clock Seat Alhambra 2005 Owner's Manual

Instrument panel45
Safety FirstControls and equipment Tips and Maintenance Technical Data
In some model versions or in certain countries, it is possible to
insert the ignition key and have the dash panel lights go on
without switching the engine on. This function is independent of
the vehicle's light connections.
Arrangement of instruments depends on the model and the engine
fitted.
1Oil temperature indicator* . . . . . . . . . . . . . . . . . . . . . . . . . 46
2Revolutions counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3Digital clock* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Outside temperature indicator* . . . . . . . . . . . . . . . . . . . . . 46
Multi-function indicator* . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4Coolant temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5Warning lamps display/selector lever positions*
(automaticgear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
7Mileage clock with Service interval indicator* . . . . . . . . . .52
8Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ADigital clock knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
BTrip mileage clock/Reset service Interval indicator . . . . . . 52K
I In
ns
st
tr
ru
um
me
en
nt
ts
s
Instrument overview
Fig. 46
1/ 2
0
1/190
6012 0
0 2
15
6 4
7
81/ m i n
x1000
3
0 20 40608010 0
14 0
18 0
220
260
30507090
12 0
16 0
200
240
Km/h1
8888888888.8service
k/miles88:88
EPC
14
2
5
8
96
A37B
!
AL0-070

Instrument panel46
Temperature of the engine oil*
Do not demand full performance from the engine when the engine
oil is cold. If in exceptional conditions the indicator is in the upper
area, reduce the revolutions. The needle should return to the
normal range.
If the needle remains in the upper zone, stop the vehicle and turn
the engine off. Check the oil level in the engine. If the oil level is
correct and the oil pressure pilot lamp does not switch off when
you turn the engine on, drive to the nearest Technical Service
Centre, avoiding high revolutions.
K
Revolutions counter*
On no account must the revolutions counter needle move into the
red zone of the scale.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
Changing up in good time helps to save fuel and keep the noise down.
Change down a gear at the latest when the engine turn over is no
longer smooth.
Avoid high engine revolutions during the running-in period.
K
Digital clock*
To set the digital clock turn knob Alocated on the lower left next
to the rev counter.
• The hours are set by turning the button anti-clockwise until it
stops. By turning the knob once, you move forward one hour. By
turning and holding the knob, the hours move forward
continuously.
• The minutes are set by turning the button clockwise until it stops.
By turning the knob once, you move forward one minute. By
turning and holding the knob, the minutes move forward
continuously.
The knob can be used to set the clock to the exact second.
• Turn the knob to the right until the time is set to exactly one
minute before the required time.
• Turn the button to the right just as the seconds indicator of an
accurately set clock shows one full minute.
Turning the button to the left sets the clock to the required arrow.
K
Outside temperature indicator*
The outside temperature is displayed when the ignition is on.
At temperatures from +5°C to –5°C, a snowflake symbol is
displayed along with the temperature.
The snowflake symbol is to warn the driver to take extra care when
there is a risk of ice forming on the road.


Instrument panel48
If you press the upper part of the button, the different functions will
appear consecutively.
If you press the lower part of the button, the functions will appear
in the opposite direction.
The following data can be obtained in this order by the memory:
• Driving time
• Km driven
• Average speed
• Average fuel consumption
The instantaneous fuel consumption will not be memorized but will
always appear in an updated version.
M Me
em
mo
or
ry
y
Two automaticmemories are fitted:
T Th
he
e iin
nd
di
iv
vi
id
du
ua
al
l mme
em
mo
or
ry
y ((M
Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 11)
)
collects the
following data while ignition is on: driving time, kms driven and
fuel consumption.
The calculation of the average speed and average consumption is
based on this data.
If the trip resumes within the 2 following hours from switching off
ignition the new data will be added to the one already memorized.
If the interruption is longer than 2 hours, all data will automatically
be deleted from the memory.T Th
he
e ggl
lo
ob
ba
al
l mme
em
mo
or
ry
y ((M
Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 22)
)
collects all data
from all trips up to 100 driving hours, 10,000 km and 1,000 liters
of fuel consumption. This data is used to calculate the average
speed and average consumption for all individual trips.
In case one of these values is exceeded, the memory is deleted
and a new count starts. As opposed to the individual memory, the
global memory will not be deleted if the trip is interrupted for more
than 2 hours.
T To
o cco
on
ns
su
ul
lt
t
data select the respective memory by pressing the
"Reset"
⇒fig. 48Abutton on the windscreen wiper lever.
The digital clock display will indicate the memory which was
selected:
M Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 11 ––
(Individual memory)
M Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 22 ––
(Global memory)
D De
el
le
et
te
e mme
em
mo
or
ri
ie
es
s
If you press the "Reset"
⇒fig. 48Abutton for more than two
seconds the selected memory will be deleted.
If the battery of the vehicle is disconnected both memories will be
deleted.
V Vi
is
su
ua
al
li
iz
ze
ed
d iin
nf
fo
or
rm
ma
at
ti
io
on
n
When the ignition is switched on the last selected function or the
outside temperature with the ice symbol (warning for icy road) will
appear on the display.


