warning Seat Altea 2007 Owner's Guide
[x] Cancel search | Manufacturer: SEAT, Model Year: 2007, Model line: Altea, Model: Seat Altea 2007Pages: 302, PDF Size: 9.17 MB
Page 30 of 302

Seat belts
28
– Press the upper part of the shoulder belt guide and hold it in this position  ⇒page 27, fig. 17.
– Move the shoulder belt guide up or down until you have adjusted  the seat belt  ⇒page 25.
– After adjusting, pull the shoulder belt sharply to check that the  catch on the shoulder belt guide is engaged securely.Incorrectly fastened seat belts
Incorrectly worn seat belts can cause severe injuries.Seat belts can provide optimal protection only if the belt web is 
properly worn. The seat belts must be fastened exactly in the order 
described in this chapter. An incorrect sitting position impairs 
substantially the protection a seat belt offers and can lead to severe 
or fatal injuries. The risk of severe or fatal injuries is especially 
increased when a deploying airbag strikes an occupant who has 
assumed an incorrect sitting position . As driver, you are responsible 
for all vehicle occupants, especially children. Therefore:
– Never permit anyone to assume an incorrect sitting position in  the vehicle while travelling  ⇒.
WARNING
•
An incorrectly worn seat belt incr eases the risk of severe injuries.
•
Before every trip, instruct your passengers to adjust their seat belts 
properly and to wear them during the trip.
•
Read and always observe information and warnings concerning the use 
of seat belts ⇒ page 23.
Belt tension devicesFunction of the belt tension device
During a frontal collision, the se at belts on the front seats are 
retracted automatically.The seat belts for the front occupants are equipped with belt tension devices. 
Sensors will trigger the belt tension devices during severe head-on, lateral 
and rear collisions only if the seat  belt is being worn. This retracts and 
tightens the seat belts, reducing the forward motion of the occupants.
The belt tension device ca n be triggered only once.
The belt tension devices will not be triggered in the event of a light frontal, 
side or rear collision, if the vehicle overturns, or in situations where no large 
forces act on the front, side or rear of the vehicle.
Note
•
If the belt tension devices are triggered, a fine dust is produced. This is 
normal and is no indication that there was a fire in the vehicle.
•
The relevant safety requirements must be observed when the vehicle or 
components of the system are scrapped. A qualified workshop is familiar with 
these regulations and will be pleased to pass on the information to you.
Service and disposal of belt tension devicesThe belt tension devices are components of the seat belts that are installed 
in the seats of your vehicle. If you work on the belt tension devices or remove 
and install parts of the system when performing other repair work, the seat 
belt may be damaged. The consequence may be that, in the event of an acci-
dent, the belt tension  devices function incorrectly or not at all.
altea_ingles_0706.book  Seite 28  Mittwoch, 30. August 2006  3:48 15 
Page 31 of 302

Seat belts29
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
So that the effectiveness of the belt tension device is not reduced and that 
removed parts do not cause 
any injuries or environmental pollution, regula-
tions, which are known to the qualifi ed workshops, must be observed.
WARNING
•
If repairs are not carried out by a professional, or if the belt tension 
devices are used incorrectly, the risk of severe or fatal injuries increases. 
The belt tension devices may fail to trigger or may trigger in the wrong 
circumstances.
•
Never attempt to repair, adjust, remove or install parts of the belt 
tension devices or seat belts.
•
The belt tension device and seat be lt including its automatic retractor 
cannot be repaired.
•
Any work on the belt tension devi ces and seat belts, including the 
removal and refitting of system parts in conjunction with other repair work, 
must be performed by a qualified workshop only.
•
The belt tension devices will only provide protection for one accident 
and must be c hanged if they have been activated.
altea_ingles_0706.book  Seite 29  Mittwoch, 30. August 2006  3:48 15 
Page 32 of 302

