instrument panel SATURN VUE HYBRID 2009 Owner's Guide

Temperature Control:Turn
clockwise or counterclockwise to
increase or decrease the
temperature. Typically, the best
setting is near 75°F (23°C).
Choosing the coldest or warmest
temperature setting does not cause
the system to heat or cool any faster.
Air Delivery Mode Control:Turn
clockwise or counterclockwise
to change the direction of the
airow inside the vehicle.
Select from the following air delivery
modes:
H(Vent):Air is directed to the
instrument panel outlets.
)(Bi-Level):Air is divided
between the instrument panel and
the oor outlets.
6(Floor):Air is directed to the
oor outlets with some air directed to
the windshield. When this mode is
selected, the system turns the
recirculation mode off. Recirculation
mode cannot be selected while
in oor mode. This is to help prevent
window fogging.
-(Defog):This mode clears the
windows of fog or moisture. Air
is directed to the oor outlets, with
some air directed to the windshield
and side window outlets. In this
mode, the system turns the
recirculation mode off and runs the
air conditioning compressor
unless the outside air is at or below
freezing. Recirculation mode
cannot be selected while in defog
mode. This helps prevent window
fogging.
0(Defrost):This mode removes
fog or frost from the windshield
more quickly. Air is directed to the
windshield, with some air directed to
the side window outlets and the
oor outlets. In this mode, the
system turns the recirculation mode
off automatically and runs the air
conditioning compressor unless the
outside air is at or below freezing.
The recirculation mode cannot
be selected while in defrost mode.
This helps prevent window
fogging and moisture building up
inside the vehicle. In this mode, the
climate control system prevents
all automatic engine start/stop
operations. This ensures the best
defrost performance.
For best results, clear all snow and
ice from the windshield before
defrosting.
Instrument Panel 3-19
ProCarManuals.com

#(Normal Air Conditioning):
Press to turn the air conditioning
system on or off. An indicator
light comes on to show that the air
conditioning is on. Normal Air
Conditioning (A/C) can be selected
in any mode as long as the fan
is on and the outside air temperature
is above freezing. Normal A/C
cannot be selected at the same time
as Hybrid Air Conditioning (A/C).
A ashing indicator light indicates
that the air conditioning compressor
is currently not available.
When Normal A/C is selected, the
climate control system prevents
all automatic engine start/stop
operations. This will ensure the
cabin comfort is maintained.
See “Air Conditioning and Automatic
Engine Start/Stop” later in this
section.
N(Hybrid Air Conditioning):
Press to turn the Hybrid A/C system
on or off. An indicator light comes
on to show that Hybrid A/C is
on. Hybrid A/C can be selected inany mode, except defrost as long as
the fan is on and the outside air
temperature is above freezing.
Hybrid A/C cannot be selected at
the same time as the normal
air conditioning. A ashing indicator
light shows the air conditioning
compressor is not available.
The Hybrid A/C works to balance
fuel economy and air conditioning
comfort. When Hybrid A/C is used in
warm weather, the vehicle gets
better fuel economy by allowing
more frequent start/stops. For
additional cooling, select Normal
A/C. See “Air Conditioning and
Automatic Engine Start/Stop” later in
this section.
@(Recirculation):Press to
toggle between the recirculation and
outside air modes. The indicator
light turns on when the recirculation
mode is selected. This mode can
be used to prevent outside air
and odors from entering the vehicle
or to help cool the air inside the
vehicle more quickly. Avoid usingthe recirculation mode during high
periods of humidity and cool outside
temperatures since this may
result in increased window fogging.
If window fogging is experienced,
select the defrost mode.
Recirculation mode is not available
in oor, defog or defrost modes.
If the button is selected in
these modes, the indicator will ash.
This helps prevent window fogging
and moisture building up inside
the vehicle.
Rear Window Defogger
The rear window defogger uses a
warming grid to remove fog from the
rear window.
The rear window defogger will only
work when the ignition is in
ON/RUN.
<(Rear Window Defogger):
Press to turn the rear window
defogger on or off. An indicator light
on the button comes on to show
that it is activated.
3-20 Instrument Panel
ProCarManuals.com