Instrument panel49
Safety FirstControls and equipment Tips and Maintenance Technical Data
N No
o ssy
ym
mb
bo
ol
l -- TTi
im
me
e
The time appears even if the ignition is switched off.
The clock is set by turning the button next to the rev counter in the
instrument panel
⇒page 46 "Digital clock".
° °C
C -- OOu
ut
ts
si
id
de
e tte
em
mp
pe
er
ra
at
tu
ur
re
e
The temperature range goes from –40°C to +58°C. If the car is
stationary or if driving at slow speed the indicated temperature
may be slightly higher than the real temperature due to engine
heat.
If the outside temperature is between +4°C and –7°C the ice
symbol will appear on the display (warning for icy road).
This symbol will flash at first for about 5 seconds and then remain
lit while the outside temperature is not above +4°C or below –7°C.
W Wh
he
en
n tth
he
e ssy
ym
mb
bo
ol
l ffo
or
r iic
cy
y rro
oa
ad
ds
s aap
pp
pe
ea
ar
rs
s tth
he
e mmu
ul
lt
ti
i-
-f
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r
a au
ut
to
om
ma
at
ti
ic
ca
al
ll
ly
y iin
nd
di
ic
ca
at
te
es
s tth
he
e oou
ut
ts
si
id
de
e tte
em
mp
pe
er
ra
at
tu
ur
re
e ((w
wa
ar
rn
ni
in
ng
g ffo
or
r iic
cy
y
r ro
oa
ad
ds
s)
),
, rre
eg
ga
ar
rd
dl
le
es
ss
s oof
f tth
he
e sse
el
le
ec
ct
te
ed
d ffu
un
nc
ct
ti
io
on
n.
.If you wish to see the previously selected function press the
⇒fig.
48Bbutton on the windscreen wiper lever.
l l/
/1
10
00
0 kkm
m -- IIn
ns
st
ta
an
nt
ta
an
ne
eo
ou
us
s ffu
ue
el
l cco
on
ns
su
um
mp
pt
ti
io
on
n
Instantaneous consumption is shown in l/100 km. The computer
calculates the consumption every 30 meters. When the vehicle is
stationary the computer will display the last value in the memory.
On some models, the display will show fuel consumption in
ltr/hour when the vehicle is in a stationary position with the engine
running.
If the instantaneous consumption display is selected when the
engine is started, the computer will indicate the average
consumption for the first 30 to 40 meters.
You can use this display to adjust your driving style to the desired
fuel consumption.
Ø Ø ll/
/1
10
00
0 kkm
m -- AAv
ve
er
ra
ag
ge
e ffu
ue
el
l cco
on
ns
su
um
mp
pt
ti
io
on
n
This mode shows the average fuel consumption only and not the
consumption at the time of reading.
Once the memory is deleted the display will show the average
consumption after approximately 30 meters. Until then, the display
will show dashes instead of the value. The value is updated
throughout the trip every 5 seconds.
If you select the individual memory( (M
Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 11)
)
the
average consumption of a particular trip is displayed.

