brake light Seat Alhambra 2010 Owner's Guide

Checking and refilling levels 296
Closing the tank cap
xScrew on the tank cap clockwise until it you hear it click into position.
xPress the tank flap until you hear it click into place. The tank flap must be
flush with the body contour.
WARNING
Do not continue refilling once the fuel nozzle has switched itself off. The
fuel tank may be filled too much. As a result, fuel may spurt out and spill.
This could lead to a fire, explosion and severe injuries.
Caution
xAlways remove any fuel spilled on the vehicle paintwork immediately to
avoid damage to the wheel housing, the tyre and vehicle paintwork.
For the sake of the environment
Spilt fuel can contaminate the environment.
Refilling precautions
Information on bulb replacement Ÿpage 360.
Checklist
Never work on the engine or in the engine compartment if you are not familiar
with the operations to be carried out, the applicable safety standards and
especially if you do not have the instruments, liquids and tools necessary
Ÿpage 304, “Working in the engine compartment”! Have the work carried
out by a qualified workshop if you are uncertain. Check the following regu-
larly, preferably when you refuel:
xWindscreen washer fluid level Ÿpage 124
xEngine oil level Ÿpage 309
xEngine coolant level Ÿpage 313
xBrake fluid level Ÿpage 210
xTyre pressure Ÿpage 323
xVehicle lighting required to guarantee road safety:
–Indicators
– Side lights, dipped headlights and full beam headlights
– Rear lights
–Brake lights
– Rear fog light Ÿpage 116
WARNING
Not following the checklist prepared for your own safety could lead to acci-
dents and severe injuries.
xAlways follow the check list and perform the necessary operations.

Checking and refilling levels 316
Preparations
xPark the vehicle on even, flat and firm ground.
xAllow the engine to cool Ÿ.
xOpen the bonnet ’ Ÿpage 304.
xThe coolant expansion reservoir is easily recognisable because of the
symbol « on the cap Ÿpage 315, fig. 179.
Checking the engine coolant level
xWhen the engine is cold, check the coolant level using the side marking
on the expansion reservoir Ÿpage 315, fig. 178.
xIf the level is below the “MIN” mark, top up with coolant. When the engine
is hot it may be slightly above the marked area.
Topping up the engine coolant level
xAlways protect your face, hands and arms from hot coolant and steam
using a large, thick cloth over the coolant expansion tank cap.
xRemove the cap very carefully Ÿ.
xOnly refill using new engine coolant according to SEAT specifications
(Ÿpage 314) Ÿ.
xThe engine coolant level should be between the marks on the coolant
expansion tank Ÿpage 315, fig. 178. Do not exceed the top level of the
marked area Ÿ.
xScrew on the cap tightly.
xIf, the event of an emergency, you have no coolant that is compliant to the
required specifications (Ÿpage 314), never use another type of additive.
Instead, first top up with distilled water Ÿ only. Then re-establish the
correct proportion of the mixture with the correct additive as soon as possible
Ÿpage 314.
WARNING
Hot vapours and coolant can cause serious burns.
xNever open the coolant expansion tank if steam or coolant is coming
from the engine compartment. Wait until you cannot see or hear any steam
or coolant escaping.
xAlways wait until the engine has completely cooled before very care-
fully opening the expansion tank cap. Contact with hot elements of the
engine can cause skin burns.
xOnce the engine has cooled, follow the instructions below before
opening the bonnet:
Turn on the electronic parking brake and place the gear selector lever
in P or the gear stick in neutral.
Remove the key from the ignition.
Keep children away from the engine compartment and never leave
them unsupervised.
xWhen the engine is warm or hot, the cooling system is pressurised! Do
not unscrew the cap on the expansion tank when the engine is hot. Other-
wise, coolant may spray out under pressure causing burns and serious
injury.
Carefully and slowly unscrew the cap anticlockwise, gently pressing
down on it.
Always protect your face, hands and arms from hot coolant and
steam using a large, thick cloth.
xWhen refilling liquids, avoid spilling them on parts of the engine and
the exhaust system. Spilled liquids could cause a fire. Under specific
circumstances, the ethylene glycol can catch fire.
Caution
xTop up with distilled water only. Any other type of water may lead to
considerable rusting in the engine due to its chemical components. This
could consequently damage the engine. If you have not used distilled water
WARNING (continued)

