belt Seat Alhambra 2010 Service Manual

Seats and storage compartments167
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Storage compartments in the rear floor area
Move the mat to one side (where applicable).
To open, pull on the rear centre part of the cover Ÿfig. 116 (arrow).
To close, press the cover down.
WARNING
Make sure children are properly belted in and correctly secured to avoid
severe or fatal injuries while the vehicle is in motion.
xIf you are using a child seat with a base or foot, always install this base
or foot correctly and safely.
xIf the vehicle has a storage compartment in the foot well in front of the
last row of seats, this compartment cannot be used as designed; on the
contrary: It must be filled using the specially designed accessory so that
the base or foot is correctly supported by the closed compartment and the
child seat is secured properly. If this compartment is not suitably secured
when using a child seat with a base or foot then the compartment cover could rupture in an accident and the child will be ejected and suffer serious
injury.
xPlease read and observe the child seat manufacturer's handling
instructions.
Drawers*
There may be a drawer below the front seats.
Opening and closing the drawer
To open, press the button on the drawer handle and pull the drawer out.
To close, push the drawer under the seat until it clicks into place.
Fig. 116 Storage
compartments in the floor
area of the second row of
seats.
WARNING (continued)
Fig. 117 Drawer under
the front seat.

Driving195
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Stopping and starting the engine
Introduction
Immobiliser display
When an invalid key is used or in the event of a system fault,
3!&% or
Immobiliser on is displayed on the instrument panel. The engine cannot be
started.
Pushing or towing
For technical reasons, the vehicle must not be push- or tow-started. Jump
starting is preferable.
Additional information and warnings:
xVehicle key set Ÿpage 78
xChanging gear Ÿpage 201
xBraking, stopping and parking Ÿpage 210
xSteering Ÿpage 192
xStart assist systems Ÿpage 221
xRefuelling Ÿpage 293
xFuel Ÿpage 297
xEmergency locking and unlocking Ÿpage 348
xJump starting Ÿpage 371
xTow-starting and towing away Ÿpage 375
WARNING
Turning off the engine while driving will make stopping the vehicle diffi-
cult; this could even result in the loss of control causing an accident with
serious consequences.
xThe assisted braking and steering systems, the airbag system, safety
belts and certain safety equipment are only active while the engine is
running.
xThe engine should only be switched off when the vehicle is at a stand-
still.
WARNING
While the engine is running or starting it could help reduce the risk of
serious injury.
xNever start or leave the engine running in poorly ventilated or closed
spaces. Exhaust gas contains carbon monoxide, a toxic, colourless and
odourless gas. Carbon monoxide can cause people to lose consciousness.
It can also cause death.
xNever leave the vehicle unattended if the engine is running. The vehicle
could move off suddenly or something unexpected could happen resulting
in damage and serious injury.
xNever use start boosters. Cold start sprays could explode or increase
the engine speed unexpectedly.
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire and considerable damage.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as wood, leaves, spilled
fuel, dried grass, etc).
xDo not apply additional underseal or anti-corrosion coatings to the
exhaust pipes, catalytic converter, heat shields or the diesel particulate
filter.
WARNING (continued)

Driving 200
WARNING
Never switch off the engine while the vehicle is moving. You may lose
control of the vehicle and there is a risk of serious accident.
xThe airbags and belt tensioners do not work when the ignition is
switched off.
xThe brake servo does not work when the engine is not running. To stop,
the brake pedal must be pressed with more force.
xAs the power steering does not work if the engine is not running, you
will need more strength to steer than normally.
xIf the key is removed from the ignition, the steering may lock and it will
not be possible to steer the vehicle.
Caution
If the engine has been driven at high speed for a prolonged period of time, it
may overheat when turned off. To avoid engine damage, allow the engine to
run for approximately two minutes in neutral before switching it off.
Note
In vehicles with automatic gearbox, the key can only be removed when the
selector lever is in position P.
Note
After stopping the engine, the engine compartment fan may continue running
for a few minutes, even when the ignition has been switched off or the key
removed. The radiator fan is automatically switched off.
Electronic immobiliser
The gear lock prevents the engine from being started with an unauthorised
key and the vehicle being moved.
The vehicle key has a built-in chip. It automatically deactivates the immobi-
lizer when the key is inserted into the ignition lock.
The electronic immobiliser will be activated again automatically as soon as
you remove the key from the ignition lock. In vehicles with the KESSY system,
the key should remain outside the vehicle Ÿpage 86.
For this reason, the vehicle can only be used with a genuine SEAT key with the
correct code. Coded keys can be obtained from your Authorised Service
Centre Ÿpage 78.
If an unauthorised key is used, the message SAFE or Immobiliser active is
displayed on the instrument panel. The vehicle cannot be started in this case
Note
The correct operation of the vehicle is only guaranteed when original SEAT
keys are used.
5.
Turn the key in the ignition lock
to position Ÿpage 196, fig. 134
.Briefly press the starter button
Ÿpage 197, fig. 135. If it is not
possible to switch off the engine,
use the emergency disconnec-
tion Ÿpage 197.
6.With a manual gearbox, put the vehicle in first or reverse gear.
7.
Remove the starter button from
the lock to disconnect all electri-
cal components and activate the
electronic lock on the steering
column.
StepVehicles without KESSYVehicles with KESSY
A0

