wheel Seat Alhambra 2010 Service Manual

Driving 224
Important conditions for the engine to automatically switch off
xThe driver seat belt must be buckled.
xThe driver door must be closed.
xThe bonnet must be closed.
xThe factory-fitted towing bracket must not be electrically connected to a
trailer.
xA minimum engine temperature has been reached.
xThe vehicle has moved since the last stop.
xIn vehicles with Climatronic: The temperature inside the vehicle is within
the preset temperature range.
xThe temperature set is neither very high nor very low.
xThe air conditioning defrost function is not switched on.
xIn vehicles with Climatronic: the blower has not been manually set to a
high speed.
xThe power level of the vehicle's battery is sufficient.
xThe vehicle's battery temperature is neither too high nor too low.
xThe vehicle is not on a steep gradient or slope.
xThe front wheels are not overly turned.
xThe heated windscreen is not switched on.
xReverse gear is not engaged.
xThe park assist system is not switched on.
Conditions for automatically restarting the engine
The engine may automatically restart under the following conditions:
xIf the vehicle interior is too hot or too cold.
xIf the vehicle moves.
xIf the vehicle's battery voltage drops.
Conditions requiring the key to restart the engine
The engine must be started using the key under the following conditions:
xIf the driver unbuckles his/her seat belt.
xIf the driver's door is opened.
xIf the bonnet is opened.
xIn vehicles with a manual gearbox: If a gear has been selected.
Switching Start-Stop mode on and off manually
xPress the button on the centre console Ÿpage 223, fig. 147.
xThe button will light up when the Start-Stop function is switched off.
The engine will start immediately if the vehicle is in Stop mode when it is
switched off manually.
WARNING
The brake servo and the power steering do not work when the engine is
switched off.
xNever allow the vehicle to move when the engine is switched off.
Caution
Using the Start-Stop function for a long period at very high outdoor tempera-
tures could damage the vehicle's battery.
Note
In some cases, you may have to restart the vehicle using the key. Observe the
corresponding message on the instrument panel display.
›

Driving229
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Park Assist system*
Introduction
The Park Assist system helps the driver to find a suitable place to park, to
insert the vehicle into parallel and perpendicular parking places and to leave
parallel parking places.
The Park Assist system is limited to the system abilities and requires that the
driver is especially attentive Ÿ.
The parking sensor system is a component of the Park Assist system that
helps to park the vehicle.
For vehicles with the optical parking system, the radio navigation systems
screen displays the detected zones in front of and behind the vehicle, indi-
cating - within the limits of the system - the position of obstacles compared
to the vehicle.
The park assist system cannot be switched on if the factory-fitted towing
bracket is electrically connected to a trailer.
Additional information and warnings:
xBraking, stopping and parking Ÿpage 210
xParking sensor system Ÿpage 225
xCaring for and cleaning the vehicle exterior Ÿpage 269
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Despite the assistance provided by the park assist system, do not run any
risks when parking. The system is not a replacement for driver awareness.
xUnintentional movements of the vehicle could cause serious injury.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xThe surface of certain objects and items of clothing and external sound
sources may have a negative affect on the park assist signals or on the
system sensors or may not reflect its signals.
xThe sensors have blind spots in which obstacles and people are not
registered.
xAlways observe the area around the vehicle, as the sensors do not
always detect small children, animals or objects.
Caution
xThe park assist system aims exclusively at other parked vehicles, without
taking curbs or other circumstances into account. Make sure you do not
damage the tyres and wheel rims when parking. Where necessary, stop
manoeuvring to avoid damaging the vehicle.
xThe sensors may not always be able to detect objects such as trailer draw
bars, thin rails, fences, posts and trees, etc. This could result in damage to
your car.
xAlthough the parking sensor system detects and warns of the presence of
an obstacle, the obstacle could disappear from the angle of measurement of
the sensors if it is too high or low and the system would no longer indicate it.
Therefore, it will not warn you of these objects. Ignoring the warnings of the
parking sensor system could cause considerable damage to the vehicle. This
is also valid when using the park assist (e.g. to park behind a truck or motor-
cycle). Therefore, always keep a close watch on the area in front of and behind
the vehicle while parking, and intervene promptly if necessary.
xTo ensure that the system works properly, the bumper sensors must be
kept clean, free of ice and snow and uncovered.
xThe bumper sensors may become damaged or misaligned, for example,
when parking.
WARNING (continued)

