lock Seat Alhambra 2013 Owner's Manual

320If and when
Emergency unlocking the rear lid
Fig. 193 From the lug-
gage compartment: Re-
move the rear lid cover
Fig. 194 From the lug-
gage compartment: Man-
ually unlocking the rear
lid
● Remove equipment to access the inside of the rear lid.
● Remove the square cover in the inner trim of the rear lid ⇒ Fig. 193.●
Push the release lever ⇒ Fig. 194 A
in the direction of the arrow to un-
lock the rear lid.
● Manually open the rear lid. 

322If and when
Manually unlocking the gear selector lever
Fig. 197 Remove the lin-
ing from the area of the
gear indication
Fig. 198 Manual release
of gear selector lever
If the vehicle power supply should ever fail (discharged battery, etc.) and
the vehicle has to be pushed or towed, the selector lever must first be
moved to position N using the manual release mechanism. The emergency release mechanism is located underneath the gearbox cover
panel to the right-hand side. To release the gear selector lever mechanism,
a suitable tool is required, for example a screwdriver.
Preparations
●
Apply the parking brake. If the parking brake cannot be activated in the
vehicle must be secured otherwise so that it cannot move.
● Switch the ignition off.
To remove the gearbox cover panel
● Pull the cover up around the dust guard on the gear selector lever
⇒ Fig. 197.
● Take the cover off by passing it over the gear selector lever ⇒ 
.
Manual release of the selector lever
● Press the release lever ⇒ Fig. 198 in the direction of the arrow and hold
it in this position.
● Press the lock button ⇒ Fig. 197 1
on the gear selector lever knob and
place the gear selector lever in the N position.
WARNING
Never move the gear selector lever from the position P while the electron-
ic parking brake is deactivated. Otherwise, the vehicle may accidentally
move off on hills or steep slopes causing serious accidents.
CAUTION
If the vehicle is moved on its wheels with the engine stopped and the selec-
tor lever in position N for a prolonged period of time and at high speed, for
example for towing, then the automatic gearbox will be damaged. 

323
If and when
Vehicle tool kit*
Introduction
When securing the vehicle in case of a breakdown, please note the legal re-
quirements for each country.
Additional information and warnings:
● Working in the engine compartment ⇒ page 278
● Change wheel ⇒ page 309
● In case of emergency ⇒ page 315
WARNING
Loose objects in the vehicle interior can be violently fired through the
compartment in case of a sudden manoeuvre or braking and especially in
accidents causing serious injury.
● Make sure that the vehicle tools are stored safely in the luggage com-
partment.
WARNING
Unsuitable or damaged vehicle tools can cause injury or accidents.
● Never work with inappropriate or damaged tools.
 Location
Fig. 199 In the luggage
compartment, viewed
from inside the vehicle:
The vehicle tool kit loca-
ted in a cavity close to
the lock carrier
Depending on the model, the vehicle tools may be kept in the luggage com-
partment, in a cavity close to the lock carrier ⇒ Fig. 199. Loosen the safety
straps and remove the vehicle tool kit. For vehicles factory-fitted with winter
tyres, you will find additional tools in a toolbox located in the luggage com-
partment.
Note
After use, return the jack to its initial position using the handle in order to
securely store it in the vehicle. 
Safety FirstOperating instructionsPractical tipsTechnical Specifications

335
If and when
To replace the rear lid light bulbs
Fig. 211 On the rear lid:
Remove the cover
Fig. 212 On the rear lid:
Remove the lamp holder Complete operations only in the sequence given:
1.Always take the checklist into account and take the necessary ac-
tions
⇒ page 330.
2.Open the rear lid ⇒ page 83.
3.Extract the cover carefully using the flat part of the screwdriver from
the vehicle tool kit as a lever ( ⇒ Fig. 200) on the indent
⇒ Fig. 211 1
.
4.Release the lamp holder connector by pulling on the red connector
block.
5.Press on the attachment tabs in the direction of the arrow
⇒ Fig. 212 and pull out the lamp holder.
6.Replace the faulty bulb by a new identical bulb.
7.Install the lamp holder. The attachment tabs should audibly click
into place.
8.Insert the cover. The cover should lock into place.
Safety FirstOperating instructionsPractical tipsTechnical Specifications

337
If and when
To change the bulb
9.To release the lamp holder, press on the attachment tabs
⇒ Fig. 214 1 to 4 in the direction of the arrow.10.Remove the lamp holder from the tail light unit.11.Replace the faulty bulb by a new identical bulb.
12.Place the lamp holder in the tail light unit. The attachment tabs
should audibly click into place.
13.Insert the connector and press the red attachment strip in so that
the connector is locked into place.
Assembling the tail light units
Complete operations only in the sequence given:
Tail light, leftTail light, right
14.Carefully insert the tail light unit into the opening in the bodywork.
To do this, insert the upper tail light unit guide into the attachment ring.
15.Tighten the white attachment screw using the screwdriver from thevehicle tool kit.
Tail light, leftTail light, right
16.Ensure that the tail light unit has been correctly fitted and is firmly secured.
17.Replace the cap 1 and rotate it
90° in the opposite direction of
the arrow.Move the 12 V power socket sup-
port upwards gently until it is
correctly closed.
18.Close the storage compartment. 19.Close the rear lid ⇒ page 83.
Safety FirstOperating instructionsPractical tipsTechnical Specifications

