reset Seat Alhambra 2005 Owner's Manual
[x] Cancel search | Manufacturer: SEAT, Model Year: 2005, Model line: Alhambra, Model: Seat Alhambra 2005Pages: 272, PDF Size: 6.35 MB
Page 49 of 272
Instrument panel45
Safety FirstControls and equipment Tips and Maintenance Technical Data
In some model versions or in certain countries, it is possible to
insert the ignition key and have the dash panel lights go on
without switching the engine on. This function is independent of
the vehicle's light connections.
Arrangement of instruments depends on the model and the engine
fitted.
1Oil temperature indicator* . . . . . . . . . . . . . . . . . . . . . . . . . 46
2Revolutions counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3Digital clock* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Outside temperature indicator* . . . . . . . . . . . . . . . . . . . . . 46
Multi-function indicator* . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4Coolant temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5Warning lamps display/selector lever positions*
(automaticgear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
7Mileage clock with Service interval indicator* . . . . . . . . . .52
8Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ADigital clock knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
BTrip mileage clock/Reset service Interval indicator . . . . . . 52K
I In
ns
st
tr
ru
um
me
en
nt
ts
s
Instrument overview
Fig. 46
1/ 2
0
1/190
6012 0
0 2
15
6 4
7
81/ m i n
x1000
3
0 20 40608010 0
14 0
18 0
220
260
30507090
12 0
16 0
200
240
Km/h1
8888888888.8service
k/miles88:88
EPC
14
2
5
8
96
A37B
!
AL0-070
Page 52 of 272
Instrument panel48
If you press the upper part of the button, the different functions will
appear consecutively.
If you press the lower part of the button, the functions will appear
in the opposite direction.
The following data can be obtained in this order by the memory:
• Driving time
• Km driven
• Average speed
• Average fuel consumption
The instantaneous fuel consumption will not be memorized but will
always appear in an updated version.
M Me
em
mo
or
ry
y
Two automaticmemories are fitted:
T Th
he
e iin
nd
di
iv
vi
id
du
ua
al
l mme
em
mo
or
ry
y ((M
Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 11)
)
collects the
following data while ignition is on: driving time, kms driven and
fuel consumption.
The calculation of the average speed and average consumption is
based on this data.
If the trip resumes within the 2 following hours from switching off
ignition the new data will be added to the one already memorized.
If the interruption is longer than 2 hours, all data will automatically
be deleted from the memory.T Th
he
e ggl
lo
ob
ba
al
l mme
em
mo
or
ry
y ((M
Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 22)
)
collects all data
from all trips up to 100 driving hours, 10,000 km and 1,000 liters
of fuel consumption. This data is used to calculate the average
speed and average consumption for all individual trips.
In case one of these values is exceeded, the memory is deleted
and a new count starts. As opposed to the individual memory, the
global memory will not be deleted if the trip is interrupted for more
than 2 hours.
T To
o cco
on
ns
su
ul
lt
t
data select the respective memory by pressing the
"Reset"
⇒fig. 48Abutton on the windscreen wiper lever.
The digital clock display will indicate the memory which was
selected:
M Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 11 ––
(Individual memory)
M Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 22 ––
(Global memory)
D De
el
le
et
te
e mme
em
mo
or
ri
ie
es
s
If you press the "Reset"
⇒fig. 48Abutton for more than two
seconds the selected memory will be deleted.
If the battery of the vehicle is disconnected both memories will be
deleted.
V Vi
is
su
ua
al
li
iz
ze
ed
d iin
nf
fo
or
rm
ma
at
ti
io
on
n
When the ignition is switched on the last selected function or the
outside temperature with the ice symbol (warning for icy road) will
appear on the display.
Page 54 of 272
Instrument panel50
If you select the global memory( (M
Mu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 22)
)
the
average consumption for all individual trips is displayed
⇒"Global
memory".
