seats Seat Alhambra 2010 Owner's Guide

Child safety 46
Different mounting systems
Always secure child seats properly and safely in the vehicle according to the
child seat manufacturer's installation instructions.
Mounted child seats must rest correctly on the vehicle's seat and must not
move or rock more than 2.5 cm (1 inch).
Child seats equipped for a Top Tether strap must also be secured using the
Top Tether retaining strap in the vehicle Ÿpage 50. Only secure the retaining
belt to the rings fitted for this purpose and identified as Top Tether. Not all
rings can be used with the Top Tether system. Always tighten the Top Tether
retaining strap so that the child seat fits snugly against the corresponding
seat in the vehicle.
Specific mounting systems for each country
Europe: ISOFIX retaining rings and upper retaining strap Ÿpage 49 and
Ÿpage 50.
Retaining rings and upper retaining strap:
USA: LATCH (Lower Anchors and Tethers for CHildren)Canada: lower universal anchorages
Ÿpage 49.
Three-point seat belt and upper retaining strap Ÿpage 48.
The systems include the child restraint system mounting with an upper
retaining strap (Top Tether) and lower anchoring points on the seat.
Use of the child seat on the front passenger seat
Transporting children on the front passenger seat is not permitted in all coun-
tries. Furthermore, not all child seats are approved for use on the front
passenger seat. Your SEAT qualified workshop has an updated list of all
approved child seats. Only used child seats that are approved for each
vehicle.
Fig. 26 On the rear seats: Figures and show the
basic child restraint system mounting using lower
retaining rings and the upper retaining strap. Figure
shows the child restraint system mounting using the
vehicle's seat belt.AAAB
AC
AA
AB
AC

Child safety47
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The frontal airbag on the front passenger side is highly dangerous for a child.
The front passenger seat is life-threatening to a child if he or she is trans-
ported in a rear-facing child seat.
If a rear-facing child seat is secured to the front passenger seat, an inflating
airbag can strike it with such great force that severe or fatal injuries may result
Ÿ. Therefore, rear-facing child seats must never be used on the front
passenger seat when the front passenger airbag is enabled.
Only use a rear-facing child seat on the front passenger seat if the front
passenger airbag is disabled. When it is disabled, the yellow PASSENGER AIR
BAG
/&&  control lamp on the instrument panel will be lit Ÿpage 33. If you
cannot disable the front passenger airbag and it remains enabled, it is
forbidden to transport children on the front passenger seat Ÿ.
Things to note if using a child seat on the front passenger seat:
xThe front passenger airbag must be disabled ’ Ÿpage 36 if using a
rear-facing child seat.
xThe backrest of the front passenger seat must be upright.
xThe front passenger seat must be moved as far back as possible.
xThe backrest of the front passenger seat must be upright.
xThe seat belt height adjustment must be as high as possible.
Suitable child seats
The child seat must be authorised by the manufacturer especially for use on
a front passenger seat with a frontal or side airbag.
If the front passenger seat is equipped with retaining rings, the child seat can
be secured using the approved retaining system provided it is approved for
this type of vehicle in accordance with current regulations in the country in
question.
Universal seats for children in groups 0, 0+, 1, 2 or 3 according to the ECE-R
44 regulation.
WARNING
If a child seat is mounted on the front passenger seat, the risk of the child
sustaining severe or fatal injuries in the event of an accident increases.
Rear-facing child seats must never be mounted on the front passenger seat
when the front passenger airbag is enabled. This is life-threatening to the
child should the frontal airbag deploy, as the child seat would be struck by
the inflated airbag and thrown against the backrest.
WARNING
If, in exceptional circumstances, a child must be transported in a rear-
facing child seat on the front passenger seat, strictly observe the
following:
xAlways disable the front passenger airbag and leave it disabled.
xThe child seat must be approved by the manufacturer for use on a front
passenger seat with frontal and side airbag.
xFollow the installation instructions of the child seat manufacturer and
observe the warnings.
xMove the front passenger seat as far back as possible and adjust it to
its highest position to keep as far away as possible from the frontal airbag.
xMove the backrest to the upright position.
xThe seat belt height adjustment must be as high as possible.
xChildren must always be protected with an approved child restraint
system suited to their height and weight.
Use of the child seat on the rear seat
If a child seat is mounted on the rear seat, adapt the position of the front
passenger seat so that the child has enough space. Therefore, adapt the front