338If and when
Changing the number plate light
Fig. 215 On the rear
bumper: number plate
lightsFig. 216 Number plate
light: Remove the lamp
holder
Complete operations only in the sequence given:
Fixed number plate lightBolted number plate light1.Always take the checklist into account and take the necessary actions ⇒ page 330.
2.Press the flat part of the screwdriver included in the vehicle on-board
tools (⇒ Fig. 200) in the direction of the arrow, in the groove of the
number plate light ⇒ Fig. 215.Unscrew the number plate light screws using the screwdriver from the
vehicle tool kit (⇒ Fig. 200).
3.Detach the number plate light.
4.Press on the connector lock in the direction of the arrow ⇒ Fig. 216 Aand pull out the connector.Separate the attachment tabs from the rear panel of the number plate
light by pressing.
5.Rotate the lamp holder in the direction of the arrow B and extract it
with the lamp.Take the lamp holder out of the number plate light.
6.Replace the faulty bulb by a new identical bulb.
7.Insert the lamp holder into the number plate light and rotate all the
way in the opposite direction to the arrow B.Insert the lamp holder into the number plate light.
8.Plug the connector into the lamp holder.Press on the attachment tabs. The lamp holder must be firmly attached
to the number plate light.


342If and when
–Connect one end of the red jump lead to the positive +
termi-
nal of the vehicle with the flat battery A ⇒ Fig. 218.
– Connect the other end of the red jump lead to the positive ter-
minal +
in the vehicle providing assistance B.
– Connect one end of the black jump lead to the negative terminal
–
of the vehicle providing assistance B ⇒ Fig. 218.
– Connect the other end of the black jump lead X
to a solid met-
al component bolted to the engine block or to the engine block
itself of the vehicle with the flat battery. However, connect it to
a point as far as possible from the battery A
.
3. For vehicles with Start-Stop system :
– Connect one end of the red jump lead to the positive +
termi-
nal of the vehicle with the flat battery A ⇒ Fig. 219.
– Connect the other end of the red jump lead to the positive ter-
minal +
in the vehicle providing assistance B.
– Connect one end of the black jump lead X
to a suitable ground
terminal, a solid piece of metal in the engine block, or to the en-
gine block ⇒ Fig. 219.
– Connect the other end of the black jump lead X
to a solid met-
al component bolted to the engine block or to the engine block
itself of the vehicle with the flat battery. However, connect it to
a point as far as possible from the battery A
.
4. Position the leads in such a way that they cannot come into contact with any moving parts in the engine compartment. Starting
5. Start the engine of the vehicle with the boosting battery and let
it run at idling speed.
6. Start the engine of the vehicle with the flat battery and wait two or three minutes until the engine is “running”.
Removing the jump leads
7. Before you remove the jump leads, switch off the dipped beam headlights (if they are switched on).
8. When the engine is running, disconnect the leads in reverse or- der to the details given above.
Connect the battery clamps so they have good metal-to-metal contact with
the battery terminals.
If the engine fails to start, switch off the starter after about 10 seconds and
try again after about half a minute.
WARNING
● Please note the safety warnings referring to working in the engine
compartment ⇒ page 280.
● The battery providing assistance must have the same voltage as the
flat battery (12V) and approximately the same capacity (see imprint on
battery). Failure to comply could result in an explosion.
● Never use jump leads when one of the batteries is frozen. Danger of
explosion! Even after the battery has thawed, battery acid could leak and
cause chemical burns. If a battery freezes, it should be replaced.
● Keep sparks, flames and lit cigarettes away from batteries, danger of
explosion. Failure to comply could result in an explosion. 

343
If and when
WARNING (Continued)
● Observe the instructions provided by the manufacturer of the jump
leads.
● Do not connect the negative cable from the other vehicle directly to
the negative terminal of the flat battery. The gas emitted from the battery
could be ignited by sparks. Danger of explosion.
● Do not attach the negative cable from the other vehicle to parts of the
fuel system or to the brake line.
● The non-insulated parts of the battery clamps must not be allowed to
touch. The jump lead attached to the positive battery terminal must not
touch metal parts of the vehicle, this can cause a short circuit.
● Position the leads in such a way that they cannot come into contact
with any moving parts in the engine compartment.
● Do not lean on the batteries. This could result in chemical burns.
Note
The vehicles must not touch each other, otherwise electricity could flow as
soon as the positive terminals are connected. 
Towing and tow starting Introduction
When towing, always respect legal requirements.
For technical reasons, it is not possible to tow a vehicle if the battery is flat.
Additional information and warnings:
● Electronic power control and exhaust gases purification system
⇒  page 231
WARNING
A vehicle with a flat battery should never be towed.
● Never remove the key from the ignition lock. The electronic steering
lock could engage. Then the vehicle will be uncontrollable. You may lose
control of the vehicle and there is a risk of serious accident.
WARNING
When towing the vehicle, the handling and braking efficiency change
considerably. Please observe the following instructions to minimise the
risk of serious accidents and injury:
● As the driver of the vehicle being towed:
– The brake must be depressed must harder as the brake servo does
not operate. Always remain aware to avoid collision with the towing
vehicle.
– More strength is required at the steering wheel as the power steer-
ing does not operate when the engine is switched off.
● As the driver of the towing vehicle:
– Accelerate gently and carefully.
– Avoid sudden braking and manoeuvres.
– Brake well in advance than usual and brake gently.
CAUTION
● Carefully fit and remove the towline anchorage and its cover to avoid
damage to the vehicle (for example, paintwork).
● When towing, fuel could enter the catalytic converter and cause dam-
age! 
Safety FirstOperating instructionsPractical tipsTechnical Specifications

