maintenance Seat Alhambra 2010 Owner's Guide

Checking and refilling levels297
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Fuel
Introduction
You will find a factory-fitted sticker containing information on the type of fuel
for your vehicle on the inside of the fuel tank flap.
Additional information and warnings:
xŸBooklet “Maintenance Programme”
xRefuelling Ÿpage 293
xEngine and exhaust system management Ÿpage 255
WARNING
Refuelling or handling fuel carelessly can cause an explosion or fire
resulting in serious burns and injuries.
xFuel is a highly explosive, easily flammable substance.
xObserve current safety instructions and local regulations concerning
the handling of fuel.
Types of fuel
The type of fuel to use when refilling will depend on the vehicle's engine. You
will find a factory-fitted sticker containing information on the type of fuel for
your vehicle on the inside of the fuel tank flap.
SEAT recommends the use of sulphur-free or low sulphur fuel to reduce
consumption and prevent engine damage.
Petrol
Petrol types
Vehicles with petrol engines must refuel using unleaded petrol according to
European norm EN 228 Ÿ.
Petrol types are categorised according to their octane number (e.g. 91, 95, 98
or 99 RON (RON = “Research Octane Number”). You may use petrol with a
high octane number than the one recommended for your engine. However,
this has no advantage in terms of fuel consumption and engine power.
SEAT recommends refuelling with a low sulphur content or sulphur-free petrol
to reduce petrol consumption for petrol engines.
Petrol additives
The quality of the fuel influences running behaviour, performance and service
life of the engine. For this reason, you should use good quality petrol
containing a mixture of additives. These additives will help to prevent corro-
sion, keep the fuel system clean and prevent deposits from building up in the
engine.
Possible types of
fuelAlternative namesFurther information
91a) RON
a)RON = Regulation Octane Number
Normal petrol, normal
unleaded petrol
Ÿpage 29795a) RONPremium unleaded petrol (95
RON)
98a) RONPremium unleaded petrol (98
RON)
DieselŸpage 298

Checking and refilling levels 298
If good quality petrol with additives is not available or engine problems arise,
the necessary additives must be added when refuelling.
Not all petrol additives have been shown to be effective. The use of unsuit-
able petrol additives could damage the engine. These additives are available
from qualified workshops, who will inform you of their application.
Caution
xOnly use fuel with an octane rating that is in line with the norm EN 228,
otherwise significant damage could be caused to the engine and fuel system.
Furthermore, it could lead to a loss of performance with the consequent
engine fault.
xThe use of unsuitable petrol additives could damage the engine.
xIf, in exceptional circumstances, petrol with a lower octane rating to that
recommended is used, only use moderate engine speeds and a light throttle.
Avoid using full throttle and overloading the engine. Otherwise you may
damage the engine. Fill up with fuel of a suitable octane rating as soon as
possible.
xDo not refuel if the filler indicates that the fuel contains metal. LRP (lead
replacement petrol) fuels also contain high concentrations of metal addi-
tives. This could damage the engine!
xJust one full tank of leaded fuel would seriously impair the efficiency of
the catalytic converter and could damage it.
Diesel
Diesel fuel
Diesel fuel must correspond to European standard EN 590 (In Germany, EN
590 or DIN 51628).
The use of diesel fuel with a high sulphur percentage requires shorter service
intervals ŸBooklet “Maintenance Programme” Ÿ. Your qualified work-shop will be able to tell you which countries have diesel with a high sulphur
content.
Do not mix fuel additives (thinners, or similar additives) with diesel fuel.
Winter-grade diesel
When using “summer-grade diesel fuel”, difficulties may be experienced at
temperatures below 0 °C (+32 °F) because the fuel thickens due to wax sepa-
ration. For this reason, “winter-grade diesel fuel” is available in Germany, for
example, during the cold months. It can be used at temperatures as low as
-20 °C (-4 °F).
In countries with different climatic conditions, other types of diesel fuel are
available that are suitable to local temperatures. SEAT qualified workshops
and filling stations in the country concerned will inform you on the type of
diesel fuels available.
A cold diesel engine makes more noise during winter temperatures than
summer temperatures. Furthermore, the exhaust fumes may turn slightly
bluish while the engine is heating. The quantity of exhaust gases will depend
on the outside temperature.
Filter pre-heater
Vehicles with a diesel engine are fitted with a fuel filter pre-heater. This
ensures that the fuel system remains operational to approx. -24 °C (-11.2 °F),
provided you use winter-grade diesel which is safe to -15 °C (+5.00 °F).
However, if the fuel has waxed to such an extent that the engine will not start
at temperatures of under -24 °C (-11.2 °F), simply place the vehicle in a warm
garage or workshop for a while to heat up.
Auxiliary heater
Vehicles with a diesel engine may be fitted with an auxiliary heater. The
heater runs off the fuel from the fuel tank. On doing so, smells and steam may
be noticed outside the vehicle for a short period. This is normal and it is not
an indication of a fault in the vehicle.