I In
n cca
as
se
e tth
hi
is
s ssy
ym
mb
bo
ol
l iis
s uus
se
ed
d aas
s aan
n iin
nd
di
ic
ca
at
ti
io
on
n ffo
or
r iic
cy
y rro
oa
ad
ds
s,
, kke
ee
ep
p iin
n mmi
in
nd
d tth
ha
at
t
t th
he
e rro
oa
ad
d mma
ay
y cco
on
nt
ti
in
nu
ue
e tto
o bbe
e iic
cy
y eev
ve
en
n iif
f tth
he
e tte
em
mp
pe
er
ra
at
tu
ur
re
e iis
s aar
ro
ou
un
nd
d ++4
4°
°C
C.
.
W
WA
AR
RN
NI
IN
NG
G

Instrument panel52
Mileage clock/Trip mileage
The upper counter registers the total distance driven and the lower
one the short trips.
The last figure of the lower counter indicates 100 m.
The trip mileage can be put back to zero by pressing the reset knob
⇒fig. 46Bnext to the speedometer.K
Service interval indicator*
If a service is due, the word "Service" will flash for about 20
seconds when the engine is switched on, the vehicle is not moving
and the mileage clock reset button is not touched.
The deadline for any service will be displayed 3,000 km in
advance.
• • IIn
nt
te
er
rm
mi
it
tt
te
en
nt
t sse
er
rv
vi
ic
ce
e*
* ffo
or
r 220
0 sse
ec
co
on
nd
ds
s
. Indicates that the time for a
new service has elapsed.
• • SSe
er
rv
vi
ic
ce
e KKm
m 33,
,0
00
00
0*
* ffo
or
r 220
0 sse
ec
co
on
nd
ds
s
. Indicates that the next service
is due in 3,000 km. Every 100 km the number of km will decrease
by 100 km up to the indication "Service".
A Af
ft
te
er
r tth
he
e sse
er
rv
vi
ic
ce
e hha
as
s bbe
ee
en
n ppe
er
rf
fo
or
rm
me
ed
d tth
he
e ddi
is
sp
pl
la
ay
y nne
ee
ed
ds
s tto
o bbe
e
r re
es
se
et
t.
.
The display will be reset by a Technical Service Centre as follows:
• With the ignition switched off, press and hold the trip meter reset
button below the speedometer.• Switch ignition on and release the reset button. The display will
show the next service.
• Turn the minute button of the digital clock to the right.
• Switch ignition off. Now the service indicator has been set to
zero.
T Th
he
e sse
er
rv
vi
ic
ce
e iin
nd
di
ic
ca
at
to
or
r cca
an
nn
no
ot
t bbe
e cco
om
mp
pl
le
et
te
el
ly
y sse
et
t tto
o zze
er
ro
o.
. IIt
t cca
an
n oon
nl
ly
y
b be
e sse
et
t tto
o 115
5,
,0
00
00
0 kkm
m.
.
N No
ot
te
e• Do not zero the display between the Service intervals. Otherwise an
incorrect reading will be shown.
• If the battery is disconnected the details in the service displayare
retained.
• If the instrument panel changes due to repair, the service interval display
must be reset. This should be carried out by a Technical Service Centre.
Should the display not be reprogrammed, then the service work should be
carried out in accordance with the Inspection and Maintenance Plan and not
according to the Service Interval Display. The Service interval indicator only
becomes valid again after carrying out an inspection and resetting the
indicator.
F Fa
au
ul
lt
t iin
nd
di
ic
ca
at
to
or
r
If a failure occurs, "FAIL" would appear either on the instrument
panel or the trip meter. The defect should be repaired by a
Technical Service Centre as soon as possible.
K

Instrument panel53
Safety FirstControls and equipment Tips and Maintenance Technical Data
Speedometer
The speedometer is fitted with a digital mileage clock and a trip
mileage clock as well as a service interval indicator* and outside
temperature*.
During the running-in period the instructions in the chapter "The
first 1,500 kilometres and afterwards" should be noted.
K
Voltmeter
The voltmeter shows the voltage of the vehicle’s electrical
installation. T Th
he
e nno
or
rm
ma
al
l rre
ea
ad
di
in
ng
g lli
ie
es
s bbe
et
tw
we
ee
en
n 112
2 aan
nd
d 115
5 VV.
. IIf
f tth
he
e
v vo
ol
lt
ta
ag
ge
e ffa
al
ll
ls
s bbe
el
lo
ow
w 112
2 VV wwi
it
th
h tth
he
e een
ng
gi
in
ne
e rru
un
nn
ni
in
ng
g,
, hha
av
ve
e tth
he
e ppo
ow
we
er
r
s su
up
pp
pl
ly
y ((b
ba
at
tt
te
er
ry
y aan
nd
d gge
en
ne
er
ra
at
to
or
r)
) cch
he
ec
ck
ke
ed
d aat
t aa TTe
ec
ch
hn
ni
ic
ca
al
l SSe
er
rv
vi
ic
ce
e
C Ce
en
nt
tr
re
e
⇒"
"W
Wa
ar
rn
ni
in
ng
g lla
am
mp
ps
s"
" cch
ha
ap
pt
te
er
r.
.
During engine starting the voltage can fall below 8 V.
K
220
260
240
88
AL0-074Fig. 51