N No
ot
te
e
The amount of used fuel will not be displayed.
k
km
m -- KKm
ms
s ddr
ri
iv
ve
en
n
I In
n tth
he
e MMu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 11 ppo
os
si
it
ti
io
on
n tth
he
e mme
em
mo
or
ry
y
displays the
kms driven since the ignition was switched on or since the memory
was deleted. See previous page "Individual memory".
I In
n tth
he
e MMu
ul
lt
ti
if
fu
un
nc
ct
ti
io
on
n iin
nd
di
ic
ca
at
to
or
r 22 ppo
os
si
it
ti
io
on
n tth
he
e mme
em
mo
or
ry
y
displays the
kms driven on all individual trips. See previous page "Global
memory".
The highest display for either position is 10,000 km. When this is
exceeded it will reset itself.
k km
m/
/h
h -- AAv
ve
er
ra
ag
ge
e ssp
pe
ee
ed
d
See chapter "Average fuel consumption".
D Dr
ri
iv
vi
in
ng
g tti
im
me
e
The same is valid for "driving time" as for "km driven". The
maximum time shown in the display is 99 hours and 59 minutes.
When this is exceeded it will reset itself.
K
Coolant temperature
The gauge starts to work when the ignition is switched on.
When the ignition is switched on the warning lamp
Cflashes for a
few seconds as a functional check.
AC Co
ol
ld
d
Avoid high engine speeds and do not work engine too hard yet.
BN No
or
rm
ma
al
l
When the vehicle is driven normally the needle should settle down
in the central zone.
When engine is working hard and the ambient temperature is high,
the needle may move a long way up.
Fig. 49
1/ 2
0
1
/
90
6012 0
5
6
BA
CAL0-072
Page 56 of 272
Instrument panel52
Mileage clock/Trip mileage
The upper counter registers the total distance driven and the lower
one the short trips.
The last figure of the lower counter indicates 100 m.
The trip mileage can be put back to zero by pressing the reset knob
⇒fig. 46Bnext to the speedometer.K
Service interval indicator*
If a service is due, the word "Service" will flash for about 20
seconds when the engine is switched on, the vehicle is not moving
and the mileage clock reset button is not touched.
The deadline for any service will be displayed 3,000 km in
advance.
• • IIn
nt
te
er
rm
mi
it
tt
te
en
nt
t sse
er
rv
vi
ic
ce
e*
* ffo
or
r 220
0 sse
ec
co
on
nd
ds
s
. Indicates that the time for a
new service has elapsed.
• • SSe
er
rv
vi
ic
ce
e KKm
m 33,
,0
00
00
0*
* ffo
or
r 220
0 sse
ec
co
on
nd
ds
s
. Indicates that the next service
is due in 3,000 km. Every 100 km the number of km will decrease
by 100 km up to the indication "Service".
A Af
ft
te
er
r tth
he
e sse
er
rv
vi
ic
ce
e hha
as
s bbe
ee
en
n ppe
er
rf
fo
or
rm
me
ed
d tth
he
e ddi
is
sp
pl
la
ay
y nne
ee
ed
ds
s tto
o bbe
e
r re
es
se
et
t.
.
The display will be reset by a Technical Service Centre as follows:
• With the ignition switched off, press and hold the trip meter reset
button below the speedometer.• Switch ignition on and release the reset button. The display will
show the next service.
• Turn the minute button of the digital clock to the right.
• Switch ignition off. Now the service indicator has been set to
zero.
T Th
he
e sse
er
rv
vi
ic
ce
e iin
nd
di
ic
ca
at
to
or
r cca
an
nn
no
ot
t bbe
e cco
om
mp
pl
le
et
te
el
ly
y sse
et
t tto
o zze
er
ro
o.
. IIt
t cca
an
n oon
nl
ly
y
b be
e sse
et
t tto
o 115
5,
,0
00
00
0 kkm
m.
.
N No
ot
te
e• Do not zero the display between the Service intervals. Otherwise an
incorrect reading will be shown.
• If the battery is disconnected the details in the service displayare
retained.
• If the instrument panel changes due to repair, the service interval display
must be reset. This should be carried out by a Technical Service Centre.