Checking and refilling levels 300
Selective Catalytic Reduction* (AdBlue)
Introduction
The AdBlue fill level must be checked when the vehicle is being serviced
ŸBooklet “Maintenance Programme”.
Additional information and warnings:
xLuggage compartment Ÿpage 146
xFuel Ÿpage 297
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
If the AdBlue fill level is too low, the vehicle may not restart after switching
the ignition off. The emergency start or jump start will not be possible
either!
xTop up with AdBlue at the latest 1000 km or 600 miles before it runs
out.
xDo not allow the AdBlue to run too low.
WARNING
AdBlue is an irritant, corrosive liquid that can cause injuries if it touches
the skin, eyes or respiratory organs.
xIf AdBlue get in contact with eyes and skin, rinse for at least 15 minutes
with plenty of water and seek medical help.
xIf the AdBlue is swallowed, wash the mouth with plenty of water for at
least 15 minutes. Do not try to provoke vomiting unless recommended by a
Doctor. Seek medical advice immediately.
Caution
AdBlue damages surfaces such as painted vehicle parts, plastic, items of
clothing and carpets. Spilt AdBlue should be removed as quickly as possible
using a damp cloth and plenty of cold water.
xIf the AdBlue has crystallised, remove with warm water and a sponge.
Control and warning lamps
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
lights upPossible cause ŸSolution
b (red)The engine cannot be
restarted! The level of AdBlue
is too low.Stop the vehicle in a suitable,
safe and flat area then top up
with the minimum quantity of
AdBlue required Ÿpage 302.
b (red)
with
>
The engine cannot be
restarted! AdBlue system
malfunction.Contact a specialist workshop.
Have the system checked there.
b (yel-
low)The AdBlue reserve is low.
Refill AdBlue over the next kilo-
metres or miles as indicated
Ÿpage 302. SEAT recommends
contacting a specialist work-
shop.
b (red)
with

>
There is a fault in the AdBlue
system or unsuitable AdBlue
fluid has been used.Contact a specialist workshop.
Have the system checked there.

Checking and refilling levels309
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Engine oil
Introduction
Additional information and warnings:
xŸBooklet “Maintenance Programme”
xWorking in the engine compartment Ÿpage 304
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Incorrectly handling engine oil can cause injury and serious burns.
xAlways protect your eyes when handling engine oil.
xOil is toxic and must be kept out of the reach of children.
xEngine oil must only be kept closed in its original container. The same
applies to use oil until it has been disposed of.
xNever store engine oil in empty food containers or bottles as other
people may accidentally drink it.
xRegular contact with engine oil can be bad for the skin. If you come into
contact with engine oil, wash your skin with soap and water.
xWith the engine running, the engine oil gets extremely hot and can
cause severe skin burns. Always wait until the engine has fully cooled.
For the sake of the environment
Similar to the other service liquids, spilled engine oil can be bad for the envi-
ronment. Collect any spilt fluids in suitable containers and dispose of in
accordance with legislation and with the utmost respect for the
environment.
Warning and control lamps
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
lights upPossible causeSolution
Insufficient engine oil.Switch the engine off. Check the
engine oil level Ÿpage 310.
flashesPossible causeSolution
EEngine oil pressure too low.
› Stop the vehicle!
Switch off the engine. Check the
engine oil level.
- If the warning indicator flashes
although the oil level is correct,
do not continue driving or leave
the engine running. Otherwise,
the engine could be damaged.
You should obtain professional
assistance.
Engine oil sensor faulty.Contact a specialist workshop.
Have the engine oil sensor
checked.