Wheels and tyres339
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Changing a wheel*
Introduction
The tyres mounted on the vehicle are anti-puncture. The wheels should only
be changed when switching from summer to winter tyres or vice-versa. The
tools required for changing a wheel are only supplied with the vehicle if the
vehicle is supplied from the factory with winter tyres. If this is not the case,
please take the vehicle to a specialised workshop to have the wheels
changed.
You should only change the wheels yourself if the vehicle is parked in a safe
place, you are familiar with the procedure and you have all the necessary
tools! Otherwise, you should seek professional assistance.
Additional information and warnings:
xVehicle key set Ÿpage 78
xWheels and tyres Ÿpage 323
xWheel trims Ÿpage 336
xVehicle tools Ÿpage 353
WARNING
Changing a wheel can be dangerous, especially on the hard shoulder.
Please observe the following rules to minimise the risk of injury:
xStop the vehicle safely as soon as possible. Park your vehicle as safe
distance from surrounding traffic to change a wheel.
xWhen changing a wheel, keep all passengers and particularly children
a safe distance away from the work area.
xTurn on the hazard warning lights to warn other road users.
xEnsure the ground on which you park is flat and solid. If necessary,
support the jack on a wide solid base.
xIf you are changing a wheel yourself, you should be familiar with the
required procedure. Otherwise, you should seek professional assistance.
xOnly use suitable tools that are not damaged when changing a wheel.
xAlways stop the engine, turn on the electronic parking brake and place
the gear selector lever in position P, for an automatic gearbox, or engage a
gear for a manual gearbox to reduce the risk of the vehicle moving acciden-
tally.
xHave the tightening torque of the wheel bolts checked as soon as
possible with a reliable torque wrench.
Preparations for changing a wheel
Check list
Before changing a wheel, complete the following operations in the order
given Ÿ:
1. Park the vehicle on an even and solid surface.
2. Connect the electronic parking brake Ÿpage 210.
3. Automatic gearbox: Move selector lever to position P Ÿpage 201.
4. Stop the engine and remove the key from the ignition Ÿpage 195.
5. Manual gearbox: Select a gear Ÿpage 201.
6. Have all vehicle occupants get out of the vehicle and wait in a safe place
(for example, behind the safety barrier).
7. Block the opposite wheel with two folding wedges taken from the vehicle
tool kit Ÿpage 354, fig. 208 or similar objects.
8. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
9. If the luggage compartment is full: take the baggage out of the vehicle.
WARNING (continued)

If and when 346
3. Connect the electronic parking brake Ÿpage 210.
4. Move the selector lever to its intermediate position or to P Ÿpage 201.
5. Stop the engine and remove the key from the ignition Ÿpage 195.
6. Have all occupants leave the vehicle and move to safety, for example
behind a guard rail.
7. When leaving the vehicle, take all keys with you.
8. Place an emergency warning triangle to indicate the position of your
vehicle to other road users.
9. Allow the engine to cool and check if a specialist is required.
Examples of when to use the hazard warning lights:
xIf the vehicles ahead suddenly slow down or reach the end of a traffic jam,
to warn the vehicles behind.
xIn case of an emergency.
xIf the vehicle breaks down.
xWhen being towed.
Always comply with the applicable laws regarding the use of hazard warning
lights.
If the hazard warning lights are not working, you must use an alternative
method of drawing attention to your vehicle. This method must comply with
traffic legislation.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire and considerable damage.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as dried grass or fuel).
Note
The vehicle battery will discharge and run down if the hazard warning lights
remain on for too much time (even with the ignition turned off).
Note
For some vehicles, the brake lights will blink when braking suddenly at
speeds of approximately 80 km/h to warn vehicles behind. If braking
continues, then the hazard warning lights will automatically be turned on at
the speed of less than approximately 10 km an hour. The brake lights remain
lit. Upon accelerating, the hazard warning lights will be automatically turned
off.

