air condition Seat Alhambra 2010 User Guide

Seats and storage compartments175
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Sockets
Introduction
Electrical equipment can be connected to the sockets in the vehicle.
Connected equipment must be in perfect condition and show no signs of
faults.
Additional information and warnings:
xCigarette lighter Ÿpage 173
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Improper use of the sockets or electrical devices could lead to a fire and
cause serious injuries.
xNever leave children unsupervised in the vehicle. The sockets and
equipment connected to them can be used when the ignition is switched
on.
xShould a connected electrical device overheat, switch it off and unplug
it immediately.
Caution
xTo avoid damage to the vehicle's electrical system, never connect equip-
ment that generates electrical current, such as solar panels or battery
chargers, to the 12 Volt sockets in order to charge the vehicle's battery.
xOnly use accessories with approved electromagnetic compatibility
according to current regulations.
xTo avoid damage due to voltage variations, switch off all appliances
connected to the 12 V sockets before switching the ignition on or off and
before starting the engine.
xNever connect an appliance to the 12 Volt socket that consumes more
than the power indicated in watts. Exceeding the maximum power absorption
could damage the vehicle's electrical system.
For the sake of the environment
Do not leave the engine running when the vehicle is at a standstill.
Note
Using electrical appliances with the engine stopped and the ignition
switched on will drain the battery.
Note
Unshielded equipment can cause interference on the radio equipment and
the vehicle's electrical system.
Note
Interference can occur on the radio's AM waveband if electrical appliances
are used near the rear window aerial.

Heating, Ventilation and Air conditioning179
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Heating, Ventilation and Air conditioning
Climate Control
Introduction
Viewing Climatronic information
The factory-fitted radio or navigation system screen briefly displays informa-
tion relating to Climatronic.
The units of temperature measurement is displayed on the factory-installed
radio or navigation system and, depending on the vehicle equipment, can be
set using the Configuration menu on the instrument panel.
Additional information and warnings:
xSEAT information system Ÿpage 70
xWindscreen wash system Ÿpage 124
xAuxiliary heating Ÿpage 187
xCaring for and cleaning the vehicle exterior Ÿpage 269
WARNING
Reduced visibility through the windows increases the risk of serious acci-
dents.
xEnsure that all windows are free of ice and snow and that they are not
fogged up preventing a clear view of everything outside.
xThe maximum heat output required to defrost windows quickly is only
available when the engine has reached its normal running temperature.
Only drive when you have good visibility.
xAlways ensure that you use the climate control and heated rear window
to maintain good visibility.
xNever leave the air recirculation on for a long period of time. If the
cooling mode is switched off and air recirculation mode switched on, the
windows can mist over very quickly, considerably limiting visibility.
xSwitch air recirculation mode off when it is not required.
WARNING
Stuffy or used air will increase fatigue and reduce driver concentration
possibly resulting in a serious accident.
xNever leave the fresh air fan turned off or use the air recirculation for
long periods of time; the air inside the passenger compartment will not be
refreshed.
Caution
xSwitch the climate control system off if you think it may be broken. This
will avoid additional damage. Have the climate control system checked by a
qualified workshop.
xRepairs to the climate control system require specialist knowledge and
special tools. SEAT recommends visiting a qualified workshop.
xDo not smoke when air recirculation is switched on in vehicles with a
climate control system. The smoke taken in could lie on the cooling system
vaporiser and on the activated charcoal cartridge of the dust and pollen filter,
leading to a permanently unpleasant smell.
Note
When the cooling system is turned off, air coming from the outside will not be
dried. To avoid fogging up the windows, SEAT recommends leaving the cooler
WARNING (continued)

Heating, Ventilation and Air conditioning 180
(compressor) on. To do this, press the button. The button indicator
should light up.
Note
If the humidity and temperature outside the vehicle are high, condensation
can drip off the evaporator in the cooling system and form a pool underneath
the vehicle, this is completely normal and there is no need to suspect a leak.
Note
Keep the air vents in front of the windscreen free of snow, ice and leaves to
ensure heating and cooling are not impaired and to prevent the windows
from misting over.
AC

Heating, Ventilation and Air conditioning181
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Controls
To switch a function on or off, press the appropriate button. The corre-
sponding button will light up when a function is switched on. Press the
button again to switch off the function.The LED on each control lights up to indicate that the respective function of a
control has been switched on.
Fig. 129 Detailed view of the centre console: Climatic
controls
Fig. 130 Detailed view of the centre console: Climatronic
controls.