Airbag system
30Airbag systemBrief introductionWhy wear a seat belt and assume the correct sitting position?
For the inflating airbags to achieve the best protection, the 
sea t b el t  m u st  al w ay s  b e  w o rn  p ro p e rly  a nd  t h e  co rrec t  s i tt i n g  
position must be assumed.For your own safety and the safety  of the passengers, please ensure 
the following before you drive:
– Always wear the seat belt properly  ⇒page 19.
– Adjust the driver seat and the steering wheel correctly  ⇒page 10.
– Adjust the front passenger seat correctly  ⇒page 11.
– Adjust the head restraint seat correctly  ⇒page 13.
– Use the correct child restraint system to protect children in your  vehicle  ⇒page 46.The airbag deploys in fractions of a second and with a high velocity. If you 
have assumed an incorrect seating po sition at that moment, you could 
sustain critical injuries. Therefore, it  is essential that all occupants maintain 
a correct sitting position while travelling.
Braking heavily the moment before an accident may cause an occupant not 
wearing a seat belt to be thrown forwar d into the area of the deploying airbag.  In this case, the inflating airbag may infl
ict critical or fatal injuries upon the 
occupant. This applies particularly to children.
Always maintain the greatest possible distance between yourself and the 
front airbag. This way, the front airbags can completely deploy when trig-
gered, providing their maximum protection.
The most important factors for triggering the airbag are the type of accident, 
the angle of impact and the vehicle speed.
Whether the airbags are triggered depends primarily on the vehicle deceler-
ation rate resulting from the collision an d detected by the control unit. If the 
vehicle deceleration occurring duri ng the collision and measured by the 
control unit remains below the specifie d reference values, the front, side 
and/or curtain airbag will not be triggered. Take into account that the visible 
damage  in a vehicle following an accident, for whatever reason, is not an 
indication as to why the airbags were triggered.
WARNING
•
Wearing the seat belt incorrectly or assuming an incorrect sitting posi-
tion can lead to critical or fatal injuries.
•
All occupants, including children, who are not properly belted can 
sustain critical or fatal injuries if the airbag is triggered. You should always 
transport all children up to 12 years of age on the rear seat. Never transport 
children in the vehicle if they are not restrained or the restraint system is 
not appropriate for their age, size or weight.
•
If you are not wearing a seat belt or  if you lean forward or to the side or 
assume an incorrect sitting position, the risk of injury is increased 
substantially. This increased risk of injury will be further increased if you 
are struck by an inflating airbag.
•
To reduce the risk of injury from an inflating airbag, always wear the 
seat belt properly ⇒ page 19.
altea_ingles_0706.book  Seite 30  Mittwoch, 30. August 2006  3:48 15 
Page 33 of 302

Airbag system31
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
•
Always properly adjust the front seats.
The danger of fitting a child seat on the front passenger seat
Rear-facing child seats must never be used on the front 
passenger seat when the front  passenger airbag is enabled.An enabled front airbag on the front passenger side is potentially a major 
danger to a child. The front passenger seat is life threatening to a child if you 
transport the child in a rear-facing child seat. You should always transport all 
children up to 12 years of age on the rear seat.
If a rear-facing child seat is secured to the front passenger seat, an inflating 
airbag can strike it with such great force that critical or fatal injuries may 
result.
Therefore we urgently recommend that you transport children on the rear 
seats. That is the safest place in the vehicle for children. Alternatively, the 
front passenger airbag can be disabled with a key-operated switch 
⇒page 44. When transporting children, use a child seat appropriate to the 
age and size of each child ⇒ page 46.
For those vehicles that do not include a key lock switch to turn the airbag off, 
an Authorised Service Centre must be consulted.
WARNING
•
If a child seat is secured to the front passenger seat, the risk to the child 
of sustaining critical or fatal injuries in the event of an accident increases.
•
Never secure a rear-facing child seat to the front passenger seat if the 
front passenger airbag is enabled. The child can suffer critical or fatal inju-
ries when the front passenger airbag is triggered.
•
An inflating front passenger airbag can strike the rear-facing child seat 
and hurl it with great force against the door, the roof or the backrest.
•
If, under special circumstances, it should be necessary to transport a 
child in a rear-facing child seat on the front passenger seat, it is absolutely 
essential that you observe the following safety measures:
−Disable the front passenger airbag  ⇒page 44, “Deactivating 
airbags*”.
− The child seat must be approved by the child seat manufacturer for 
use on a front passenger seat with front or side airbag.
− Follow the installation instructio ns of the child seat manufacturer 
and absolutely observe the warnings  ⇒page 46, “Child safety”.
− Before properly installing the child seat, push the front passenger 
seat all the way to the rear so that  the greatest possible distance to the 
front passenger airbag is ensured.
− Ensure that no objects prevent the front passenger seat from being 
pushed completely back.
− The backrest of the front passenger seat must be in an upright 
position.
Warning lamp for airbag and belt tension device system 
This warning lamp monitors the airbag and belt tension 
device system.The warning lamp monitors all airbags and belt tension devices in the 
vehicle, including control units and wiring connections.
WARNING (continued)
WARNING (continued)
altea_ingles_0706.book  Seite 31  Mittwoch, 30. August 2006  3:48 15 
Page 34 of 302