Driving213
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xPress button . At the same time, press the brake pedal hard or gently
press the accelerator pedal with the engine switched on.
xThe control lamps G on the button and H on the instrument panel go
out.
Automatic release of the electronic parking brake on starting the engine
The electronic parking brake is automatically released when the vehicle starts
moving, if the driver's door is closed and the driver is wearing his/her seat
belt. In vehicles with a manual gearbox the clutch pedal should also be
pressed to the floor before starting the engine so that the system recognises
that the parking brake should be released.
Emergency braking function
Only use the emergency braking function if the vehicle cannot be stopped
with the brake pedal Ÿ!
xPull button hard to stop the vehicle. The warning display will be
accompanied by the corresponding warning chime.
xTo stop the braking process, release the button or press the accelerator.
WARNING
The incorrect use of the electronic parking brake may result in serious acci-
dent.
xNever use the electronic parking brake to brake the vehicle except in an
emergency. The braking distance is considerably longer, because braking
is only applied to the rear wheels. Always use the foot brake.
xNever accelerate from the engine compartment with the engine running
and a gear or a gear range engaged. The vehicle could move, even if the
parking brake is applied.
Note
In vehicles with a manual gearbox: When the clutch pedal is released and the
accelerator pressed at the same time, the electronic parking brake is auto-
matically released.
Note
If the vehicle battery is flat, it will not be possible to disconnect the electronic
parking brake. Use the jump-start Ÿpage 371.
Note
When the electronic parking brake is applied or released, noises may be
heard.
Note
If the electronic parking brake has not been used for a long while, the system
sometimes performs automatic and audible checks while the vehicle is at a
standstill.
Parking
When parking your vehicle, all legal requirements should be observed.
To park the vehicle
Complete operations only in the sequence given.
xPark the vehicle on a suitable surface Ÿ.
xPress and hold the brake pedal until the vehicle comes to a standstill.
xConnect the electronic parking brake Ÿpage 212.
xFor an automatic gearbox, move the selector lever to position P.
G
G

Driving 222
Auto Hold function*
The control lamp on the button switches on when the Auto Hold function is
on.
When the Auto Hold function is on, it helps the driver if they must regularly
stop the vehicle or if they must stop with the engine running for prolonged
periods, for example, on hills, before a traffic light or in traffic jams with
continuous stopping and starting.
The Auto Hold function automatically prevents the vehicle from rolling away
accidentally when at a standstill, without the driver having to keep his/her
foot on the brake pedal.
When the system that detects that the vehicle has stopped, the Auto Hold
keeps the vehicle at a standstill. The brake pedal can be released.
If the driver presses the brake pedal briefly or presses the accelerator to start
off, the Auto Hold function releases the brake once more. The vehicle moves
according to the gradient.If any of the conditions necessary for the Auto Hold function change while the
vehicle stopped, the system is turned off as is the indicator on the button
Ÿfig. 146. The electronic parking brake engages where necessary to park
the vehicle safely Ÿ.
Conditions for keeping the vehicle at a standstill with Auto Hold:
xThe driver's door must be closed.
xThe driver's seat belt must be buckled.
xThe engine must be running.
xThe TCS system must be switched on Ÿpage 210.
Switching Auto Hold on and off manually
Press the button Ÿ. The control lamp on the button switches
off when the Auto Hold function is switched off.
Permanent Auto Hold connection
The Auto Hold function must be switched on every time the engine is started.
However, to switch the Auto Hold function on permanently, the mark must be
switched on in the Settings menu, Autohold submenu Ÿpage 70.
Auto Hold works automatically under the following conditions:
Fig. 146 Detailed view of
the centre console: Auto
Hold button.
All points must be fulfilled simultaneously Ÿ:
manual gearboxAutomatic gearbox
1.If the vehicle is stopped using the brake pedal on a flat or slope.
2.The engine must be running smoothly.
3.On a slope, the 1st gear is
engaged uphill or the reverse gear
is engaged for a downhill. The
clutch must be held down.A gear for driving is selected from
R, D or S.
Upon accelerating and pressing in
the clutch simultaneously, the
brake releases gradually.Upon accelerating, the brake
releases gradually.
AUTO HOLD

