belt Seat Alhambra 2010 Owner's Guide

Child safety 50
There are two retaining rings, the so-called lower anchor points, on each rear
seat or, where applicable, on the front passenger seat. The retaining rings are
attached to the seat frames.
Child seats with rigid mounting
xObserve the manufacturer's instructions when installing and removing
the child seat Ÿ.
xPress the child seat onto the retaining rings Ÿpage 49, fig. 27 or
Ÿpage 49, fig. 28 in the direction of the arrow. The child seat must be safely
engaged and click audibly into place.
xPull on both sides of the child seat to ensure that it is secure.
Child seat with adjustable retaining straps
xObserve the manufacturer's instructions when installing and removing
the child seat Ÿ.
xPlace the child seat on the seat cushion and attach the retaining strap
hooks to the retaining rings Ÿpage 49, fig. 27 or Ÿpage 49, fig. 28.
xTighten the straps evenly using the corresponding adjustment device.
The child seat must sit flush against the vehicle seat.
xPull on both sides of the child seat to ensure that it is secure.
WARNING
The lower anchor points for child seats do not include rings. Only secure
booster seats to lower anchor points.
Securing a child seat using a Top Tether retaining strap
xObserve the manufacturer's instructions when installing and removing
the child seat Ÿ.
xRaise the head restraint behind the child seat until it engages.
xSecure the child seat to the lower anchor points Ÿpage 49.
xPull the upper child seat retaining strap back to the backrest of the rear
seat, below or on both sides of the head restraint (depending on the child
seat model).
xHook the upper retaining strap to the corresponding retaining ring (for
TOP TETHER) on the back of the backrest on the rear seat Ÿfig. 29.
xPush the head restraint down as far as it will go. Ensure that it does not
interfere with the seatbelt from the upper attachment.
xTighten the strap so that the top of the child seat rests on the backrest.
Fig. 29 Upper retaining
strap hooked in the
luggage compartment

Child safety 52
Integrated child seat
Introduction
The integrated child seat is only suitable for children in Group 2 (15-25 kg)
and Group 3 (22-36 kg), according to the ECE-R 44 regulation.
Additional information and warnings:
xSeat belts Ÿpage 22
WARNING
Child travelling without their seat belt fastened or not secured using a suit-
able restraint system may sustain fatal injuries if the airbag is deployed.
xYou should always transport all children up to 12 years of age on the
rear seat.
xAlways disable the front passenger airbag if, in exceptional cases, you
have no alternative but to transport a child in a rear-facing child safety seat
on the front passenger seat.
xChildren must always be protected with a child restraint system suited
to their height and weight.
xAlways fasten children's seat belts correctly.
WARNING
Children must travel in a child seat appropriate to their weight and height
while the vehicle is in motion.
xChildren must always be protected with a child restraint system suited
to their height and weight.
xChildren must assume the proper sitting position and be properly
belted in while travelling.
xThe shoulder part of the seat belt must lie approximately on the centre
of the shoulder, never across the neck or the arm.
xThe seat belt must lie close to the upper part of the body.
xThe lap belt part must lie across the pelvis, not across the stomach, and
always fit closely.
xAllow the belt to retract until it fits tightly over the child's seat.
xNever hold children or babies on your lap.
xAlways use a child seat and the seat belt for children who are less than
1.5 metres tall. The normal seat belt could cause injuries to the abdominal
and neck areas.
xOnly one child may occupy a child seat.
xRead and follow the information and warnings provided by the child
seat manufacturer.
xNever leave an unsupervised child alone on a child seat or in the
vehicle.
xAll modifications to the integrated child seat must be carried out by a
specialist workshop.
xReplace the child seat or any seat components damaged or involved in
an accident.
WARNING
Loose objects could fly uncontrollably around the vehicle interior and
cause injuries in the event of an accident or sudden braking.
xDo not leave toys or other hard, loose objects on the child seat or on the
seat while the vehicle is in motion.
WARNING (continued)