If and when361
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Indicator
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Checking the bulbs of a trailer
For vehicles with the factory fitted trailer system, certain trailer lights are also
controlled if the socket is correctly connected.
A fault on a trailer turn indicator is indicated on the instrument panel by the
indicator blinking twice as fast (
 or
) Ÿpage 113.
xGeneral fault of all indicators on one side.
xFault in one tail light (on some models, also the registration light).
xFault in two brake lights.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Note
A fault in the LED on the tail lights will not be indicated. However, if the fault
affects all the LEDs then this will be indicated by the indicator .
Information for replacing bulbs
Checklist
To replace a bulb, carry out the following operations always in the order given
Ÿ:
1. Park the vehicle a safe distance from traffic and on suitable ground.
2. Connect the electronic parking brake Ÿpage 210.
3. Turn the light switch to position 0 Ÿpage 113.
4. Move the gear lever into the neutral position Ÿpage 113.
5. Automatic gearbox: Move selector lever to position P Ÿpage 201.
6. Stop the engine and remove the key from the ignition Ÿpage 195.
7. Manual gearbox: Select a gear Ÿpage 201.
8. Wait until all of the passenger compartment lights are turned off
Ÿpage 113.
9. Allow the corresponding bulb to cool.
10. Visually inspect fuses to see if any are blown Ÿpage 356.
11. Replace the bulb according to the instructions Ÿ. Bulbs should only
be replaced by new identical models. Bulb information is displayed on
the bulb socket or on the bulb itself.
12. In general, never touch the bulb glass directly. The heat of the bulb would
cause the fingerprint to evaporate and condense on the reflector. This
will impair the brightness of the headlight.
lights upPossible causeSolution
A vehicle exterior lighting
bulb is not working.Replace the faulty bulb.

If and when373
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The vehicles should not touch. Otherwise, current may be allowed to flow
when the positive poles are connected.
Connect the clamps so they have good metal-to-metal contact with the termi-
nals.
If the engine fails to start straight-away, switch off the starter after about 10
seconds and try again after about a minute.
Complete operations only in the sequence given.
Jump lead terminal connections
xSwitch off the ignition of both vehicles Ÿpage 195.
xLikewise, open the battery cover in the engine compartment Ÿpage 318,
or remove the positive pole cap from one side 3), in the direction of the arrow
Ÿpage 372, fig. 225.
xConnect one end of the red jump lead to the positive terminal
Ÿpage 372, fig. 226 or Ÿpage 372, fig. 225 of the vehicle with the
flat battery Ÿ.
xConnect the other end of the red jump lead to the positive terminal in
the vehicle providing assistance .
xFor vehicles without Start-Stop system: Connect one end of the black
jump lead to the negative terminal in the vehicle providing assistance
Ÿpage 372, fig. 226.
xFor vehicles with Start-Stop system: Connect one end of the black
jump lead to a suitable ground connection, a solid piece of metal in the
engine block, or to the engine block Ÿpage 372, fig. 227.
xConnect the other end of the black jump lead to a solid metal compo-
nent connected to the engine block, or onto the engine block itself of the
vehicle with the flat battery however, connect it as far away as possible from
the battery Ÿ.
xPlace the leads so that they cannot be caught by any moving parts in the
engine compartment.Switching on
xStart the engine of the vehicle supplying current and let it run at idling
speed.
xStart the engine of the car with the flat battery and wait two or three
minutes until the engine is “running smoothly”.
Removing the jump leads
xBefore you remove the jump leads, switch off the headlights (if they are
switched on).
xTurn on the heating and rear window heater in the vehicle with the flat
battery. This helps minimise voltage peaks which are generated when the
leads are disconnected.
xWith the engines running, disconnect the leads in reverse order to
connection.
xClose the battery cover, or replace the positive pole cap 3).
WARNING
Incorrectly jump starting could cause the battery to explode resulting in
serious injury. Please observe the following rules to minimise the risk of a
battery explosion:
xAll work involving the vehicle battery and electrical system can cause
corrosion, fire and serious electric shocks. Always read and take into
account the safety warnings and standards before beginning work on the
battery Ÿpage 318, “Vehicle battery”.
xAlways protect your eyes with suitable working goggles and never lean
over the vehicle battery.
xThe jump leads must be connected in the correct order: first the positive
cable, then the negative cable.
xDo not attach the negative cable to parts of the fuel system or to the
brake hose/pipe.
3)Vehicles whose battery is not located in the engine compartment Ÿpage 372.
A+A+AA
A+AB
A-AB
AX
AX
AA