Checking and refilling levels 312
Engine oil consumption
The consumption of engine oil can be different from one engine to another
and can vary during the useful life of the engine.
Depending on driving style and the conditions of use, the consumption of
engine oil can reach 1 litre every 2,000 km (one quarter of a gallon every
1,200 miles); for new vehicles, this could be higher for the first 5,000 km
(3,000 miles). For this reason the engine oil level must be checked at regular
intervals, preferably when filling the tank and before a journey.
When the engine is working hard, for instance during sustained high-speed
motorway cruising in summer, when towing a trailer or climbing mountain
passes, the oil level should preferably be kept within area Ÿpage 310,
fig. 175 .
Changing the engine oil
The engine oil must be changed regularly according to the specifications of
the Maintenance Programme.
Due to the problems linked with disposing of used oil and the need for suit-
able tools and special knowledge, always visit a qualified workshop to have
the engine oil and filter changed. SEAT recommends visiting a qualified work-
shop.
Detailed information on the service intervals are shown in the Maintenance
Programme.
Engine oil additives make new oil darker after the engine has been running
for a short period. This is normal and does not mean more frequent oil
changes are required.
WARNING
If, in exceptional circumstances, you must change the engine oil yourself,
please note the following:
xWear eye protection.
xAlways wait until the engine has completely cooled to avoid being
burned.
xAlways keep your arms horizontal when unscrewing the oil drainage
bolt so that the oil does not run down your arms when it begins to drain.
xUse a suitable and large enough container to collect all of the used oil
in the engine.
xNever collect engine oil in empty food containers, cans, bottles and
other containers as not all people are able to identify engine oil.
xOil is toxic and must be kept out of the reach of children.
For the sake of the environment
Before changing the engine oil, find a suitable location or service for proper
disposal.
For the sake of the environment
Always dispose of engine oil with the utmost respect for the environment.
Never dispose of used engine oil in places such as a garden, woods, drains,
roads, paths, rivers and drainage systems.
AA

Checking and refilling levels 318
Vehicle batter y
Introduction
The battery is a component of the vehicle's electrical system.
Never work on the electrical system without fully understanding the opera-
tions required, the applicable safety standards and without the correct tools
Ÿ! Have the work carried out by a qualified workshop if you are uncertain.
SEAT recommends visiting a qualified workshop. Negligent work can cause
serious injury.
Location and number of batteries in the vehicle
The battery is located in the engine compartment.
Explanation of the warning indications on the vehicle's battery
Additional information and warnings:
xŸBooklet “Maintenance Programme”
xStarter assist systems (Start-Stop function) Ÿpage 221
xWorking in the engine compartment Ÿpage 304
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Working on the vehicle battery and the electrical system can cause corro-
sion, fire and electric shocks. Always read and take into account the
following warnings and safety standards before carrying out any work:
xBefore working on the battery, switch off the engine, the ignition and
all electrical devices then disconnect the negative connection on the
battery.
xKeep children away from acid and the battery itself!
xWear eye protection.
xBattery acid is very corrosive and caustic. It can burn skin and cause
blindness. When handling the battery, protect yourself from splashes of
acids, above all your hands, arms and face.
xDo not smoke and never work close to places exposed to flames or
sparks.
xAvoid sparks and electrostatic discharges when working with cables
and electrical devices.
xNever short the battery terminals.
xNever use a damaged battery. It can explode. Replace a damaged
battery immediately.
xReplaced damaged or frozen batteries as soon as possible. A flat
battery can freeze at temperatures around 0°C (+32 °F).
xVehicles with the battery in the luggage compartment: Ensure that the
battery ventilation hose is correctly secured.
Caution
xNever disconnect the battery if the ignition is switched on or if the engine
is running. This could damage the electrical system or electronic compo-
nents.
SymbolMeaning
Wear eye protection!
Battery acid is very corrosive and caustic. Always wear
protective gloves and eye protection!
ŽFires, sparks, naked lights and smoking are prohibited.
ŸA highly explosive mixture of gases is released when the
battery is under charge.
Keep children away from acid and batteries!