Opening and closing80
Switching off the alarm
To switch off the alarm, unlock the car doors.
N No
ot
te
e
• If once the alarm signals have ended you try to gain access to any other
security area (for instance, by opening the tailgate/boot after having
opened a door) the alarm signal will be triggered again.
• The alarm system can be switched on or off with the radio-frequency*
remote control. You will find more details on handling in the "Radio-
frequency remote control" chapter.
P Pa
as
ss
se
en
ng
ge
er
r cco
om
mp
pa
ar
rt
tm
me
en
nt
t ssu
ur
rv
ve
ei
il
ll
la
an
nc
ce
e aac
ct
ti
iv
va
at
ti
io
on
n*
*
When switching on the anti-theft alarm system the passenger
compartment surveillance is also activated.If there is any movement in the car interior when the interior
monitoring system is activated, the anti-theft alarm will be
triggered.
N No
ot
te
e
Please bear in mind warnings on page 75.
S
Se
en
ns
so
or
rs
s
The passenger compartment surveillance sensors are located at
the upper part of the pillars between the front and the backseat
doors.
In order to avoid interfering with their proper performance you
must never cover the sensors.
N No
ot
te
e
If the car is parked for long periods, after 14 days the warning led will switch
off to avoid the battery being discharged. The alarm system will remain
activated.
I In
nt
te
er
rr
ru
up
pt
ti
in
ng
g tth
he
e aal
la
ar
rm
m ttr
ri
ig
gg
ge
er
r
To interrupt the triggering of the alarm you must turn the key in the
lock clockwise or press the open
⇒ fig. 681button on the remote
control.
N No
ot
te
e
l If the alarm has been triggered the driver will notice it because the led on
the driver’s door will blink in a different way to that of alarm on.K
Fig. 66AL0-081

190Checking and refilling
C
Ca
au
ut
ti
io
on
n
• Only our G12+ (purple colour) should be used as an antifreeze additive.
Observe the notice on the container. The cooling liquid may be purchased in
Technical Services.
• The antifreeze additive G12+ can be mixed with other additives (G11 and
G12).
• The additive G12 (red colour) should never be mixed with G11.
K
Checking coolant level
The level can only be checked properly when the engine is not
running.
The coolant level must be between the
m ma
ax
xand m
mi
in
nmarks on the
expansion tank when engine is cold and can be slightly above the
m ma
ax
xmark when it is warm.K
Coolant losses
Coolant loss normally indicates leaks in the system. In this case
the cooling system should be checked by a Technical Service
Center without delay. It is not sufficient merely to add coolant.
In a sealed system losses can only occur if the boiling point of the
coolant is exceeded as a result of overheating, and coolant is
forced out of the system.
K
Topping up coolant
Switch engine off and let it cool down. Then cover expansion tank
cap with a cloth and turn cap carefully anti-clockwise and remove.
No other coolant may be used if
G G1
12
2+
+is not available. In this
case only water can be used and the correct mixture concentration
must be restored with the specified coolant additive (see previous
page) as soon as possible.
Fig. 160
N Ne
ev
ve
er
r oop
pe
en
n tth
he
e bbo
on
nn
ne
et
t iif
f yyo
ou
u cca
an
n sse
ee
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t lle
ea
av
vi
in
ng
g tth
he
e een
ng
gi
in
ne
e
c co
om
mp
pa
ar
rt
tm
me
en
nt
t –– RRi
is
sk
k oof
f ssc
ca
al
ld
di
in
ng
g!
! WWa
ai
it
t uun
nt
ti
il
l nno
o mmo
or
re
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t cca
an
n
b be
e sse
ee
en
n.
.
W
WA
AR
RN
NI
IN
NG
G
D Do
o nno
ot
t rre
em
mo
ov
ve
e eex
xp
pa
an
ns
si
io
on
n tta
an
nk
k cca
ap
p wwh
he
en
n een
ng
gi
in
ne
e iis
s hho
ot
t –– dda
an
ng
ge
er
r oof
f
s sc
ca
al
ld
di
in
ng
g:
:
S Sy
ys
st
te
em
m iis
s uun
nd
de
er
r ppr
re
es
ss
su
ur
re
e.
.
W
WA
AR
RN
NI
IN
NG
G