Airbag system
32Monitoring of airbag and belt tension device system
The functionality of the airbag and belt tension device system is constantly 
monitored electronically. Each time th e ignition is switched on, the warning 
lamp 
 lights for several seconds and the display in the instrument panel* 
shows  AIRBAG / TENSIONER .
The system must be checked when the warning lamp 
 :
•
does not come on when the ignition is switched on,
•
does not go out about 4 seconds after the ignition is switched on,
•
goes out and then comes on again after the ignition is switched on,
•
or if it comes on or flickers while the car is moving.
In the event of a malfunction, the warning lamp remains on continuously. In 
addition, depending on the malfunctio n, a fault message appears in the 
display of the combi-instrument for approx. 10 seconds and a short acoustic 
signal is given. In this event, you should have a qualified workshop check the 
system immediately.
If any of the airbags are deactivated by the Authorised Service Centre, the 
indicator lights for several  seconds more after the veri fication and will turn off 
if there is no fault.
WARNING
•
If there is a malfunction, the air bag and belt tension device system 
cannot properly perform its protective function.
•
If a malfunction should occur, have the system checked immediately by 
a qualified workshop. Otherwise there is a risk that, in the event of an acci-
dent, the airbag system and belt tension devices may not be triggered, or 
may not be triggered correctly.
Repair, care and disposal of the airbagsThe parts of the airbag system are installed in various places in your vehicle. 
If you work on the airbag system or remove and install parts of the system 
when performing other repair work, parts of the airbag system may be 
damaged. The consequence may be that, in the event of an accident, the 
airbag inflates incorrectly  or does not inflate at all.
The relevant safety requirements must be observed when the vehicle or 
components of the airbag are scrapped . The specialist workshops and the 
Vehicle disposal centres are familiar with these requirements.
WARNING
•
If repairs are not carried out by a professional, or if the airbags are used 
incorrectly, the risk of severe or fatal injuries is increased. The airbags may 
fail to inflate, or could inflate in the wrong circumstances.
•
Do not cover or stick anything on  the steering wheel hub or the soft 
plastic surface of the airbag unit on the passenger side of the dashboard, 
and do not obstruct or modify them in any way.
•
It is important not to attach any objects such as cup holders or tele-
phone mountings to the surfaces covering the airbag units.
•
To clean the steering wheel or dash panel, you may use only a dry cloth 
or one moistened with water. Never clean the dash panel and surface of the 
airbag module with cleansers containing solvents. Solvents cause the 
surface to become porous. If the airbag inflates, disintegrating plastic 
parts can cause substantial injuries.
•
Never attempt to repair, adjust, remove or install parts of the airbag 
system.
•
Any work on the airbag system or re moval and installation of the airbag 
components for other repairs (such as repairs to the steering wheel) should 
be performed only by a qualified workshop. Qualified workshops have the 
necessary tools, repair information and qualified personnel.
altea_ingles_0706.book  Seite 32  Mittwoch, 30. August 2006  3:48 15 
Page 35 of 302