Should the display not be reprogrammed, then the service work should be
carried out in accordance with the Inspection and Maintenance Plan and not
according to the Service Interval Display. The Service interval indicator only
becomes valid again after carrying out an inspection and resetting the
indicator.
F Fa
au
ul
lt
t iin
nd
di
ic
ca
at
to
or
r
If a failure occurs, "FAIL" would appear either on the instrument
panel or the trip meter. The defect should be repaired by a
Technical Service Centre as soon as possible.
K
Page 66 of 272
Instrument panel62
Windscreen washer fluid level*
This warning lamp will light up if the fluid level in the windscreen
washer container is too low.
Add water for the windscreen washers and headlight washers*
⇒
"Windscreen washer" chapter.K
Open door warning lamp*
This warning lamp will light up if any of the doors is open or not
properly closed.
K
Brake pad wear monitor*
The warning lamp will light up if the frontpads are worn out.
You should proceed immediately to a Technical Service Centre to
have the brake pads checked.
Since this warning lamp indicates the wear of the frontpads only,
it is advisable to have the rear brake pads checked at the same
time.
K
Engine oil pressure/level*
The warning lamp lights up for a few seconds as a functional check
when ignition is switched on.
If the warning lamp is red or yellow or flashes it indicates that the
engine oil pressure or level is too low. This warning lamp will also
light up if there is a defect in the oil level indicator.I If
f lli
ig
gh
ht
ts
s uup
p oor
r ffl
la
as
sh
he
es
s rre
ed
d ((i
in
ns
su
uf
ff
fi
ic
ci
ie
en
nt
t ooi
il
l ppr
re
es
ss
su
ur
re
e)
)
If the warning lamp lights up or flashes red while driving an
acoustic signal will sound three times at engine speeds above
1500 rpm. Stop and switch engine off: check oil level and add oil,
if necessary
⇒"Engine oil" chapter.
If the warning lamp flashes even though the oil level is in order, do
not continue driving. Do not even run the engine at idling speed.
Call in expert assistance.
If while driving the engine speed decreases below idling speed the
oil pressure warning lamp may light up. Increase engine speed by
accelerating or changing down gear.
L Li
ig
gh
ht
ts
s uup
p yye
el
ll
lo
ow
w ((o
oi
il
l lle
ev
ve
el
l*
* tto
oo
o llo
ow
w)
)
The yellow warning lamp indicates that the oil level is too low. Stop
engine and add oil
⇒"Engine oil" chapter.
When opening the bonnet the oil level warning is reset. However, if
you do not refill oil the warning will reappear after about 100 km.
F Fl
la
as
sh
he
es
s yye
el
ll
lo
ow
w ((d
de
ef
fe
ec
ct
ti
iv
ve
e ooi
il
l lle
ev
ve
el
l*
* iin
nd
di
ic
ca
at
to
or
r)
)
If the oil level indicator is defective an acoustic signal will sound
and the warning lamp will flash several times.
At the same time the onboard computer will display a warning for a
short time
⇒"Onboard computer" chapter. Take the vehicle to a
Technical Service Centre as soon as possible to have the engine
checked.
From the moment of the defect to the check-up of the engine the
oil level needs to be checked regularly, preferably when filling the
tank.
K
Page 159 of 272
Driving155
Safety FirstControls and equipment Tips and Maintenance Technical Data
This however, is not the case when the stored speed is exceeded
by more than 10 km/h for a period of more than 5 minutes. The
speed must then be stored again.
Altering stored speed
R Re
ed
du
uc
ci
in
ng
g/
/s
se
et
tt
ti
in
ng
g
The stored speed can be reduced by pressing button
⇒ fig. 147B.
By pressing button
⇒ fig. 147Bbriefly, the stored speed is
reduced by a preset amount. If you pres and hold the button, the
speed will decrease through automatic deceleration. The speed
reached when reducing the button will be stored.