Child safety 54
xFold both sides Ÿpage 53, fig. 30 up in the direction of the arrow
Ÿpage 53, fig. 30 .
xPush the cushion Ÿpage 53, fig. 30 back in the direction of the arrow
Ÿpage 53, fig. 30 until it engages.
Fitting the side head restraint
xFold the backrest of the rear seat forwards Ÿpage 137.
xRemove the head restraint.
xMake sure the belt guide handle on the window side is on the side head
restraint Ÿpage 54.
xInsert the guide rods Ÿpage 53, fig. 31 of the head restraint into the
guides on the side head restraint Ÿpage 53, fig. 31 .
xInsert the head restraint and the side head restraint into the guides on the
corresponding backrest Ÿpage 53, fig. 31 .
xPush the head restraint down as far as it will go.
xFold the backrest of the rear seat back.
xPull the rear seat and the backrest to check whether they are engaged
properly.
Seat belt routing on the integrated child seat
Using the guide handle Ÿfig. 33, position the seat belt so that the shoulder
part of the belt lies on the centre of the child's shoulder.
ABA2
ACA3
A1A2
ABFig. 32 Integrated child
seats. Adjusting the belt
webbing.
Fig. 33 Integrated child
seats. seat belt routing
with guide handle.

Child safety55
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Seat belt guide handle
xSecure the seat belt guide handle to the side head restraint on the
window side. The guide handle is secured by a button.
xOpen the upper button on the seat belt guide handle and pass the belt
webbing below the side head restraint and through the guide handle.
xClose the button again.
Adjusting the belt routing
xGuide the automatic three-point seat belt below the side head restraint.
xPull the latch plate and slowly place the belt webbing across the child's
chest and lap.
xInsert the latch plate into the buckle for the appropriate seat and push it
down until it is securely locked with an audible click.
xPull the belt to ensure that the latch plate is securely engaged in the
buckle.
WARNING
The seat belt only offers maximum protection from severe or fatal injuries
when it is correctly positioned.
xChildren must assume the proper sitting position and be properly
belted in while travelling.
xThe shoulder belt must be positioned against the middle of the
shoulder.
xThe seat belt must lie flat and fit comfortably.
xAllow the belt to retract until it fits tightly over the child's seat.
xThe lap part of the seat belt must lie across the pelvis, never across the
stomach.
xOnly one child may occupy a child seat.
Removing the seat belt
Lowering the cushion
xPull the unlock lever Ÿfig. 34 on the cushion in the direction of the
arrow .
xPush the cushion down through the central area in the direction of the
arrow until it safely engages Ÿ. The side supports fold away automat-
ically.
Removing the side head restraint
xOpen the seat belt guide handle.
xGuide the seat belt by hand to pull the belt back in more easily and not
damage the trim.
xPush the head restraint up as far as it will go.
xFold the backrest of the rear seat forwards Ÿpage 137.
xRemove the head restraint along with the side head restraint.
xRemove the head restraint and side head restraint by pulling on it.
xFitting the head restraint.
Fig. 34 Integrated child
seats. lowering the
cushion.
AAA1
ABA2

Cockpit61
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Instrument panel
Control and warning lamps
The control and warning lamps are indicators of warnings, Ÿ, faults Ÿ
or certain functions. Some control and warning lamps come on when the igni-
tion is switched on, and go out when the engine starts running, or while
driving.
Depending on the model, additional text messages may be viewed on the
instrument panel display. These may be purely informative or they may be
advising of the need for action Ÿpage 64, “Instruments”.
Depending upon the equipment fitted in the vehicle, instead of a warning
lamp, sometimes a symbol may be displayed on the instrument panel.
When certain control and warning lamps are lit, an audible warning is also
heard.
Red symbols
Yellow symbols
SymbolMeaning ŸSee
H
› Do not continue driving!
The electronic parking brake is on, the brake
fluid level is too low or the brake system is
faulty.
Ÿpage 210
v› Do not continue driving!
Fault in the engine cooling system.Ÿpage 313
E› Do not continue driving!
Engine oil pressure too low.Ÿpage 309
o
› Do not continue driving!
At least one of the vehicles doors is open, or is
not correctly closed.Ÿpage 92
˜› Do not continue driving!
The tailgate is open or is incorrectly closed.Ÿpage 97
D› Do not continue driving!
Fault in the steering.Ÿpage 192
bEngine cannot be started again!
"AdBlue" level too low.Ÿpage 300
hDriver or passenger has not fastened seat belt.Ÿpage 22
KUse the foot brake!
Change
Ÿpage 201
Brake
Ÿpage 210
FFaulty generator.Ÿpage 318
IFront brake pads worn.
Ÿpage 210«lights: ESP faulty or off
flashes: ESP functioning.
lTCS manually deactivated.
JABS faulty or does not work.
Electronic parking brake faulty.Ÿpage 210