Driving231
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xParking perpendicular to the road: Drive next to the gap at a speed of no
more than 20 km/h and at a distance of between 0.5 m and 2 m.
xThe best parking results will be achieved if you position the vehicle as
parallel as possible to the line of parked cars or the kerb.
xWhen a suitable parking place is displayed on the instrument panel, stop
and select reverse gear.
xFollow the instructions given on the instrument panel display
xThen, release the steering wheel when the warning signal sounds Ÿ:
The system will move the steering wheel! Observe the surrounding area.
xObserve the surrounding area and accelerate carefully at a maximum of
up to 7 km/h.
xThe park assist system is only responsible for moving the steering wheel
during the manoeuvre. The driver applies the accelerator, the clutch, the
gears and the brake.
xFollow the instructions given by the park assist system until the
manoeuvre is completed.
xThe park assist system steers the vehicle forwards and backwards until it
is in a straight position in the parking space.
xThe manoeuvre is complete when the corresponding indication is given
on the instrument panel display.
Stopping the parking manoeuvre
The park assist system stops the manoeuvre in the event of one of the
following:
xPress button .
xDriving faster than 7 km/h.
xThe driver moves the steering wheel.
xThe parking manoeuvre has not been completed after six minutes since
the park assist system was activated.
xA sliding door is opened. To restart the manoeuvre, close the sliding door
and press the button again.
xThere is a system malfunction (system temporarily unavailable).
xThe TCS system is switched off or the TCS or ESP is working.
WARNING
The steering wheel turns quickly by itself when parking using the park
assist system. Placing your hand between the steering wheel spokes could
lead to injuries.
Note
The park assist system has its limitations. For example, it is not possible to
park on tight bends using the park assist system.
Note
Even if the park assist system recognises that there is not enough space for
parking the vehicle, the display screen on the instrument panel will still
display this place. In this case, the parking manoeuvre should not be
requested.
Note
Changing gears between forward and reverse gears before indicated (that is,
before the signal from the parking sensor system) the parking results may not
be ideal.
Note
For parallel parking (parallel to the road), a sound will tell the driver when
they must change from forward gears to reverse; the signal from the parking
sensor system does not indicate changes of direction.
i
i

Driving 232
Note
The park assist can also be activated afterwards, if you pass close to a parallel
parking space at a maximum of 40 km an hour or close to be perpendicular
parking space at about 20 km an hour then press the button .
Note
The progress bar on the screen of the instrument panel shows a display of the
relative distance to be covered.
Note
When the Park Assist system is turning the steering wheel of the stopped
vehicle the symbol K is also displayed. Press on the brake pedal so that the
steering can turn with the vehicle at a standstill and thus reduce the number
of manoeuvres.
Note
A suitable parking space length is at least 1.1 m greater than the length of the
vehicle.
Note
If the results of the park assist system are not as good after changing the
wheels, the system must memorise the perimeter of the new wheels. This
process is performed automatically while the vehicle is in motion. To help this
process, turn slowly (at less than 20 km/h), e.g. in an empty car park.
Leaving a parking space using the Park Assist system
Driving off
xSwitch on the engine.
xPress button . When the function is enabled, the button Ÿpage 230,
fig. 152 will light up.
xApply the turn signal indicator for the side on which you want to leave the
parking space.
xSelect reverse gear.
xFollow the instructions given by the park assist system.
xWhen the next indication appears, release the steering wheel Ÿ in
“Parking using the park assist system” on page 230: The system will move
the steering wheel! Observe the surrounding area.
xObserve the surrounding area and accelerate carefully at a maximum of
up to 7 km/h.
xThe park assist system is only responsible for moving the steering wheel
during the manoeuvre. The driver applies the accelerator, the clutch, the
gears and the brake.
xWhen it is possible to leave the parking space, the Park Assist system will
stop. Take control of the steering and when traffic conditions permit, leave
the parking space.
Automatic stoppage of the manoeuvre
The park assist system stops the manoeuvre in the event of one of the
following:
xDriving faster than 7 km/h.
xThe driver moves the steering wheel.
xA sliding door is opened. To restart the manoeuvre, close the sliding door
and press the button again.
xThere is a system malfunction (system temporarily unavailable).
xThe TCS system is switched off or the TCS or ESP is working.
ii
i