Airbag system33
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
•
We urgently recommend that you go to a qualified workshop for all 
work on the airbag system.
•
Never attempt to alter the front bumper or the body.
•
The airbags provide protection for one accident only, if they have been 
deployed they must be replaced.WARNING (continued)
altea_ingles_0706.book  Seite 33  Mittwoch, 30. August 2006  3:48 15 
Page 36 of 302

Airbag system
34Front airbagsDescription of front airbags
The airbag system is not a substitute for the seat belts.
The front airbag for the driver is located in the steering wheel  ⇒fig. 18  and 
the airbag for the front passenger is located in the dash panel  ⇒fig. 19. 
Airbags are identified by the text “AIRBAG”.
In conjunction with the seat belts,  the front airbag system gives the front 
occupants additional protection for the head and chest in the event of a 
severe frontal collision  ⇒page 37, “Safety notes on front airbag system”.
In addition to their normal function  of restraining the occupants, the seat 
belts also hold the driver  and front passenger in a position where the airbags 
can provide maximum protection in a frontal collision.
The airbag system is not a substitute for  seat belts, but is an integral part of 
the vehicle's overall passive safety system. Please bear in mind that the 
airbag system can only work effectively when the occupants are wearing their 
seat belts correctly and have adjusted the head restraints properly. For this 
reason, it is most important to wear the seat belts at all times - not only 
because this is required by law in most  countries, but also for your safety 
⇒ page 19, “Introduction”.
The main parts of the front airbag system are:•
an electronic control and monitoring system (control unit),
•
the two front airbags (airbag with gas generator) for the driver and front 
passenger,
•
a warning lamp 
 in the dash panel insert ⇒ page 31.
The functionality of the airbag system is monitored electronically. The airbag 
warning lamp will light up for a few  seconds every time the ignition is 
switched on (self-diagnosis).
There is a fault in the system if the warning lamp 
•
does not come on when the ignition is switched on  ⇒page 31,
•
does not go out about 4 seconds af ter the ignition is switched on,
•
goes out and then comes on again after the ignition is switched on,
•
or if it comes on or flickers while the car is moving.
Fig. 18  Driver airbag 
located in steering wheelFig. 19  Front passenger 
airbag located in dash 
panel
altea_ingles_0706.book  Seite 34  Mittwoch, 30. August 2006  3:48 15 
Page 37 of 302

Airbag system35
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
The front airbag system will not be triggered if:
•
if the ignition is switched off,
•
during a minor frontal collision,
•
during a minor side collision,
•
during a rear-end collision,
•
or if the vehicle rolls.
WARNING
•
The seat belts and airbags can only provide maximum protection if the 
occupants are seated correctly  ⇒page 10, “Proper sitting position for 
occupants”.
•
If a fault should occur in the airbag system, have the system checked 
immediately by a qualified workshop. Otherwise there is a danger that 
during a frontal collision, the system may fail to trigger, or not trigger 
correctly.
Function of front airbags
Inflated airbags reduce the risk of head or chest injury.The airbag system is designed so that the airbags for the driver and front 
passenger are triggered in a severe frontal collision.
In certain types of accident the front, curtain and side airbags may be trig-
gered together.
When the system is triggered, the airbags fill with a propellant gas and 
deploy in front of the driver and front passenger  ⇒fig. 20 . The fully deployed 
airbags cushion the forward movement of the front occupants and help to 
reduce the risk of injury to the head and the upper part of the body.
The special design of the airbag allows the controlled escape of the propel-
lant gas when an occupant puts pressure on the bag. Thus, the head and 
chest are surrounded and protected by the airbag. Once the impact has been 
absorbed, the airbag deflates sufficiently for the front occupants to see 
forward.
Fig. 20  Inflated front 
airbags
altea_ingles_0706.book  Seite 35  Mittwoch, 30. August 2006  3:48 15 
Page 39 of 302