Rear fog light switched on.Ÿpage 113
SymbolMeaning ŸSee

Cockpit 62
Green symbols
Blue symbols
Colourless symbols
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
lights: Driving light totally or partially faulty.Ÿpage 360
flashes: Fault in the adaptive light system.Ÿpage 113
BFault in catalytic converter.
Ÿpage 255Dlights: pre-ignition of diesel engine.
flashes: Fault in engine management.
%0#Fault in engine management.
¬Diesel particulate filter blocked
DFault in the steering system.Ÿpage 192
~Tyre pressure too low.Ÿpage 323
Fault in the tyre pressure gauge.Ÿpage 245
YLevel of windscreen washer fluid too low.Ÿpage 124
Fuel tank almost empty.Ÿpage 293
Eflashes: Engine oil sensor faulty.Ÿpage 309lights: Insufficient engine oil.
TFault in airbag system and seat belt tensioners.Ÿpage 33
/&&

Passenger front airbag is off (PASSENGER
AIRBAG
/&& ).Ÿpage 33
bTop up "AdBlue", or there is a fault in the "AdB-
lue" system.Ÿpage 300
§Fuel tank not closed correctly.Ÿpage 293
SymbolMeaning ŸSee

Left or right turn signal.Ÿpage 113
Hazard warning lights on.Ÿpage 345
KUse the foot brake!
Change
Ÿpage 201
Brake
Ÿpage 210
%Cruise control operating.Ÿpage 239
SymbolMeaning ŸSee
Headlight on or flasher on.
Ÿpage 113
+Headlight adjustment (Light Assist) on.
SymbolMeaning ŸSee
3!&%Electronic immobiliser active.Ÿpage 195
>Service interval displayŸpage 68

Seats and storage compartments137
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Seat functions
Introduction
Additional information and warnings
xAdjust the seat position Ÿpage 10
xSeat belts Ÿpage 22
xAirbag system Ÿpage 33
xChild seats (accessories) Ÿpage 42
xIntegrated child seats Ÿpage 52
xExterior mirrors Ÿpage 130
xLuggage compartment Ÿpage 146
WARNING
Inappropriate use of the seat functions can cause severe injuries.
xAssume the proper sitting position before your trip and remain in it
throughout. This also applies to the other occupants.
xOnly adjust the seat position memory when the vehicle is stationary.
xOnly switch the lumbar massage function on and off when the vehicle
is stationary.
xKeep hands, fingers, feet and other limbs away from the seat operating
and adjustment radius.
Seat heating
The seat cushions can be heated electrically when the ignition is switch on.
The backrest is also heated in some versions.
Switch off seat heating if there is nobody in the seat.
WARNING
People whose pain and temperature threshold has been affected by some
kind of medicine, paraplegia or chronic illness (e.g. diabetes) may sustain
FunctionAction Ÿfig. 85
To switch system on:Press button A. Seat heating is switched on fully.
Adjusting the heating
output:Keep pressing button A until the required inten-
sity is set.
The system switches
off:Keep pressing button A until all of the lights are
switched off Ÿfig. 85.
Fig. 85 Detailed view of
the centre console: front
seat heating controls,
here with the second
temperature level set.

Seats and storage compartments 140
Convenient entry function for the third row of seats
The outer seats of the second row can be folded to make it easier to get in and
out of the third row of seats.
Folding down the seat of the second row
xIf necessary, open the belt loop and wind up the seat belt by hand.
xIf necessary, remove the side head restraint of the integrated child seat
Ÿpage 52.
xIf necessary, raise the armrests.
xRemove any objects located in the floor area of the second row of seats,
where applicable Ÿ.
xPush the head restraint down as far as it will go Ÿpage 10.
xPush the lever Ÿfig. 87 forwards and fold the backrest of the rear
seat. The seat can still be moved forwards when rear seat is folded completely
forwards Ÿ.
xAlways take care when entering and leaving the vehicle Ÿ.Repositioning the seat of the second row
xLift the backrest of the rear seat in an upright position. The entire seat
folds backwards Ÿ.
xMake sure that the rear seat is securely engaged so that the seat belts can
provide proper protection in the rear seats. The red mark Ÿfig. 87 should
no longer be visible Ÿ in “Folding down rear seats to create load space”
on page 147.
Emergency exit function
If the lever Ÿfig. 87 does not work, e.g. after an accident, the seats on
the second row can be folded forwards from the third row to allow occupants
of the third row of seats to get out of the vehicle Ÿ.
xPull handle Ÿfig. 87 back and fold the backrest of the rear seat. The
complete rear seat folds forward Ÿ.
WARNING
Careless or uncontrolled use of the convenient entry assistant may result
in severe injury and accident.
xNever use the convenient entry function when the vehicle is in motion.
xAvoid trapping or damaging the seat belt when folding the rear seats
back.
xKeep your hands, fingers, feet and other body parts out of the hinges
and the seat locking mechanism when folding and unfolding.
xMats or other objects can be caught in the hinges of the backrests or
rear seat. This could prevent the backrest from locking safely when posi-
tioned upright.
xAll backrests must engage correctly for the seat belts on the rear seats
to work properly. When the backrest of an occupied seat is not correctly
locked in place, the passenger can be thrust forward with the backrest in
case of sudden braking, sudden manoeuvres or an accident.
Fig. 87 Second row of
seats: convenient entry
function controls.
A1
A2
A1
A3