The rear window defogger stays on
for about 10 minutes if the vehicle
remains at slower vehicle speeds or
until the button is pressed, or
unless the ignition is turned to
ACC/ACCESSORY or LOCK/OFF. If
turned on again, the defogger
only runs for about ve minutes
before turning off again. At higher
vehicle speeds, the defogger
may stay on continuously. The
defogger can also be turned off by
turning off the ignition.
Notice:Do not use anything
sharp on the inside of the rear
window. If you do, you could cut
or damage the warming grid, and
the repairs would not be covered
by the vehicle warranty. Do not
attach a temporary vehicle
license, tape, a decal or anything
similar to the defogger grid.Air Conditioning and Engine
Start/Stop
On hot days, use the automatic fan
and automatic air delivery mode
settings and the vehicle will reach
the desired temperature more
quickly. The desired fan and air
delivery mode settings can still be
adjusted manually. Open the
windows to let the hot inside air
escape, then close them. This helps
reduce the time it takes for the
vehicle to cool down and helps the
system to operate more efficiently.
When either the Normal A/C or
Hybrid A/C modes are active, the air
conditioning system removes
moisture from the air, so a small
amount of water may drip under the
vehicle while idling or after turning
off the engine. This is normal.
The use of Normal A/C causes the
engine to keep running while
the vehicle is at a complete stop to
allow the climate control system
to continue cooling.The use of Hybrid A/C allows
automatic engine start/stop
operations while the vehicle is at a
complete stop. The air conditioning
compressor can not run when
the engine is not running, resulting
in reduced cooling performance.
The climate control system
may keep the engine running or
restart the engine during a stop to
continue cooling. Selecting the
Normal A/C button forces the engine
and air conditioning compressor
to restart automatically. For
more information about Engine
Start/Stop operation, seeStarting
the Engine (Automatic Engine
Start/Stop) on page 2-15.
Instrument Panel 3-21
ProCarManuals.com

Outlet Adjustment
Use the louvers located on the air
outlets to change the direction of the
airow.
Operation Tips
Clear away any ice, snow, or
leaves from the air inlets at
the base of the vehicle that may
block the ow of air into the
vehicle.
Do not use any non-GM
approved hood deectors that
could adversely affect the
performance of the system.
Keep the path under the front
seats clear of objects to help
circulate the air inside of
the vehicle more effectively.
Warning Lights,
Gages, and Indicators
Warning lights and gages can
signal that something is wrong
before it becomes serious enough
to cause an expensive repair or
replacement. Paying attention to the
warning lights and gages could
prevent injury.
Warning lights come on when there
may be or is a problem with one
of the vehicle’s functions. Some
warning lights come on briey when
the engine is started to indicate
they are working.Gages can indicate when there may
be or is a problem with one of the
vehicle’s functions. Often gages and
warning lights work together to
indicate a problem with the vehicle.
When one of the warning lights
comes on and stays on while
driving, or when one of the gages
shows there may be a problem,
check the section that explains what
to do. Follow this manual’s advice.
Waiting to do repairs can be
costly and even dangerous.
3-22 Instrument Panel
ProCarManuals.com

Instrument Panel Cluster
The instrument panel cluster is designed to indicate how the vehicle is running. It shows how fast the vehicle is
going, about how much fuel the vehicle has left and many other things needed to drive safely and economically.United States cluster, Canada similar
Instrument Panel 3-23
ProCarManuals.com

Speedometer and
Odometer
The speedometer shows the
vehicle’s speed in both miles
per hour (mph) and kilometers
per hour (km/h).
The odometer shows how far the
vehicle has been driven, in
either miles or kilometers.
If the vehicle needs a new odometer
installed, the new one is set to
the mileage total of the old
odometer. If it cannot, it will be set
at zero and a label must be put
on the driver’s door to show the old
mileage reading when the new
odometer was installed. If the
mileage is unknown, the label
should then indicate that the
previous mileage is unknown.
Trip Odometer
The trip odometer is located on the
instrument panel and shows how
far the vehicle has been driven since
the trip odometer was last reset.
To reset the trip odometer to zero,
press and hold the trip/reset
button on the speedometer for
about two seconds. Press the
trip/reset button to switch between
the trip odometer and odometer.
Tachometer
The tachometer displays the
engine speed in revolutions
per minute (rpm).The auto stop indicator is located at
the bottom of the tachometer. For
more information seeAuto Stop
Mode on page 3-35.
Safety Belt Reminders
Driver Safety Belt Reminder
Light
When the engine is started, a chime
sounds for several seconds to
remind the driver to fasten their
safety belt, unless it is already
buckled.
The safety belt light comes on and
stays on for several seconds,
then ashes for several more.
This chime and light are repeated if
the driver safety belt remains
unbuckled and the vehicle is in
motion. If the driver safety belt is
already buckled, neither the
chime nor the light comes on. U.S. shown, Canada similar
3-24 Instrument Panel
ProCarManuals.com

Passenger Safety Belt
Reminder Light
Several seconds after the engine
is started, a chime sounds for
several seconds to remind the front
passenger to buckle their safety belt.
This only occurs if the passenger
airbag is enabled. SeePassenger
Sensing System on page 1-49for
more information. The passenger
safety belt light, located on the
instrument panel, comes on and
stays on for several seconds and
then ashes for several more.
This chime and light are repeated if
the passenger remains unbuckled
and the vehicle is in motion.
If the passenger safety belt is
buckled before the engine is started,
neither the chime nor the light
comes on.The front passenger safety belt
warning light and chime may turn on
if an object is put on the seat
such as a briefcase, handbag,
grocery bag, laptop or other
electronic device. To turn off the
warning light and or chime, remove
the object from the seat or buckle
the safety belt.
Airbag Readiness Light
There is an airbag readiness light on
the instrument panel cluster,
which shows the airbag symbol. The
system checks the airbag’s
electrical system for malfunctions.
The light indicates if there is an
electrical problem. The system
check includes the airbag sensor,
the pretensioners, the airbag
modules, the wiring and the crash
sensing and diagnostic module.
For more information on the airbag
system, seeAirbag System on
page 1-41.
{CAUTION
If the airbag readiness light stays
on after the vehicle is started or
comes on while driving, it means
the airbag system might not be
working properly. The airbags in
the vehicle might not inate in a
crash, or they could even inate
without a crash. To help avoid
injury, have the vehicle serviced
right away.
The airbag readiness light comes on
when the vehicle is started, and
ashes for a few seconds. The light
goes out when the system is ready.
Instrument Panel 3-25
ProCarManuals.com