344If and when
Instructions for tow starting
In general, the vehicle should not be started by towing. Jump-starting is
much more preferable ⇒  page 340.
For technical reasons, the following vehicles can not be tow started:
● Vehicles with an automatic gearbox.
● Vehicles with an electronic parking brake, given that it is possible that
the brake will not be disengaged.
● If the vehicle battery is flat, it is possible that the engine control units do
not operate correctly.
However, if your vehicle must absolutely be tow-started (manual gearbox):
● Engage the 2nd or 3rd gear.
● Keep the clutch pressed down.
● Switch on the ignition and the hazard warning lights.
● Release the clutch when both vehicles are moving.
● As soon as the engine starts, press the clutch and move the gear lever
into neutral. This helps to prevent a collision with the towing vehicle.
CAUTION
When tow-starting, fuel could enter the catalytic converter and damage it. 
Towing instructions
Tow rope or tow bar
When towing, the tow bar is the safest and vehicle friendly way. You should
only use a tow rope if you do not have a tow bar. A tow rope should be slightly elastic to avoid damage to both vehicles. It is
advisable to use a tow rope made of synthetic fibre or similarly elastic mate-
rial.
Only secure the tow rope or tow bar to the towline anchorage or specially
designed fitting.
Vehicles with a
factory fitted towing device , can only be used for towing
with a tow bar, specially designed to fit on a tow hitch ball ⇒ page 236.
Towing vehicles with an automatic gearbox
Note the following for a towed vehicle:
● Make sure the gear selector lever is in the N position.
● Do not drive faster than 50 km/h (30 mph) when towing a vehicle.
● Do not tow further than 50 km (30 miles).
● If a breakdown truck is used, the vehicle must be towed with the front
wheels raised. Note the following instructions for towing four all-wheel drive
vehicles.
Instructions for towing all-wheel drive vehicles
All-wheel drive vehicles can be towed using a toolbar or tow rope. If the ve-
hicle is towed with the front or rear axle raised, the engine must be turned
off to avoid transmission damage.
For vehicles with a double clutched DSG ®
(direct shift gearbox) the instruc-
tions for towing vehicles with an automatic gearbox apply ⇒ page 344.
Situations in which the vehicle should not be towed
In the following cases, the vehicle should not be towed but transported on a
trailer or special vehicle:
● If the vehicle gearbox does not contain lubricant due to a fault.
● If the vehicle battery is flat and, as a result, the electronic steering lock
and electronic parking brake cannot be disengaged if applied.
● If the vehicle to be towed has an automatic gearbox and the distance to
be covered is greater than 50 km (30 miles). 

345
If and when
Note
The vehicle can only be towed if the electronic parking brake and steering
lock are deactivated. If the vehicle has no power supply or there is an elec-
tric system fault, the engine must be started using jump leads to deactivate
the electronic parking brake and electronic steering lock. 
Fitting the front towline anchorage
Fig. 220 On the right-
hand side of the front
bumper: Screw in the
towline anchorage
The location for the removable towline anchorage is on the right-hand side
of the front bumper ⇒ Fig. 220.
The towline anchorage should always be kept in the vehicle.
Note the instructions for towing ⇒ page 344.
To fit the towline anchorage
● Take the towline anchorage from the vehicle tool kit
⇒ page 323.
● Press on the upper cover and carefully remove it forwards. Allow the cov-
er to hang. ●
Screw in the towline anchorage into its position anticlockwise as far as
it will go ⇒ Fig. 220 ⇒ 
. Use a suitable tool to firmly tighten the towline
anchorage in its location.
● After towing, remove the towline anchorage by turning it clockwise and
put the cover back in place.
CAUTION
The towline anchorage must always be completely and firmly tightened.
Otherwise, it could be released while towing and tow-starting. 
Fitting the rear towline anchorage
Fig. 221 On the rear
bumper, to the right hand
side: Tow ring in position
The location for the removable towline anchorage is on the right-hand side
of the rear bumper ⇒ Fig. 221. For vehicles with a factory fitted towing brack-
et, there is no fitting behind the cover to insert the towline anchorage. For
towing, fit and use the tow hitch ⇒ page 236, ⇒ 
.
Note the instructions for towing ⇒ page 344. 
Safety FirstOperating instructionsPractical tipsTechnical Specifications