If and when375
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Towing and tow starting
Introduction
When towing, always respect legal requirements.
For technical reasons, it is not possible to tow a vehicle if the battery is flat.
Additional information and warnings:
xElectronic power control and exhaust gases purification system
Ÿpage 255
WARNING
A vehicle with a flat battery should never be towed.
xNever remove the key from the ignition lock. The electronic steering
lock could engage. Then the vehicle will be uncontrollable. You may lose
control of the vehicle and there is a risk of serious accident.
WARNING
When towing the vehicle, the handling and braking efficiency change
considerably. Please observe the following instructions to minimise the
risk of serious accidents and injury:
xAs the driver of the vehicle being towed:
The brake must be depressed must harder as the brake servo does
not operate. Always remain aware to avoid collision with the towing
vehicle.
More strength is required at the steering wheel as the power
steering does not operate when the engine is switched off.
xAs the driver of the towing vehicle:
Accelerate gently and carefully.Avoid sudden braking and manoeuvres.
Brake well in advance than usual and brake gently.
Caution
xCarefully fit and remove the towing ring and its cover to avoid damage to
the vehicle (for example, paintwork).
xWhen towing, fuel could enter the catalytic converter and cause
damage!
Instructions for tow starting
In general, the vehicle should not be started by towing. Jump-starting is
much more preferable Ÿpage 371.
For technical reasons, the following vehicles can not be tow started:
xVehicles with an automatic gearbox.
xVehicles with the KESSY locking and ignition system, given that the elec-
tronic steering lock will certainly not be unlocked.
xVehicles with an electronic parking brake, given that it is possible that the
brake will not be disengaged.
xIf the vehicle battery is flat, it is possible that the engine control units do
not operate correctly.
However, if your vehicle must absolutely be tow-started (manual gearbox):
xEngage 2nd or 3rd gear.
xKeep the clutch pressed down.
xSwitch on the ignition and the hazard warning lights.
xRelease the clutch when both vehicles are moving.
WARNING (continued)

If and when 376
xAs soon as the engine starts, press the clutch and move the gear lever into
neutral. This helps to prevent a collision with the towing vehicle.
Caution
When tow-starting, fuel could enter the catalytic converter and damage it.
Towing instructions
Tow-rope or tow-bar
When towing, the tow bar is the safest and vehicle friendly way. You should
only use a tow-rope if you do not have a tow-bar.
A tow-rope should be slightly elastic to avoid damage to both vehicles. It is
advisable to use a tow-rope made of synthetic fibre or similarly elastic mate-
rial.
Only secure the tow rope or tow bar to the tow ring or specially designed
fitting.
Vehicles with a factory fitted towing device, can only be used for towing with
a tow-bar, specially designed to fit on a tow hitch ball Ÿpage 260.
Towing vehicles with an automatic gearbox
Note the following for a towed vehicle:
xMake sure the gear selector lever is in the N position.
xDo not drive faster than 50 km/h (30 mph) when towing a vehicle.
xDo not tow further than 50 km (30 miles).
xIf a breakdown truck is used, the vehicle must be towed with the front
wheels raised. Note the following instructions for towing four wheel drive
vehicles.Instructions for towing four-wheel-drive vehicles
Four wheel drive vehicles can be towed using a toolbar or tow rope. If the
vehicle is towed with the front or rear axle raised, the engine must be turned
off to avoid transmission damage.
For vehicles with a double clutched DSG
® (direct shift gearbox) the instruc-
tions for towing vehicles with an automatic gearbox apply Ÿpage 376.
Situations in which the vehicle should not be towed
In the following cases, the vehicle should not be towed but transported on a
trailer or special vehicle:
xIf the vehicle gearbox does not contain lubricant due to a fault.
xIf the vehicle battery is flat and, as a result, the electronic steering lock
and electronic parking brake cannot be disengaged if applied.
xIf the vehicle to be towed has an automatic gearbox and the distance to
be covered is greater than 50 km (30 miles).
Note
The vehicle can only be towed if the electronic parking brake and steering
lock are deactivated. If the vehicle has no power supply or there is an electric
system fault, the engine must be started using jump leads to deactivate the
electronic parking brake and electronic steering lock.