Checking and refilling levels319
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xDo not expose the battery to direct sunlight over a long period of time, as
the intense ultraviolet radiation can damage the battery housing.
xIf the car is left standing for long periods, protect the battery from extreme
cold temperature so that it does not “freeze up” and become damaged.
Warning lamp
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Checking the electrolyte level of the vehicle battery
The battery's electrolyte level should be checked regularly in high-mileage
vehicles, in hot countries and in older batteries. Other batteries do not
require maintenance.
lights upPossible causeSolution
FFaulty generator.
Contact a specialist workshop.
Have the electrical system
checked.
Disconnect any unnecessary
electrical consumers. The gener-
ator does not charge the battery
while the vehicle is in motion.
Fig. 180 In the engine
compartment: Remove
the cover from the
vehicle's battery.
Fig. 181 In the engine
compartment: Unfold the
vehicle's battery hose.

Checking and refilling levels 320
Start-Stop systems Ÿpage 223 are equipped with a special battery labelled
“AGM”. For technical reasons, it is not possible to check the electrolyte level
of these batteries
Preparations
xPrepare the vehicle for work in the engine compartment Ÿpage 304
xOpen the bonnet ’ Ÿpage 304.
Opening the battery cover
The battery covers are different depending on the engine size of the vehicle:
xIn the case of a cover: press the tab Ÿpage 319, fig. 180 in the direc-
tion of the arrow and pull the cover upwards.
xIn the case of a hose: fold the cover to one side to remove Ÿpage 319,
fig. 181.
Checking the battery electrolyte level
xMake sure there is sufficient lighting to clearly recognise the colours.
Never use open flames or sparklers as a light source.
xDepending on the level of acid, the Magic eye on the top of the battery will
change colour.
WARNING
Working with the vehicle battery involves a risk of corrosion, explosions
and electric shock.
xAlways wear protective gloves and eye protection.
xBattery acid is very corrosive and caustic. It can burn skin and cause
blindness. When handling the battery, protect yourself from splashes of
acids, above all your hands, arms and face.
xNever tilt the vehicle battery. Battery acid could spill out of the open-
ings to release gases and cause corrosion damage.
xNever open the vehicle battery.
xIf battery acid splashes on you, immediately rinse your eyes and skin
abundantly with water for several minutes. Then seek medical care imme-
diately.
xIf acid is swallowed by mistake, consult a doctor immediately.
Charging, replacing and connecting or disconnecting the
battery
Charging the battery
The vehicle battery should be charged by a specialist workshop only, as
batteries using special technology have been installed and they must be
charged in a controlled environment Ÿ. SEAT recommends visiting a qual-
ified workshop.
Replacing a vehicle battery
The battery has been developed to suit the conditions of its location and has
special safety features. If the battery must be replaced, consult a qualified
SEAT workshop for information on electromagnetic compatibility, the size
and maintenance, performance and safety requirements of the new battery in
your vehicle before you purchase one. SEAT recommends you have the
battery replaced by a qualified SEAT workshop.
Use only maintenance-free genuine batteries conforming to TL 825 06 and
VW 7 50 73 Standards. These standards must be dated April 2008 or later.
Colour indicatorNecessary operations
light yellow or col-
ourlessThe electrolyte level of the vehicle's battery is too low.
Have the battery checked and, where applicable,
replaced by a specialist workshop.
Black indicationThe electrolyte level of the vehicle's battery is correct.
AA
WARNING (continued)