Driving233
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
The steering wheel turns quickly automatically when leaving a parking
space using the park assist system. Placing your hand between the
steering wheel spokes could lead to injuries.
Park Assist brake operation
The Park Assist system helps the driver by braking automatically. Automatic
braking does not relieve the driver of responsibility for controlling the accel-
erator, brake and clutch Ÿ.
Braking to avoid damage at excess speed
It is possible that the system operates the brakes to reduce excess speed. The
parking manoeuvre can then continue. The brakes will intervene during each
parking process.
Braking to minimise damage
When approaching an obstacle, the vehicle may brake automatically. In
certain circumstances (for example, storm, detection of ultrasounds, vehicle
status, load, inclination), the Park Assist system may stop the vehicle
completely before an object.
xPress the foot brake Ÿ!
Following the intervention of the brakes, the Park Assist will stop.
WARNING
Despite the assistance provided by the park assist system, do not run any
risks when parking. The system is not a replacement for driver awareness.
xAlways be ready to brake.
xAutomatic brake intervention will end after 1.5 seconds approximately.
Following automatic intervention of the brakes, stop the vehicle yourself.
WARNING (continued)

Driving237
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Parking perpendicular to the road (mode 1)
Summary of the orientation points
Meaning of orientation lines displayed on the screen Ÿfig. 156. All of the
lengths of the orientation lines use a vehicle located on a horizontal surface
as reference.
Red Safety distance: road area located up to around 40 cm behind the
vehicle.
Green: prolongation of the rear of the vehicle (somewhat enlarged). The
area displayed green ends around two metres behind the vehicle, on the
road.
Yellow: prolongation of the rear of the vehicle as the steering wheel
turns. The area displayed yellow ends around three metres behind the
vehicle, on the road.
Parking the vehicle
xStop the vehicle in front of a space and select reverse gear.
xReverse slowly and turn the steering wheel so that the yellow orientation
lines guide you towards the space Ÿfig. 156 .
xAlign the vehicle straight in the parking place using the help of the green
orientation lines.
Parking parallel to the road (mode 2)
After applying the turn signal indicator, the lines and surfaces not required
are deleted.
Summary of the orientation points
Meaning of orientation lines and surfaces displayed on the screen
Ÿfig. 157. All of the lengths of the orientation lines use a vehicle located on
a horizontal surface as reference.
Safety distance: road area located up to around 40 cm behind the
vehicle.
Vehicle side limit.
Fig. 156 Display: orienta-
tion lines for the parking
space behind the vehicle.
A1
A2
A3
A3
Fig. 157 Display: orienta-
tion lines and surfaces for
the space behind the
vehicle.
A1
A2

Driving 238
Turning point when parking. When the yellow line touches the curb or
another limit of the parking space, the point for changing direction
(magnifying glass) will have been reached.
Free space required to park the vehicle parallel. The surface displayed
must completely fit in the space.
Possible vehicle parked next to the curb.
Parking the vehicle
xStop the vehicle 1 m away parallel to the parking space and select reverse
gear.
xSwitch on mode 2 on the navigation system screen for parallel parking.
xSlowly reverse and turn the steering wheel so that the surface displayed
yellow on the screen stops in front of any obstacles (e.g. another vehicle).
xTurn the steering wheel fully towards the space and reverse slowly.
xWhen the yellow line touches the side limit of the space, e.g. the
border or curb (magnifying glass), turn the steering wheel fully in the oppo-
site direction.
xContinue reversing until the vehicle is inside the space, parallel to the
road. Correct the position if necessary.
A3
A4
A5
A5
A3