If the airbag readiness light stays on
after the vehicle is started or
comes on while driving, the airbag
system may not work properly. Have
the vehicle serviced right away.
The airbag readiness light should
ash for a few seconds when
the engine is started. If the light
does not come on then, have it xed
immediately. If there is a problem
with the airbag system, an
airbag Driver Information Center
(DIC) message may also come on.
SeeDIC Warnings and Messages
on page 3-42for more information.Passenger Airbag Status
Indicator
The vehicle has the passenger
sensing system. SeePassenger
Sensing System on page 1-49
for important safety information. The
instrument panel has a passenger
airbag status indicator.
When the vehicle is started, the
passenger airbag status indicator
will light ON and OFF, or the symbol
for on and off, for several seconds
as a system check. Then, after
several more seconds, the status
indicator will light either ON or OFF,or either the on or off symbol to let
you know the status of the right
front passenger frontal and
seat-mounted side impact airbags.
If the word ON or the on symbol
is lit on the passenger airbag status
indicator, it means that the right
front passenger frontal airbag and
seat-mounted side impact airbag are
enabled (may inate).
If the word OFF or the off symbol is
lit on the airbag status indicator,
it means that the passenger sensing
system has turned off the right
front passenger frontal airbag and
seat-mounted side impact airbag.
If, after several seconds, both status
indicator lights remain on, or if
there are no lights at all, there may
be a problem with the lights or
the passenger sensing system. See
your dealer/retailer for service. United States
Canada
3-26 Instrument Panel
ProCarManuals.com

{CAUTION
If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away.
SeeAirbag Readiness Light on
page 3-25for more information,
including important safety
information.
Charging System Light
The charging system light comes on
briey when the ignition is turned
on, but the engine is not running, as
a check to show the light is
working. It should go out when the
engine is started.If the light stays on, or comes on
while driving, there could be a
problem with the electrical charging
system. Have it checked by your
dealer/retailer. Driving while this light
is on could drain the battery.
If a short distance must be driven
with the light on, be sure to turn off
all accessories, such as the
radio and air conditioner.
Brake System Warning
Light
The brake indicator light should
come on briey as the engine
is started. If it does not come on
have the vehicle serviced by
your dealer/retailer.
When the ignition is on, the brake
system warning light comes on
when the parking brake is set. Thelight stays on if the parking brake
does not fully release. If it stays on
after the parking brake is fully
released, there is a brake problem.
Have the brake system inspected
immediately.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on. Driving
with the brake system warning
light on can lead to a crash. If the
light is still on after the vehicle
has been pulled off the road and
carefully stopped, have the
vehicle towed for service.
If the light comes on while driving, a
chime sounds. Pull off the road and
stop. The pedal might be harder to
push or go closer to the oor. It might
also take longer to stop. If the light is
still on, have the vehicle towed for
service. SeeTowing Your Vehicle on
page 4-22.
United StatesCanada
Instrument Panel 3-27
ProCarManuals.com

Antilock Brake System
(ABS) Warning Light
For vehicles with the Antilock Brake
System (ABS), this light should
come on briey as the engine
is started. If it does not come on
have the vehicle serviced by
your dealer/retailer.
If the ABS light stays on longer than
a few seconds after engine is
started, or comes on and stays on
while driving, try resetting the
system. To reset the system:
1. While driving, pull over when it is
safe to do so.
2. Place the vehicle in P (PARK).
3. Turn off the ignition.
4. Then restart the engine.If the ABS light remains on after
resetting the system or comes
on again while driving, the vehicle
needs service. If the ABS light is on,
but the regular brake system
warning light is not on, the antilock
brakes are not working properly,
but the regular brakes are still
functioning. Have the vehicle
serviced right away. If both brake
lights are on, the vehicle does
not have antilock brakes, and there
is a problem with the regular
brakes as well. Have the vehicle
towed for service. SeeTowing Your
Vehicle on page 4-22.
StabiliTrak®/Traction
Control System (TCS)
Warning Light
The Traction Control System
(TCS)/StabiliTrak®system warning
light comes on briey as the
engine is started.
If it does not, have the vehicle
serviced by your dealer/retailer. If
the system is working normally
the indicator lights go off.
This light ashes while the Traction
Control System (TCS) and/or the
StabiliTrak system are working.
It also ashes when the Antilock
Brake System (ABS) is activated.
If the light comes on and stays
on while driving there is a problem
with the Traction Control System
(TCS) or the StabiliTrak system. The
3-28 Instrument Panel
ProCarManuals.com