Heating, Ventilation and Air conditioning 182
Some Climatronic controls may also be on the climate control system control
panel located in the rear centre console. These controls are used to make the
appropriate settings for the rear seats.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
Tem-
perature
ˆ ... ˆ
Climatic: rotate the control to adjust the temperature accord-
ingly.
Climatronic: the settings for the left hand side, the right-hand
side and the rear seats are made separately. Rotate the control
to adjust the temperature accordingly. The temperature is indi-
cated on the outside ring.
Fan
 ... –
Climatic: setting 0, fan and Climatic switched off;
setting 4, fan set to maximum.
Climatronic: the Fan speed is automatically adjusted depend-
ing on the vehicle speed to avoid annoying noises. The fan can
also be adjusted manually.
Air dis-
tributionClimatic: rotate the continuous control to direct the airflow to
the desired area.
Climatronic: manually adjustable using the controls.
<
Climatic: defrost function. The airflow is directed at the wind-
screen. In this position, air recirculation is automatically
switched off or is not switched on.
<
Climatronic: defrost function. The air drawn in from outside the
vehicle is directed at the windscreen and air recirculation is
automatically switched off. To defrost the windscreen more
quickly, the air is dehumidified at temperatures over approxi-
mately +1.5 °C (+35 °F) and the fan runs at maximum output.
KThe air is directed at the chest of driver and passengers by the
dashboard air vents.
L– Air distribution towards the footwell.
A1
A2
A3
qAir distribution towards the windscreen and the footwell.
ACClimatic, Climatronic: Press the button to turn off/on cooling.
=
Heated rear window: this only works when the engine is run-
ning and switches off automatically after a maximum of 10
minutes.
Air recirculation mode Ÿpage 185.
oClimatronic: Automatic air recirculation Ÿpage 185.
pWindscreen heating: only works when the engine is running
and switches off automatically after a few minutes.
>Instant auxiliary heating on/off button Ÿpage 187.
Switching
off
OFFClimatic: turn the fan switch to setting 0.
Climatronic: press the button or set the fan manually to 0.
When the system switches off, the button will light up.
REAR
Climatronic: press the button to adjust the climate con-
trol for the rear seats from the front. The button will light
up when the function is switched on. The settings for the rear
seats will be displayed. Press the button again to switch the
function off or do not touch any other button for around 10
seconds.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
OFF
OFF
REAR
REST