Checking and refilling levels321
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Start-Stop systems Ÿpage 223 are equipped with a special battery. There-
fore, it must only be replaced with a battery of the same specifications.
Disconnecting the vehicle's battery
If you must disconnect the battery from the electrical system, please note the
following:
xSwitch off the ignition and all electrical equipment.
xThe vehicle must be unlocked before disconnecting the battery, otherwise
the alarm will be triggered.
xFirst disconnect the negative cable and then the positive Ÿ.
Connecting the vehicle's battery
xBefore reconnecting the battery, switch off the engine, the ignition and
electric devices.
xFirst reconnect the positive cable and then the negative Ÿ.
Different control lamps may light up after connecting the battery and
switching the ignition on. They will be turned off after a short trip at a speed
of between 15 - 20 km/h (10 - 12 mph). If the warning indicators remain lit,
please visit a specialised workshop to have the vehicle checked.
If the battery has been disconnected for a long time, it is possible that the
next service date is not displayed or calculated correctly Ÿpage 64. Respect
the maximum service intervals permitted ŸBooklet “Maintenance
Programme”.
Vehicles with the KESSY system (Ÿpage 86): If, after connecting the battery,
the ignition cannot be switched on, lock and unlock the vehicle from outside.
Then try to switch the ignition back on. If the ignition can still not be switched
on, request the assistance of a specialist workshop.
Automatic consumer disconnection
The intelligent vehicle electrical system automatically implements a range of
measures to prevent the battery from discharging when high demands are
made on it:
xthe idling speed is increased so that the alternator provides more elec-
tricity.
xwhere necessary, the power of the most powerful consumers is reduced
or even completely disconnected.
xOn starting the engine, the power supply from the 12-volt sockets and the
cigarette lighter may be interrupted for a short time.
The on-board management program cannot always prevent the battery from
running flat. For example, if the ignition is left on for a long period with the
engine off or if the side lights or parking lights are left on while the vehicle is
stationary.
Why does the battery run flat?
xWhen stationary for a long time without starting the engine, particularly if
the ignition is switched on.
xUse of electrical consumers with the engine switched off.
xIf the auxiliary heater is running Ÿpage 187.
WARNING
Incorrectly securing the battery or using the wrong battery can cause
short-circuits, fire and serious injuries.
xAlways use only maintenance free batteries that do not run flat alone
and whose properties, specifications and size correspond to the standard
battery. The specifications are indicated on the battery case.
WARNING
A highly explosive mixture of gases is released when the battery is under
charge.
xThe batteries should be charged in a well-ventilated room only.
xNever charge a frozen or recently thawed battery. A flat battery can
freeze at temperatures around 0°C (+32 °F).

General notes on the technical data379
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Te c h n i c a l D a t a
General notes on the technical data
Outstanding information
Important
All data in the official vehicle documents take precedence
over this data.
All data provided in this manual are valid for the standard model in Spain. The
vehicle data card included in the Inspection and Maintenance Plan in the
vehicles registration documents show which engine is installed in the
vehicle.
The figures may be different depending on if additional equipment is fitted,
for different models, for special vehicles and for other countries.
Additional information and warnings:
xTransporting Ÿpage 13
xEcological driving Ÿpage 252
xFuel Ÿpage 297
xEngine oil Ÿpage 309
xEngine coolant Ÿpage 313
xWheels and tyres Ÿpage 323
xNotes for the user Ÿpage 283Abbreviations used in the Technical Data section
WARNING
Failure to observe requirements for weight, loads, dimensions and
maximum speed may lead to severe accident.
Abbrevia-
tionMeaning
kWKilowatt, engine power measurement.
PSPferdestärke (horsepower), formerly used to denote engine
power.
rpmRevolutions per minute - engine speed.
NmNewton metres, unit of engine torque.
l/100 kmFuel consumption in litres per 100 km.
g/kmCarbon dioxide emissions in grams per km travelled.
CO2Carbon dioxide
CNCetane number, indication of the diesel combustion power.
RONResearch octane number, indication of the knock resistance
of petrol.