Child safety 48
passenger seat to the size of the child seat and the height of the child. Ensure
the passenger is in the correct position ’ Ÿpage 10.
Move the second and third row of seats fully back and lock them. Place the
seat backs in a vertical position and fold the armrests down.
ISOFIX child seats approved for rear seats
The rear seats are suitable for child seats with the ISOFIX system specially
designed for this type of vehicle in accordance with regulation ECE-R 44.
ISOFIX child seats are divided into “specific categories for the vehicle”,
“limited” or “semi-universal”.
Child seat manufacturers supply a list of vehicles with each ISOFIX seat,
which includes the models for which the ISOFIX child seat in question is
approved. If the vehicle is included in the manufacturer's list and the ISOFIX
child seat belongs to a seat category included in the list, then it can be used
in your vehicle. If necessary, contact the child seat manufacturer for an
updated list of vehicles.
WARNING
If child seats are fitted to all the seats in the second row then it is possible
that the seats of this row cannot be folded down from the third row of seats
in case of an accident. In case of an emergency, passengers in the third row
of seats will not be able to leave the vehicle or to help themselves.
xChild seats should not occupy all the seats of the second row if other
passengers are to occupy the third row of seats.
Securing child seats with the seat belt
Securing the child seat using the seat belt
xPlease read and observe the child seat manufacturer's handling instruc-
tions.
xPositioning the child seat on the seat according to the manufacturer's
instructions.
xThe seat belt height adjustment must be as high as possible.
Group (weight
category)ISOFIX child seat
categorySeat position on the
rear seats
Group 0: chil-
dren up to 10 kgEIUFa)
Group 0+: chil-
dren up to 13 kg
EIUFa)
DIUFa)
CIUFa)
Group 1: 9 to 18
kg
DIUFa)
CIUFa)
BIUFa)
B1IUFa)
AIUFa)
a)IUF: suitable for “universal” ISOFIX child seats authorised for use in this group.
Group (weight
category)ISOFIX child seat
categorySeat position on the
rear seats

Child safety 50
There are two retaining rings, the so-called lower anchor points, on each rear
seat or, where applicable, on the front passenger seat. The retaining rings are
attached to the seat frames.
Child seats with rigid mounting
xObserve the manufacturer's instructions when installing and removing
the child seat Ÿ.
xPress the child seat onto the retaining rings Ÿpage 49, fig. 27 or
Ÿpage 49, fig. 28 in the direction of the arrow. The child seat must be safely
engaged and click audibly into place.
xPull on both sides of the child seat to ensure that it is secure.
Child seat with adjustable retaining straps
xObserve the manufacturer's instructions when installing and removing
the child seat Ÿ.
xPlace the child seat on the seat cushion and attach the retaining strap
hooks to the retaining rings Ÿpage 49, fig. 27 or Ÿpage 49, fig. 28.
xTighten the straps evenly using the corresponding adjustment device.
The child seat must sit flush against the vehicle seat.
xPull on both sides of the child seat to ensure that it is secure.
WARNING
The lower anchor points for child seats do not include rings. Only secure
booster seats to lower anchor points.
Securing a child seat using a Top Tether retaining strap
xObserve the manufacturer's instructions when installing and removing
the child seat Ÿ.
xRaise the head restraint behind the child seat until it engages.
xSecure the child seat to the lower anchor points Ÿpage 49.
xPull the upper child seat retaining strap back to the backrest of the rear
seat, below or on both sides of the head restraint (depending on the child
seat model).
xHook the upper retaining strap to the corresponding retaining ring (for
TOP TETHER) on the back of the backrest on the rear seat Ÿfig. 29.
xPush the head restraint down as far as it will go. Ensure that it does not
interfere with the seatbelt from the upper attachment.
xTighten the strap so that the top of the child seat rests on the backrest.
Fig. 29 Upper retaining
strap hooked in the
luggage compartment

Child safety51
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Child seats with lower anchor points and with an upper retaining strap
must be installed in line with the manufacturer's instructions. Failure to
comply could result in severe injuries.
xAlways secure just one retaining strap from a child seat to a retaining
ring (for TOP TETHER) on backrest on the rear seat in the luggage compart-
ment.
xNever secure a child seat to the retaining rings.
xNever secure a child seat to the movable attachment elements for vehi-
cles with an attachment element and rail system.

Child safety53
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Unfolding the integrated child seat
The integrated child seat can be fitted with a side head restraint. SEAT recom-
mends use of the integrated child seat with the side head restraint fitted and
also that this seat be used only for children above the age of 3.Lifting the cushion
xPull the unlock lever Ÿfig. 30 on the cushion in the direction of the
arrow Ÿfig. 30 .
Fig. 30 Integrated child
seats. lift up the cushion.
Fig. 31 Integrated child seats. position the head
restraint over the side head restraint and fit into place
.AAAB
AAA1

Child safety 54
xFold both sides Ÿpage 53, fig. 30 up in the direction of the arrow
Ÿpage 53, fig. 30 .
xPush the cushion Ÿpage 53, fig. 30 back in the direction of the arrow
Ÿpage 53, fig. 30 until it engages.
Fitting the side head restraint
xFold the backrest of the rear seat forwards Ÿpage 137.
xRemove the head restraint.
xMake sure the belt guide handle on the window side is on the side head
restraint Ÿpage 54.
xInsert the guide rods Ÿpage 53, fig. 31 of the head restraint into the
guides on the side head restraint Ÿpage 53, fig. 31 .
xInsert the head restraint and the side head restraint into the guides on the
corresponding backrest Ÿpage 53, fig. 31 .
xPush the head restraint down as far as it will go.
xFold the backrest of the rear seat back.
xPull the rear seat and the backrest to check whether they are engaged
properly.
Seat belt routing on the integrated child seat
Using the guide handle Ÿfig. 33, position the seat belt so that the shoulder
part of the belt lies on the centre of the child's shoulder.
ABA2
ACA3
A1A2
ABFig. 32 Integrated child
seats. Adjusting the belt
webbing.
Fig. 33 Integrated child
seats. seat belt routing
with guide handle.

