeMalfunction
Indicator Lamp on page 3-36.
5-9
ProCarManuals.com

{CAUTION:
You can be burned if you spill coolant on hot
engine parts. Coolant contains ethylene glycol
and it will burn if the engine parts are hot
enough. Do not spill coolant on a hot engine.
1. You can remove the
coolant surge tank
pressure cap when
the cooling system,
including the coolant
surge tank pressure
cap and upper radiator
hose, is no longer hot.
Turn the pressure cap slowly counterclockwise
about one-quarter of a turn. If you hear a hiss,
wait for that to stop. This will allow any pressure
still left to be vented out the discharge hose.
2. Then keep turning the pressure cap slowly, and
remove it.3. Fill the coolant surge tank with the proper
DEX-COOL
®coolant mixture, to between the
MIN and MAX lines.
4. With the coolant surge tank pressure cap off, start
the engine and let it run until you can feel the upper
radiator hose getting hot. Watch out for the engine
cooling fan.
By this time, the coolant level inside the coolant
surge tank may be lower. If the level is lower, add
more of the proper DEX-COOL
®coolant mixture
to the coolant surge tank until the level reaches
between the MIN and MAX lines.
5. Then replace the pressure cap. Be sure the
pressure cap is hand-tight.
5-28
ProCarManuals.com

4. At the wall measure from the ground upward (A) to
the recorded distance from Step 3 and mark it.
5. Draw or tape a horizontal line (B) on the wall the
width of the vehicle at the height of the mark in
Step 4.
Notice:Do not cover a headlamp to improve beam
cut-off when aiming. Covering a headlamp may
cause excessive heat build-up which may cause
damage to the headlamp.
6. Turn on the low-beam headlamps and place a
piece of cardboard or equivalent in front of the
headlamp not being adjusted. This allows only the
beam of light from the headlamp being adjusted
to be seen on the at surface.7. Locate the vertical headlamp aiming screws, which
are under the hood near each headlamp assembly.
The adjustment screw can be turned with a
E8 Torx
®socket.
8. Turn the vertical aiming screw until the headlamp
beam is aimed to the horizontal tape line. Turn it
clockwise or counterclockwise to raise or lower the
angle of the beam.
5-40
ProCarManuals.com

Headlamps
To replace one of the headlamp bulbs, use the following
procedure. To replace the parking/turn signal lamp
bulb, seeFront Turn Signal and Parking Lamps
on page 5-43.
1. Open the hood. SeeHood Release on page 5-11
for more information.
2. Remove the two screws from the top of the front
fascia and grille. They are inboard of the headlamp
assembly.
3. Remove the three screws retaining the headlamp
assembly.
4. Insert a at blade tool through the opening in the
top. Make sure the tool ts through the opening in
the headlamp bracket lower arm.
5. Push the locking tab toward the rear of the vehicle
with the tool to lift the headlamp bracket lower arm.
6. Pull back on the front fascia and then pull the
headlamp assembly out from the vehicle. Another
person might be needed to assist with this step.7. Disconnect the electrical connector from the bulb
assembly.
8. Turn the bulb assembly counterclockwise to remove
it from the housing.
9. Replace the old bulb with a new one.
10. Reverse Steps 1 through 8 to reinstall.
5-42
ProCarManuals.com

Front Turn Signal and Parking
Lamps
To replace a front turn signal or parking lamp bulb:
1. Follow Steps 1 through 6 underHeadlamps
on page 5-42to access the front turn signal
or parking lamp.
2. Turn the bulb to be replaced counterclockwise to
remove it from the headlamp assembly.3. Pull the bulb out of the bulb socket assembly.
4. Push the new bulb into the bulb socket assembly.
5. Insert the bulb assembly into the headlamp
assembly.
6. Turn the bulb assembly clockwise until seated.
7. Reverse the steps to reinstall the headlamp
assembly.
5-43
ProCarManuals.com

Taillamps, Turn Signal, Stoplamps
and Back-up Lamps
To replace one of these bulbs:
A. Taillamp/Stoplamp
B. Turn Signal Lamp
C. Back-up Lamp
1. Open the liftgate.2. Remove the two screws holding in the taillamp
assembly.
3. Slide the taillamp assembly rearward and away
from the vehicle.
4. Turn the bulb socket being replaced
counterclockwise to disconnect it.
5. Pull the bulb out of the bulb socket.
6. Push the new bulb into the bulb socket.
7. Reverse Steps 2 through 4 to reinstall the taillamp
assembly.
5-44
ProCarManuals.com