Heating, Ventilation and Air conditioning183
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Never turn off the air fan for a long time or the air in the passenger compart-
ment will not be refreshed.
xStuffy or used air will increase fatigue and reduce driver and passenger
concentration possibly resulting in a serious accident.
Note
Not all Climatronic buttons are operational in REAR mode.
Note
The button is locked in defrost mode.
Climate control user instructions
The cooling system only works when the engine is running and fan is
switched on.
The climate control system operates most effectively with the windows and
the sliding panoramic roof closed. However, if the vehicle has heated up after
standing in the sun for some time, the air inside can be cooled more quickly
by opening the windows briefly.
Keep the air vents in front of the windscreen free of snow, ice and leaves to
ensure heating and cooling are not impaired and to prevent the windows
from misting over.
Adjustment for safer driving
When the air conditioning is switched on, the temperature and the air
humidity in the vehicle interior drop. Hence, when the outside air humidity is
high, the windows do not mist over and comfort for the vehicle occupants is
improved:
With Climatic
xDisable air recirculation mode Ÿpage 185.
xSet the fan to setting 1 or 2.
xTurn the temperature control to the centre position.
xOpen the air outlets in the dash panel Ÿpage 185.
xTurn the air distribution control to the required position.
xPress the button to turn on cooling. The button will light up.
With Climatronic
xPress the button.
xSet the temperature to +22 °C (+72 °F).
xOpen the air outlets in the dash panel Ÿpage 185.
REST
Climatronic: press the button to use residual heat. When
the engine is still warm but the ignition switched off, the heat
given off by the engine can be used to keep the passenger
compartment warm. The button will light up when the
function is switched on. The function will switch off after
around 30 minutes and if the battery level is low.
p
Climatronic: transferring the driver's seat temperature settings
to the other seats. If the button is not lit up, the set tem-
perature in the driver's seat will also apply to the other seats.
Press the button or the temperature control for the front pas-
senger's seat or the rear seats to set them to a different tem-
perature. The button lights with an indicator.
Vehicles with auxiliary heating: observe the description of the
button.
AUTOAutomatic temperature, fan, and air distribution control.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
REST
REST
p
AUTO
REAR
AC
AUTO

Heating, Ventilation and Air conditioning 184
Switching the Climatronic temperature measuring unit
Press and hold the and buttons to switch the temperature display
between Celsius and Fahrenheit.
Heat
The maximum heat output required to defrost windows quickly is only avail-
able when the engine has reached its normal running temperature.
The air conditioning system does not switch on
If the air conditioning system cannot be switched on, this may be caused by
the following:
xThe engine is not running.
xThe fan is switched off.
xThe climate control fuse has blown.
xThe outside temperature is lower than approximately +3 °C (+38 °F).
xThe climate control system compressor has been temporarily switched off
because the engine coolant temperature is too high.
xAnother fault in the vehicle. Have the climate control system checked by
a qualified workshop.
Things to note
If the humidity and temperature outside the vehicle are high, condensation
can drip off the evaporator in the cooling system and form a pool underneath
the vehicle. This is normal and does not indicate a leak!
Dust and pollen filter
The dust and pollen filter with its activated charcoal cartridge serves as a
barrier against impurities in the ambient air.
For the climate control system to work with maximum efficiency, the dust and
pollen filter must be replaced at the intervals specified in the Maintenance
Programme.If the filter loses efficiency prematurely due to use in areas with very high
levels of air pollution, the filter must be changed more frequently than stated
in the Service Schedule.
Note
The climate control system must left running for a few minutes to reach the
set temperature in the vehicle interior.
Note
After starting it, any residual humidity in the climate control system could
mist over the windscreen.
Note
The air from the vents flows through the passenger compartment and out
through the outlets below the rear window. Do not cover these outlets with
items of clothing or other objects.
ACAUTO

Heating, Ventilation and Air conditioning185
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Air vents
Air vents
Never close the air vents Ÿfig. 131 completely to ensure heating,
cooling and ventilation inside the vehicle.
xTurn the thumbwheel in the required direction to open and close the air
vents.
xChange the air direction using the ventilation grille lever.
There are additional vents in the footwell areas and in the rear of the
passenger compartment.
Caution
Never place food, medicines or other heat-sensitive objects close to the air
vents. Food, medicines and other heat-sensitive objects may be damaged or
made unsuitable for use by the air coming from the air vents.
Air recirculation mode
Important
Air recirculation works in two ways:
Air recirculation mode
 prevents the ambient air from entering the vehicle
interior.
When the outside temperature is very high or very low, selecting manual air
recirculation mode for a short period refreshes or heats the vehicle interior
more quickly.
For safety reasons, air recirculation mode is switched off when the button
is pressed or the air distributor turned to
< Ÿ.
Fig. 131 Air vents in the instrument panel.
AA
Manual air recirculation mode.
oAutomatic air recirculation mode.
<