If and when 378
xScrew in the tow ring into its position anticlockwise as far as it will go
Ÿ. Use a suitable tool to firmly tighten the tow ring in its location.
xAfter towing, remove the tow ring by turning it clockwise and put the cover
back in place.
Caution
xThe tow ring must always be completely and firmly tightened. Otherwise,
it could be released while towing and tow-starting.
xVehicles with a factory fitted towing device, can only be used for towing
with a tow-bar, specially designed to fit on a tow hitch ball. Otherwise, the tow
hitch ball and the vehicle may be damaged. Otherwise, a tow rope should be
used.
Towing advice
Towing requires some experience, especially when using a tow-rope. Both
drivers should be familiar with the technique required for towing. For this
reason, inexperienced drivers should abstain.
While driving, avoid excessive traction forces and jerking. When towing on an
unpaved road, there is always a risk of overloading and damaging the
anchorage points.
If the vehicle is towed, with the hazard warning lights on and the ignition
switched on, the turn signal may be used to indicate changes of direction.
Simply operate the turn indicator lever as usual. Meanwhile, the hazard
warning lights will go off. When the turn signal lever is returned to the rest
position, the hazard warning lights will be turned on automatically.
Notes for the driver of the towed vehicle
xLeave the ignition on to avoid locking the steering wheel, to release the
electronic parking brake and to activate the turn signal indicators, the horn
as well as the window wipers and window washers.
xAs the power assisted steering does not work if the engine is not running,
you will need more strength to steer than normally.
xThe brake must be depressed must harder as the brake servo does not
operate. Avoid hitting the towing vehicle.
xNote the instructions and information contained in the instruction manual
for the vehicle to be towed.
Notes for the driver of the towing vehicle
xAccelerate gently and carefully. Avoid sudden manoeuvres.
xBrake well in advance than usual and brake gently.
xNote the instructions and information contained in the instruction manual
for the vehicle to be towed.

Index393
Index
"Safe" security system . . . . . . . . . . . . . . . . . . . . 88
A
Abroad
Extended stay abroad with your vehicle . . 283
Sale of vehicle . . . . . . . . . . . . . . . . . . . . . . . 283
ABS
See "Braking assist systems" . . . . . . . . . . . 216
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
Adaptive headlights
Adaptive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
AdBlue
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . 300
Information . . . . . . . . . . . . . . . . . . . . . . . . . 301
Minimum quantity for a refill . . . . . . . . . . . 301
Refilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Specifications . . . . . . . . . . . . . . . . . . . . . . . 303
Tank filling capacity . . . . . . . . . . . . . . . . . . . 301
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 300
Additional equipment . . . . . . . . . . . . . . . . . . . . 286
Additional heater
See "Auxiliary heater" . . . . . . . . . . . . . . . . . 187
Adjusting passenger exterior mirror . . . . . . . . . 132
Adjustment
Correct sitting position . . . . . . . . . . . . . . . . . 12
Electric front seat . . . . . . . . . . . . . . . . . . . . . 135Head restraints . . . . . . . . . . . . . . . . . . . . . . 143
Mechanical front seat . . . . . . . . . . . . . . . . . 134
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Seat with position memory . . . . . . . . . . . . . 138
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . 194
Adjustments
Folding the backrest of the front passenger's
seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Headlight range . . . . . . . . . . . . . . . . . . . . . . 120
Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Aerial built into the window . . . . . . . . . . . . . . . 283
AFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Air conditioning
see "Climate control" . . . . . . . . . . . . . . . . . 179
Air recirculation mode . . . . . . . . . . . . . . . . . . . . 185
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . 29, 33
Cleaning instrument panel . . . . . . . . . . . . . 281
Curtain airbags . . . . . . . . . . . . . . . . . . . . . . . 40
Deactivating the front passenger airbag . . . 36
Deactivating using the key switch . . . . . . . . 36
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Differences between front passenger airbag
systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . . 34
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Knee airbag . . . . . . . . . . . . . . . . . . . . . . . . . . 41Locking the vehicle after airbag deployment . .
84
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Use of child seats . . . . . . . . . . . . . . . . . . . . . 36
Vehicle care . . . . . . . . . . . . . . . . . . . . . . . . . 281
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 31
Alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Alcantara . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
All-wheel drive
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . . 332
Winter tyres . . . . . . . . . . . . . . . . . . . . . . . . . 331
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Ambient lighting . . . . . . . . . . . . . . . . . . . . . . . . 121
Anodized surfaces . . . . . . . . . . . . . . . . . . . . . . . 275
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Anti-lock brake system (ABS) . . . . . . . . . . . . . . 216
Antitheft alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Antitheft alarm system
Anti-tow system . . . . . . . . . . . . . . . . . . . . . . . 90
False alarms . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Interior monitoring . . . . . . . . . . . . . . . . . . . . 90
Antitheft bolts . . . . . . . . . . . . . . . . . . . . . . . . . . 354
Anti-theft locking bolts . . . . . . . . . . . . . . . . . . . 339
Anti-theft wheel locking bolts . . . . . . . . . . . . . . 340
Anti-tow system . . . . . . . . . . . . . . . . . . . . . . . . . . 90