License Plate Lamp
To replace one of these bulbs:
1. Remove the two screws holding each of the license
plate lamps to the fascia.
2. Turn and pull the license plate lamp forward
through the fascia opening.3. Turn the bulb socket counterclockwise and pull the
bulb straight out of the socket.
4. Install the new bulb.
5. Reverse Steps 1 through 3 to reinstall the license
plate lamp.
Replacement Bulbs
Exterior Lamp Bulb Number
Back-up Lamp 3156
Front Turn Signal/Parking 3157K
Headlamps
High-beam 9005 or HB3
Low-beam/DRL 9006 or HB4
Rear Turn Signal, Stoplamp and
Taillamp3057
For replacement bulbs not listed here, contact your
dealer/retailer.
5-45
ProCarManuals.com

The sealant cannot seal sidewall damage, large
punctures, or a tire that has become unseated from
the wheel. SeeRoadside Assistance Program on
page 7-6.
Do not remove any objects that have penetrated
the tire.
3. Place the tire sealant and compressor kit on the
ground and unwrap the sealant/air hose (G) from
the side of the compressor.
4. Remove the valve stem cap from the at tire by
turning it counterclockwise.
5. Attach the sealant/air hose (G) onto the tire valve
stem. Turn it clockwise until it is tight.
Make sure the sealant and compressor kit on/off
switch (D) is in the O (off) position.
6. Remove the air compressor accessory plug (C)
from the unit.
7. Plug the air compressor accessory plug (C) into an
accessory power outlet in the vehicle. SeeAccessory
Power Outlet(s) on page 3-17for more information.
Do not slam door or close window on the
compressor accessory plug cord.
{CAUTION:
Idling the engine in a closed-in place or with
the climate control system off can cause
deadly carbon monoxide (CO). SeeEngine
Exhaust on page 2-29.
8. Start the vehicle. SeeStarting the Engine
(Automatic Engine Start/Stop) on page 2-18
for more information. The vehicle must be
running while using the air compressor.
{CAUTION:
Overination could cause the tire to rupture,
and you or others could be injured. Be sure to
read the inator instructions, and inate the
tire to its recommended pressure. Do not
exceed 36 psi (248 kPa).
5-72
ProCarManuals.com

9. Push the On/Off switch (D) to the I (on) position.
The tire sealant and compressor kit will inject
sealant and air into the tire.
The pressure gage (E) will initially show a high
pressure while the compressor pushes the sealant
into the tire. Once the sealant is completely
dispersed into the tire, the pressure will quickly drop
and start to rise again as the tire inates with air only.
10. Inate the tire to the recommended ination
pressure using the air pressure gage (E) on the top
of the unit. The recommended ination pressure
can be found on the Tire and Loading Information
label. SeeInflation - Tire Pressure on page 5-52.
The pressure gage reading is slightly high while the
compressor is on. Turn the compressor off to get
an accurate reading. The compressor may be turned
on and off until the correct pressure is reached.
Notice:If the recommended pressure cannot be
reached after 15 minutes, the vehicle should not
be driven farther. Damage to the tire is severe and
the sealant will not be effective. Remove the air
compressor plug from the accessory power outlet
and unscrew the inating hose from the tire
valve. SeeRoadside Assistance Program on
page 7-6for more information.11. Turn the compressor off by pushing the On/Off
switch (D) to the O (off) position.
Steps 12 through 20 must be done immediately
after Step 11.
The tire is not sealed and will continue to leak
air until the vehicle is driven and the sealant
is distributed in the tire.
Be careful while handling the tire sealant and
compressor kit as they could be hot after usage.
12. Unplug the air compressor accessory plug (C) from
the accessory power outlet in the vehicle.
13. Disconnect the sealant/air hose (G) from the tire
valve stem by turning it counterclockwise and
replace the tire valve stem cap.
14. Wrap the sealant/air hose (G) around the air
compressor channel to stow it in its original location.
15. Stow the air compressor accessory plug (C) back
in the air compressor. To do this, wrap the air
compressor accessory plug, snap in the plug, and
then push in the bottom and then the top of the
wrapped air compressor accessory plug.
5-73
ProCarManuals.com

16. If the at tire was
able to inate to the
recommended ination
pressure, remove
the maximum speed
label from the sealant
canister (B).
17. Place it in a highly visible location such as the
inside of the upper left corner of the windshield
or to the face of the radio/clock.
The maximum speed label reminds you to drive
cautiously and not to exceed 55 mph (90 km/h) until
you have the damaged tire inspected and repaired.
{CAUTION:
Storing the tire sealant and compressor
kit or other equipment in the passenger
compartment of the vehicle could cause injury.
In a sudden stop or collision, loose equipment
could strike someone. Store the tire sealant
and compressor kit in its original location.
18. Return the equipment to its original storage location
in your vehicle.
19. Immediately drive the vehicle 5 miles (8 km) to
distribute the sealant evenly in the tire.
5-74
ProCarManuals.com