Child safety55
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Seat belt guide handle
xSecure the seat belt guide handle to the side head restraint on the
window side. The guide handle is secured by a button.
xOpen the upper button on the seat belt guide handle and pass the belt
webbing below the side head restraint and through the guide handle.
xClose the button again.
Adjusting the belt routing
xGuide the automatic three-point seat belt below the side head restraint.
xPull the latch plate and slowly place the belt webbing across the child's
chest and lap.
xInsert the latch plate into the buckle for the appropriate seat and push it
down until it is securely locked with an audible click.
xPull the belt to ensure that the latch plate is securely engaged in the
buckle.
WARNING
The seat belt only offers maximum protection from severe or fatal injuries
when it is correctly positioned.
xChildren must assume the proper sitting position and be properly
belted in while travelling.
xThe shoulder belt must be positioned against the middle of the
shoulder.
xThe seat belt must lie flat and fit comfortably.
xAllow the belt to retract until it fits tightly over the child's seat.
xThe lap part of the seat belt must lie across the pelvis, never across the
stomach.
xOnly one child may occupy a child seat.
Removing the seat belt
Lowering the cushion
xPull the unlock lever Ÿfig. 34 on the cushion in the direction of the
arrow .
xPush the cushion down through the central area in the direction of the
arrow until it safely engages Ÿ. The side supports fold away automat-
ically.
Removing the side head restraint
xOpen the seat belt guide handle.
xGuide the seat belt by hand to pull the belt back in more easily and not
damage the trim.
xPush the head restraint up as far as it will go.
xFold the backrest of the rear seat forwards Ÿpage 137.
xRemove the head restraint along with the side head restraint.
xRemove the head restraint and side head restraint by pulling on it.
xFitting the head restraint.
Fig. 34 Integrated child
seats. lowering the
cushion.
AAA1
ABA2

Unlocking and locking 102
Electric windows
Introduction
Additional information and warnings:
xSEAT information system Ÿpage 70
xCentral locking and locking system Ÿpage 83
WARNING
Careless use of the electric windows can cause serious injury.
xOnly operate the electric windows when nobody is in the way.
xNever leave children or disabled people alone in the vehicle if the doors
are to be locked. The windows cannot be opened in case of an emergency.
xAlways take all the keys with you whenever you leave the vehicle. After
turning off the ignition, the windows can be opened and closed for a short
time using the buttons on the door as long as the driver's door or
passenger side door is not open.
xWhen transporting children in the rear seats, always deactivate the rear
electric windows with the child safety lock so that they cannot be opened
and closed.

Unlocking and locking 104
To stop the one touch function: Push or pull on the button of the corre-
sponding window.
Restoring one-touch opening and closing
The one-touch opening and closing function is not active after the vehicle
battery has been disconnected or is flat and will have to be reset.
xClose all windows and doors.
xPull the button of the corresponding window and hold it for one second in
this position.
xRelease the button and pull upwards and hold again. The one-touch func-
tion is now ready for operation.
The automatic one-touch electric windows can be reinitialised individually or
several at a time.
Convenience opening and closing function
The electric windows can be opened or closed from outside using the vehicle
key:
xHold in the unlocking for locking button for the vehicle. All windows which
function electrically will be either opened or closed.
xTo interrupt the function, release the locking or unlocking button.
During convenience closing, first the windows and then the sliding sunroof
will be closed.
In the Configuration - convenience menu, there are different settings for oper-
ating the windows Ÿpage 70.
WARNING
Careless use of the electric windows can cause serious injury.
xOnly operate the electric windows when nobody is in the way.
xNever leave children or disabled people alone in the vehicle if the doors
are to be locked. The windows cannot be opened in case of an emergency.
xAlways take all the keys with you whenever you leave the vehicle. After
turning off the ignition, the windows can be opened and closed for a short
time using the buttons on the door as long as the driver's door or
passenger side door is not open.
xWhen transporting children in the rear seats, always deactivate the rear
electric windows with the child safety lock so that they cannot be opened
and closed.
Note
The one-touch function and roll-back function will not work if there is a
malfunction in the electric windows. Visit a specialist workshop.
Electric Windows anti-trap function
The anti-trap function of the electric windows can reduce the risk of injury
when opening and closing the electric windows Ÿ. If a window is not able
to close because it is stiff or because of an obstruction, it will automatically
open again.
xCheck why the window does not close.
xAttempt to close the window again.
xIf you try within the following 10 seconds and the window closes with
difficulty or there is an obstruction once again, the one-touch closing will stop
working for 10 seconds.
xIf the window is still obstructed, it will stop at the corresponding position.
When the button is operated within 10 seconds, the window will close
without the anti-trap function Ÿ.
WARNING (continued)