Driving 224
Important conditions for the engine to automatically switch off
xThe driver seat belt must be buckled.
xThe driver door must be closed.
xThe bonnet must be closed.
xThe factory-fitted towing bracket must not be electrically connected to a
trailer.
xA minimum engine temperature has been reached.
xThe vehicle has moved since the last stop.
xIn vehicles with Climatronic: The temperature inside the vehicle is within
the preset temperature range.
xThe temperature set is neither very high nor very low.
xThe air conditioning defrost function is not switched on.
xIn vehicles with Climatronic: the blower has not been manually set to a
high speed.
xThe power level of the vehicle's battery is sufficient.
xThe vehicle's battery temperature is neither too high nor too low.
xThe vehicle is not on a steep gradient or slope.
xThe front wheels are not overly turned.
xThe heated windscreen is not switched on.
xReverse gear is not engaged.
xThe park assist system is not switched on.
Conditions for automatically restarting the engine
The engine may automatically restart under the following conditions:
xIf the vehicle interior is too hot or too cold.
xIf the vehicle moves.
xIf the vehicle's battery voltage drops.
Conditions requiring the key to restart the engine
The engine must be started using the key under the following conditions:
xIf the driver unbuckles his/her seat belt.
xIf the driver's door is opened.
xIf the bonnet is opened.
xIn vehicles with a manual gearbox: If a gear has been selected.
Switching Start-Stop mode on and off manually
xPress the button on the centre console Ÿpage 223, fig. 147.
xThe button will light up when the Start-Stop function is switched off.
The engine will start immediately if the vehicle is in Stop mode when it is
switched off manually.
WARNING
The brake servo and the power steering do not work when the engine is
switched off.
xNever allow the vehicle to move when the engine is switched off.
Caution
Using the Start-Stop function for a long period at very high outdoor tempera-
tures could damage the vehicle's battery.
Note
In some cases, you may have to restart the vehicle using the key. Observe the
corresponding message on the instrument panel display.
›

Vehicle maintenance and cleaning 278
Caring for and cleaning the vehicle interior
Introduction
The dye from many items of modern clothing (e.g. dark jeans) is not always
solid enough. Seat upholstery (material and leather), especially when light-
coloured, may visibly discolour if the dye comes out of clothing (even when
used correctly). This is not an upholstery defect but indicates that the dye in
the item of clothing is not solid enough.
Additional information and warnings:
xCaring for and cleaning the vehicle exterior Ÿpage 269
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Car care products may be toxic and hazardous. If car care products are not
suitable or are used inappropriately, this could result in accident, serious
injury, burns or intoxication.
xCar care products must always be stored in the original container which
should be kept closed.
xObserve information provided by the manufacturer.
xTo prevent confusion, never store car care products in empty food cans,
bottles or other containers.
xKeep all care products out of reach of children.
xHarmful vapours may be produced when using car care products. There-
fore, care products should only be used in well-ventilated spaces or in the
open air.
xNever use fuel, turpentine, engine oil, acetone or any other volatile
liquid to wash, clean or care for the vehicle. These are toxic and highly
flammable.
WARNING
Inappropriate care and cleaning of vehicle components may effect the
vehicle safety equipment, increasing the risk of severe injury.
xVehicle components should only be cleaned and maintained in accord-
ance with the manufacturer's instructions.
xOnly use approved or recommended care products.
Caution
xCleaning products which contain solvents will damage the material.
xTo avoid damage, stubborn stains should be removed by a specialist
cleaning company.
Note
Suitable car care products are available from your Technical Service.
Treating your upholstery
Check list
For information on how to treat and care for the vehicle upholstery, please
bear the following in mind Ÿ:
xBefore entering the vehicle, fasten all Velcro fastenings which could come
into contact with upholstery and coverings. If the Velcro fastenings on uphol-
stery and material covers are not securely fastened, this could damage them.
xTo prevent damage, do not allow the upholstery or covers to come into
contact with sharp or decorative objects. Decorative objects such as zips,
rivets and rhinestones on clothing and belts.
xDust and grit in the pores and seams should be removed regularly to
prevent them scratching and damaging the surface.