If the button is released at a speed of less than approx. 30 km/h,
the memory is deleted. The speed must then, if necessary, be reset
using button
⇒ fig. 147Bafter the vehicle has accelerated to a
speed higher than approx. 30 km/h.
A Ac
cc
ce
el
le
er
ra
at
ti
in
ng
g/
/s
st
to
or
ri
in
ng
g
The stored speed can be increased without depressing the
accelerator by moving the slide control
⇒ fig. 147Ato R RE
ES
S
.
By briefly pressing the slide control, the speed is increased by a
preset amount. If the switch is moved to the left and held, thespeed is increased through automatic acceleration. The speed
reached when the switch is released is then saved.
K
Switching system off temporarily
V Ve
eh
hi
ic
cl
le
es
s wwi
it
th
h mma
an
nu
ua
al
l gge
ea
ar
rb
bo
ox
x:
:
T Th
he
e ssy
ys
st
te
em
m iis
s tte
em
mp
po
or
ra
ar
ri
il
ly
y ssw
wi
it
tc
ch
he
ed
d oof
ff
f
when the brake or clutch
pedals are used or when the switch
Ais moved to OFF (not
engaged).
The speed stored at this time will remain in the memory.
To r re
es
su
um
me
e
the previously stored speed push switch
Afully to the
left after the brake or clutch pedals are released.
T Th
he
e ppr
ro
og
gr
ra
am
mm
me
ed
d ssp
pe
ee
ed
d mmu
us
st
t oon
nl
ly
y bbe
e rre
es
su
um
me
ed
d wwh
he
en
n iit
t iis
s nno
ot
t tto
oo
o hhi
ig
gh
h ffo
or
r
t th
he
e eex
xi
is
st
ti
in
ng
g ttr
ra
af
ff
fi
ic
c cco
on
nd
di
it
ti
io
on
ns
s!
!
K
W WA
AR
RN
NI
IN
NG
G
BA
B8L-068Fig. 148
Page 200 of 272
196Checking and refilling
• Check acid level of the battery⇒"Battery chapter". Depending
on the technique used while charging battery acid could
vaporize.
K
If the battery is disconnected and then reconnected...
P Pl
le
ea
as
se
e nno
ot
te
e tth
he
e wwa
ar
rn
ni
in
ng
gs
s ffr
ro
om
m tth
he
e ""E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r
a an
nd
d ffo
ol
ll
lo
ow
wi
in
ng
g oon
ne
es
s,
, bbe
ef
fo
or
re
e uun
nd
de
er
rg
go
oi
in
ng
g aan
ny
y wwo
or
rk
k oon
n tth
he
e een
ng
gi
in
ne
e oor
r
e en
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t.
.
After d di
is
sc
co
on
nn
ne
ec
ct
ti
in
ng
g
or charging the battery you should:
To reset the clock
⇒"Instruments" chapter.
Switch on again the automatic opening and closing of the power
windows
⇒"Electrical powered windows" chapter.
Should you have problems with the starting or idling of a petrol
engine start engine as follows: switch on ignition for approximately
30 seconds and switch off again. Start engine.
K
Change battery
Our batteries have been developed to suit their location and have
built-in safety elements. Original SEAT batteries comply with all
maintenance, performance and safety requirements for your
vehicle.
We recommend using a battery that does not require maintenance.
P Pl
le
ea
as
se
e nno
ot
te
e tth
he
e wwa
ar
rn
ni
in
ng
gs
s ffr
ro
om
m tth
he
e ""E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r
a an
nd
d ffo
ol
ll
lo
ow
wi
in
ng
g oon
ne
es
s,
, bbe
ef
fo
or
re
e uun
nd
de
er
rg
go
oi
in
ng
g aan
ny
y wwo
or
rk
k oon
n tth
he
e een
ng
gi
in
ne
e oor
r
e en
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t.
.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
Because of the problem of disposing of the old battery, the renewalshould
preferably done at a Technical Service Centre. Batteries contain, amongst
other things, sulphuric acid and lead and must on no account be putwith
normal household waste.
K