AL0-046

196Checking and refilling
• Check acid level of the battery⇒"Battery chapter". Depending
on the technique used while charging battery acid could
vaporize.
K
If the battery is disconnected and then reconnected...
P Pl
le
ea
as
se
e nno
ot
te
e tth
he
e wwa
ar
rn
ni
in
ng
gs
s ffr
ro
om
m tth
he
e ""E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r
a an
nd
d ffo
ol
ll
lo
ow
wi
in
ng
g oon
ne
es
s,
, bbe
ef
fo
or
re
e uun
nd
de
er
rg
go
oi
in
ng
g aan
ny
y wwo
or
rk
k oon
n tth
he
e een
ng
gi
in
ne
e oor
r
e en
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t.
.
After d di
is
sc
co
on
nn
ne
ec
ct
ti
in
ng
g
or charging the battery you should:
To reset the clock
⇒"Instruments" chapter.
Switch on again the automatic opening and closing of the power
windows
⇒"Electrical powered windows" chapter.
Should you have problems with the starting or idling of a petrol
engine start engine as follows: switch on ignition for approximately
30 seconds and switch off again. Start engine.
K
Change battery
Our batteries have been developed to suit their location and have
built-in safety elements. Original SEAT batteries comply with all
maintenance, performance and safety requirements for your
vehicle.
We recommend using a battery that does not require maintenance.
P Pl
le
ea
as
se
e nno
ot
te
e tth
he
e wwa
ar
rn
ni
in
ng
gs
s ffr
ro
om
m tth
he
e ""E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r
a an
nd
d ffo
ol
ll
lo
ow
wi
in
ng
g oon
ne
es
s,
, bbe
ef
fo
or
re
e uun
nd
de
er
rg
go
oi
in
ng
g aan
ny
y wwo
or
rk
k oon
n tth
he
e een
ng
gi
in
ne
e oor
r
e en
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t.
.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
Because of the problem of disposing of the old battery, the renewalshould
preferably done at a Technical Service Centre. Batteries contain, amongst
other things, sulphuric acid and lead and must on no account be putwith
normal household waste.
K

205 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
• Remove the rubber seal⇒ fig. 171Bon the eyelet upwards.
• Take the wheel spanner
⇒ fig. 171Cfrom the vehicle tools.
Place it as far as it will go over the bolt. Hold in this position and
press the locking ring
⇒ fig. 171Ddown.
• Turn the box spanner
Cto the left until it is supporting the
spare wheel, which issuspended from a steel cable
⇒ fig. 171.
• Squeeze the retainer lightly (arrows
1) and at the same time
fold the cross piece in the direction shown 2⇒ fig. 172. Now
guide the retainer through the central opening in the spare
wheel.
K
Installing spare wheel
• Stand the wheel behind the vehicle, as shown in the fig. 173.• Guide the retainer from the inner side of the wheel through the
spare wheel central opening.
• Fold the cross piece in the opposite to arrow
⇒ fig. 1722.
• Push the spare wheel under the vehicle with the outer side facing
down.
• Turn the bolt in the luggage compartment floor clockwise with
the wheel spanner to lift the wheel into the spare wheel bracket
under the vehicle. E En
ns
su
ur
re
e tth
ha
at
t tth
he
e ssp
pa
ar
re
e wwh
he
ee
el
l ffi
it
ts
s iin
nt
to
o tth
he
e rre
ec
ce
es
ss
s
( (a
ar
rr
ro
ow
ws
s)
) iin
n tth
he
e bbu
um
mp
pe
er
r
⇒ fig. 173.
• Turn the bolt (max. torque 25 Nm) until the spare wheel sits
firmly in the luggage compartment floor. Seal the opening with the
rubber seal and fold the cover back.
N No
ot
te
e
If you need to drive without a spare wheel, the spare wheel bracket,
together with the rope, must be fully wound up to the vehicle floor.K
W
Wh
he
ee
el
ls
s
General notes
• New tyres do not give maximum grip straight away and should
therefore be run in at moderate speeds and a careful style of
driving for about the first 100 km. This will help to make the tyres
last longer.

Fig. 173AL0-135