Vehicle maintenance and cleaning 282
Cleaning seat belts
If the seat belt is very dirty, the belt retractor may not work correctly thus
preventing the seat belt from operating correctly.
The seat belts should never be removed from the vehicle for cleaning.
xUse a soft brush to remove the worst dirt Ÿ.
xPull the seat belt right out and leave it out.
xClean dirty seat belts with a gentle soap and water solution.
xWait until they are completely dry.
xOnly allow the seat belt to retract when it is completely dry.
WARNING
Check the condition of all the seat belts at regular intervals. If the webbing
or other parts of the belt are damaged, the vehicle should be taken to a
qualified workshop immediately and the belts should be replaced. It is
extremely dangerous to drive using damaged seat belts and could result in
serious injury or loss of life.
xSeat belts and their components must never be cleaned with chemical
products, nor should they be allowed to come into contact with corrosive
liquids, solvents or sharp objects. This could affect the strength of the seat
belt webbing.
xSeat belts should be completely dry before retracting. Damp could
damage the belt retractor so that it is does not operate correctly.
xDo not allow liquids or foreign bodies to enter the buckle fastenings.
This could damage the buckles and seat belts.
xNever attempt to repair, modify or remove a seat belt yourself.
xAlways have damaged seatbelts replaced immediately by seat belts
approved for the vehicle in question by SEAT. Seat belts which have been
worn in an accident and stretched must be replaced by a qualified work-shop. Renewal may be necessary even if there is no apparent damage. The
belt anchorage should also be checked.
WARNING (continued)

Vehicle maintenance and cleaning 284
Caution
Aerials on the inside of windows may be damaged if knocked or if cleaned
with corrosive or acid cleaning products. Do not stick adhesive labels over the
heating elements and never clean the inside of the rear window with corro-
sive or acid products or other similar chemical cleaning products.
Note
If electrical equipment is used near an aerial built-into the window, you may
observe interference in the reception of AM stations.
Notes on SEAT repairs
WARNING
Repairs or modifications which are not performed correctly may result in
damage or errors in the vehicle operation, affecting the efficiency of the
driver assist and airbag systems. This could result in serious accident.
xHave any repairs or modifications carried out at a qualified workshop.
Collection and scrapping of end-of-life vehicles
Collection of end-of-life vehicles
An extensive network of used car reception centres already exists in much of
Europe. After the vehicle has been delivered, you will receive a certificate of
destruction describing the environmentally friendly scrapping of the vehicle
in accordance with applicable legislation.
We will collect the used vehicle free of charge, provided it complies with all
national legislation.Please see your Technical Service for further information about the collection
and scrapping of end-of-life vehicles.
Scrapping
The relevant safety requirements must be observed when the vehicle or
components of the airbag or belt tensioner systems are scrapped. These
requirements are known to qualified dealerships.

Accessories, parts replacement and modifications 286
xNever mount, fasten or fit objects such as drink holders or telephone
cradles over the covers of the airbag modules or within their radius of
action.
xObjects placed over the airbag covers, or within their radius of action,
could lead to serious injury or loss of life if the airbags are triggered.
Fluids and consumables
All vehicle fluids and consumables, such as notched belts, tyres, coolant
fluids, engine oils, spark plugs and batteries are continually being devel-
oped. Therefore all fluids and consumables should be changed at a qualified
workshop. Qualified workshops are permanently informed of any modifica-
tions.
WARNING
The incorrect use or handling of fluids or consumables may result in acci-
dent, serious injury, burns or intoxication.
xTherefore, fluids must always be stored closed in their original
container.
xNever store fluids in empty food containers or bottles as other people
may accidentally drink the fluid.
xKeep all fluids and consumables out of reach of children.
xRead and observe the information and warnings given on the fluid
containers.
xOnly work in the open air or in well-ventilated zones, when using prod-
ucts which give off harmful vapours.
xNever use fuel, turpentine, engine oil, acetone or any other volatile
liquid in the maintenance of the vehicle. These are toxic and highly flam-
mable. They could lead to fire or explosions!
Caution
xOnly use appropriate fluids. Never mix the fluids. Failure to observe this
point will result in serious malfunctions and engine damage!
xAccessories and other components mounted in front of the air inlet
reduce the cooling effect of the coolant. If the engine is running under great
strain in high outside temperatures, it could overheat.
For the sake of the environment
Leaking fluids could pollute the environment. Collect any spilt fluids in suit-
able containers and dispose of in accordance with legislation and with
respect for the environment.
Repairs and technical changes
When performing repairs and technical modifications, SEAT's directives
must be observed! Ÿ
Unauthorised modifications to the electronic components or software in the
vehicle may cause malfunctions. Due to the way the electronic components
are linked together in networks, other indirect systems may be affected by the
faults. This may significantly affect the vehicle's performance, increase
component wear and could mean that the vehicle registration documents are
no longer valid.
Your Technical Service cannot be held liable for any damage caused by tech-
nical modifications or repairs performed incorrectly.
WARNING (continued)WARNING (continued)