Seats and storage compartments 148
Each rear seat can fold down individually to extend the luggage compart-
ment.
Folding the seats in the second row of seats for loading
xIf necessary, open the belt loop and wind up the seat belt by hand.
xIf it is necessary, remove the head rests on the integrated child seats then
reinstalled the integrated child seats Ÿpage 52.
xIf necessary, raise the armrests.
xRemove objects from the footrest area in front of and behind the rear seat
Ÿ.
xMove the rear seat all the way back.
xPush the head restraint down as far as it will go Ÿpage 10.
xIn the middle seat, close the drinks carrier in the rear of the centre
console, if necessary.
xPull lever Ÿpage 147, fig. 95 back and fold the backrest forwards.
The complete rear seat folds forward Ÿ.
xFold the backrest forwards until it locks into the load surface position
Ÿpage 147, fig. 95 .
xIf necessary, pull on the lever Ÿfig. 96 to move the seat to the
required position.
xWhen the seat is folded down, no adults or children should travel in it
Ÿ.
Folding the seats in the third row of seats for loading
xIf necessary, open the belt loop and wind up the seat belt by hand.
xOpen the tailgate.
xPush the head restraint down as far as it will go Ÿpage 10.
xRemove objects from the footrest area in front of and behind the rear seat
Ÿ.
xRemove objects from the space below the rear seat.
xRemove the attachment elements and supports for the net from the rail
system.
xPull lever Ÿfig. 96 back and fold the backrest forwards. The rear seat
folds forward Ÿ and the cushion also moves forward.
xFold the seat tray forward on top of the folded seat.
Fig. 96 Third row of seats: fold down the rear seat to
load then return to position .AAAB
A1
AB
A2
A1

Seats and storage compartments149
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the seat is folded down, no adults or children should travel in it
Ÿ.
Putting the seats in the second row back in place
xPull lever Ÿpage 147, fig. 95 upwards and place the seatback in
vertical position. The entire seat folds backwards.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
Putting the seats in the third row back in place
xOpen the tailgate.
xPull on the handle Ÿpage 148, fig. 96 to put the seat tray back in
position.
xPull on the handle Ÿpage 148, fig. 96 . The entire seat folds back-
wards.
xPress on the seat tray in the backrest until it is held in position by its
magnets.
xOpen the sliding door.
xPut the backrest into position and press firmly until it clicks into place.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
WARNING
Folding and lifting the rear seats carelessly without paying attention could
cause serious injury.
xNever fold or lift the seats while driving.
xDo no trap or damage seat belts when raising the backrest.
xKeep your hands, fingers, feet and other body parts out of the hinges
and the seat locking mechanism when folding and unfolding.
xMats or other objects can be caught in the hinges of the backrests or
rear seat. This could prevent the seat or backrest from locking securely in
the vertical position.
xAll backrests must engage correctly for the seat belts on the rear seats
to work properly. When the backrest of an occupied seat is not correctly
locked in place, the passenger can be thrust forward with the backrest in
case of sudden braking, sudden manoeuvres or an accident.
xNo seat must be occupied if the backrest or seat is folded or not
correctly engaged.
Caution
Before folding the backrest of the rear seat, adjust the front seats so that the
head restraint or backrest do not hit them when it is folded.
Caution
xObjects placed in the footrest area in front of and behind the rear seats
can be damaged when seats are folded down or put back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xObjects placed in the moulding on the back of the third row of seats can
be damaged when folding down the seats or putting them back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xThe attachment elements and supports for the net partition placed on the
rail system can be damaged when folding down seats from the third row or
putting them back into position and these can also damage the seats them-
selves. Before folding down or repositioning the seats, remove the attach-
ment elements and supports for the net from the rail system.
A1
A2
A3
WARNING (continued)