Heating, Ventilation and Air conditioning 186
Switching air recirculation mode on and off manually 
Switching on: press the corresponding button until the light under the symbol  comes on.
Switching off: press the button until no indicator remains lit.
Automatic air recirculation mode
o
Fresh air enters the vehicle interior in position o. If the system detects a high
concentration of hazardous substances in the ambient air, air recirculation
mode is switched on automatically. When the level of impurities drops to
within a normal range, recirculation mode is switched off.
The system is unable to detect unpleasant smells.
Air recirculation mode is not automatically switched on in the following cases
of outside temperatures and conditions:
xThe cooling system is switched on (the button is lit up) and the
outside temperature is below +3 °C (+38 °F).
xThe cooling system and the windscreen wipers are switched off and the
outside temperature is below +10 °C (+50 °F).
xThe cooling system is switched on, the outside temperature is below +15
°C (+59 °F) and the windscreen wipers are switched on.
Switching the automatic air recirculation mode on and off
Switching on: press the button until the light under the symbol
o
comes on.
Switching off: press the button until no button remains lit.
Switching the automatic air recirculation mode off temporarily
xPress the button once to temporarily switch to manual air recircula-
tion mode in the event of unpleasant smells from outside. The control light
under the symbol
 comes on.
xAfter more than two seconds, press the button again to restart
automatic air recirculation. The control light under the symbol o comes on.
WARNING
Stuffy or used air will increase fatigue and reduce driver concentration
possibly resulting in a serious accident.
xNever use recirculation mode for long periods as it does not refresh the
air inside the vehicle.
xIf the cooling mode is switched off and air recirculation mode switched
on, the windows can mist over very quickly, considerably limiting visibility.
xSwitch air recirculation mode off when it is not required.
Caution
Do not smoke when air recirculation is switched on in vehicles with a climate
control system. The smoke taken in could lie on the cooling system vaporiser
and on the activated charcoal cartridge of the dust and pollen filter, leading
to a permanently unpleasant smell.
Note
Air recirculation mode switches on to prevent exhaust gas from entering the
vehicle interior when it is in reverse and while the automatic windscreen
wash and wipe is working.
AC
 o
 o
 o
 o

Heating, Ventilation and Air conditioning187
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Auxiliary heater* (additional heater)
Introduction
The auxiliary heater is powered by fuel from the vehicle's fuel tank and can be
used while the vehicle is in motion and at a standstill. Select the mode
required (heat or fan) Ÿpage 189 on the instrument panel.
In winter, the auxiliary heater can be used in heat mode before switching on
the ignition to remove any ice, mist or snow from the windscreen (thin layers
only).
Additional information and warnings:
xSEAT information system Ÿpage 70
xRefuelling Ÿpage 293
WARNING
The auxiliary heater fumes contain carbon dioxide, an odourless and
colourless toxic gas. Carbon monoxide can cause people to lose conscious-
ness. It can also cause death.
xNever switch on the auxiliary heater or leave it running in places that
are enclosed or unventilated.
xNever program the independent heating system to be activated and
operated in closed, unventilated areas.
WARNING
The components of the auxiliary heater exhaust system heat up a great
deal. This could cause a fire.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as dried grass).
Caution
Never place food, medicines or other heat-sensitive objects close to the air
vents. Food, medicines and other heat-sensitive objects may be damaged or
made unsuitable for use by the air coming from the air vents.
Switching the auxiliary heater on and off
Switching the auxiliary heater on:
Manually using the instant on/off button.Ÿpage 1
81
Manually using the remote control.Ÿpage 1
88
Automatically at the programmed and enabled on
time.Ÿpage 1
89
Switching the auxiliary heater off:
Manually using the instant on/off button for the cli-
mate control system.Ÿpage 1
81
Manually using the remote control.Ÿpage 1
88
Automatically after the programmed time.Ÿpage 1
89
Automatically when the light comes on z (fuel
reserve).Ÿpage 2
93
Automatically when the battery power drops to a very
low level.Ÿpage 3
18
>
ON
>
OFF