Driving245
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Tyre monitoring systems
Introduction
The tyre monitor indicator monitors the tyre pressure of each wheel using the
ABS sensors. The ABS sensors monitor the tyre tread perimeter and vibra-
tions of each tire. The tyre monitor indicator warns the driver if it detects a
considerable drop in tyre pressure of one or several tyres while driving. Loss
of tyre pressure will be indicated by the indicator
~ as well as a sound and
sometimes a text message on the screen of the instrument panel. When you
open the driver's door, you will find a label indicating the tyre pressure recom-
mended by the manufacturer for the maximum vehicle load for each tyre
approved for the vehicle in question. By pressing the adjustment button on
the tyre monitoring indicator, you may change the reference pressure for the
tyres so that the tyre pressure to be monitored coincides with actual tyre pres-
sure Ÿpage 248.
Suitable use of the adjustment button Ÿpage 248.
Additional information and warnings:
xTransporting Ÿpage 13
xBraking, stopping and parking Ÿpage 210
xCaring for and cleaning the vehicle exterior Ÿpage 269
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Unsuitable handling of the wheels and tyres may lead to sudden tyre pres-
sure losses, to tread separation or even to a blow-out.
xCheck tyre pressures regularly and ensure they are maintained at the
pressures indicated. If the tyre pressure is too low, the tyres could over-
heat, resulting in tread detachment or even burst tyres.
xTyre pressure should be that indicated on the label when the tyres are
cold at all times Ÿpage 328.
xRegularly check the cold inflation pressure of the tyres. If necessary,
change the tyre pressure of the vehicle tyres while they are cold.
xRegularly check your tyres for damage and wear.
xNever exceed the maximum permitted speed or loads specified for the
type of tyre fitted on your vehicle.
WARNING
Incorrect use of the tyre monitoring indicator button could result in the
indicator giving erroneous messages or prevented from indicating the
danger caused by a defective tyre Ÿpage 248.
Caution
xThe tyre valves may be damaged if the cap is not in place. Check that the
caps are identical to the standard caps and have been correctly tightened. Do
not use metal caps Ÿpage 248.
xDo not damage the valves when changing the tyres Ÿpage 248.
For the sake of the environment
Under-inflated tyres lead to increased fuel consumption and tyre wear.
Note
Do not only rely on the tyre monitoring system. Regularly check your tyres to
ensure that the tyre pressure is correct and that the tyres are not damaged
due to puncture, cuts, tears and impacts/dents. Remove objects from the
tyres only when the tyres have not been pierced by these.
WARNING (continued)

Driving247
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Elements of the tyre monitoring indicatorControl lamp
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
When the tyres are inflated at different pressures or at a pressure that is
too low then a tyre may the damaged resulting in a loss of control of the
vehicle and a serious or mortal accident.
xIf the indicator ~ lights, stop immediately and check the tyres.
xIf the tyres are inflated at different pressures or if a tyre pressure is too
low, this will increase tyre wear, negatively affecting vehicle stability and
increasing braking distances.
Tyre monitoring indicator with button.
See Ÿpage 248.
b Warning lamp ~ on the instrument panel.
b button on the centre console.
b Monitoring the tread of all tyres using ABS sensors (indirect measure-
ment).
b Adjustable medium and full-load tyre pressures.
b Button to update the system when the tyre pressure is changed.
~ SET
Lights
up or
flashes
Possible cause ŸSolution
~
The tyre pressure of a wheel
has dropped considerably in
relation to the pressure set by
the driver Ÿpage 248.
› Stop the vehicle! Reduce your
speed immediately! Stop the
vehicle safely as soon as possi-
ble. Avoid sudden manoeuvres
and braking!
Check all tyres and pressures.
Replace any damaged tyres.
~System malfunction.
Consult a specialist workshop if
the tyre pressure is correct and
the lamp remains lit after switch-
ing the ignition off and back on
again. Have the system checked
there.

Driving 248
xIf tyres are inflated at different pressures or a tyre pressure is too low,
a tyre may be damaged and burst resulting in a loss of control of the
vehicle.
xThe driver is responsible for ensuring that all of the vehicle tyres are
correctly inflated to the right pressure. The recommended tyre pressure is
indicated on the label Ÿpage 328, fig. 183.
xThe tyre monitoring system can only operate correctly if all of the tyres
are inflated to the correct pressure when cold.
xDriving with tyres at the wrong pressure can cause damage to them and
result in an accident. Ensure that the tyre pressures of all the tyres corre-
spond to the vehicle load.
xBefore starting a journey, always inflated tyres to the correct pressure.
xIf tyre pressure is too low then the tyre is subject to greater forces and
it may be heated to such an extent that the tread can rupture and the tyre
will burst.
xWith an overloaded vehicle at high speed, the tyres can overheat and
burst resulting in a loss of vehicle control.
xTyre pressures which are too high or too low reduce the useful life of the
tyre, affecting the vehicle's performance.
xIf a tyre has not been punctured then it does not have to be changed
immediately; drive to the nearest specialist workshop at a moderate speed
and have the tyre checked and inflated to the correct pressure.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Tyre monitoring indicator
The tyre monitor indicator compares wheel revolutions and, with this informa-
tion, the tread of each wheel using the ABS sensors. If the tread of a wheel is
changed, the tyre monitoring indicator will indicate as such on the instrument
panel. The wheel tread changes when:
xTyre pressure is insufficient.
xTyre structure is damaged.
xThe vehicle is unbalanced because of a load.
xThe wheels on an axle are subject to a heavier load (e.g. when towing a
trailer).
WARNING (continued)
Fig. 161 Detailed view of
the centre console: button
for the tyre pressure
monitoring indicator.