Airbag system37
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
Safety notes on front airbag system
If you use airbags correctly, they can considerably reduce the 
risk of injury in many kinds of accident.
WARNING
•
It is important for the driver and front passenger to maintain a distance 
of at least 25 cm from the steering wheel or dash panel. If the minimum 
distance is not observed then the airbags do not correctly protect the 
vehicle occupants; risk of fatal injuries! In addition, the front seats and 
head restraints must always be positioned correctly for the height of the 
occupant.
•
If you are not wearing a seat belt or if you lean forward or to the side or 
assume an incorrect sitting position, the risk of injury is increased 
substantially. This increased risk of injury will be further increased if you 
are struck by an inflating airbag.
•
Never let a child travel on the front seat without an appropriate restraint 
system. If the airbag is triggered in an accident, children can sustain 
serious or fatal injuries from the airbag as it inflates  ⇒page 46, “Child 
safety”.
•
Occupants sitting in the front of the vehicle must never carry any 
objects or pets in the deployment sp ace between them and the airbags, or 
allow children or other passengers to travel in this position.
•
The airbags provide protection for one accident only, if they have been 
deployed they must be replaced.
•
It is also important not to attach any objects such as cup holders or 
telephone mountings to the surfaces covering the airbag units.
•
Do not attempt to modify components of the airbag system in any 
way.
Side airbags*Description of side airbags
The airbag system is not a substitute for the seat belts.The front side airbags are located in th e padding of the driver's seat back and 
front passenger seat back  ⇒fig. 22. The rear side air bags are located in the 
lining of the rear wheel housing. The locations are identified by the text 
“AIRBAG” in the upper region of the ba ckrests and rear wheel housing lining.
In conjunction with the seat belts, the side airbag system gives the front seat 
occupants additional protection for the upper body in the event of a severe 
side collision  ⇒page 40, “Safety notes on the operation of the side airbag 
system”.
In a side collision, the side airbags reduce the risk of injury to passengers on 
the front seats to the areas of the body facing the impact. In addition to their 
normal function of protecting the occupan ts in a collision, the seat belts also 
Fig. 22  Side airbag in 
driver seat
altea_ingles_0706.book  Seite 37  Mittwoch, 30. August 2006  3:48 15 
Page 40 of 302

Airbag system
38hold the passengers on the front seats and the outer rear seats in a position 
where the side airbags can provide maximum protection.
The airbag system is not a substitute for seat belts, but is an integral part of 
the vehicle's overall passive safety system. Please bear in mind that the 
airbag system can only work effectively when the occupants are wearing their 
seat belts. For this reason, it is most important to wear the seat belts at all 
times - not only because this  is required by law in most countries, but also for 
your safety  ⇒page 19, “Introduction”.
The side airbag system will not be triggered•
if the ignition is switched off,
•
during a minor side collision,
•
during a minor frontal collision,
•
during a rear-end collision,
•
or if the vehicle rolls.
The main parts of the airbag system are
•
an electronic control and monitoring system (control unit),
•
the side airbags in the front seat backs and the rear side airbags in the 
rear wheel housing lining,
•
a warning lamp 
 in the dash panel insert  ⇒page 31.
The functionality of the airbag system is monitored electronically. The airbag 
warning lamp will light up for approx.  4 seconds every time the ignition is 
switched on (self-diagnosis).
WARNING
•
In a side-on collision, the side airb ags will not work, if the sensors do 
not correctly measure the pressure increase on the interior of the doors, 
due to air escaping through the areas with holes or openings in the door 
panel.
•
Never drive the vehicle if the interior panels have been removed.
•
Never drive if the interior door panels have been removed or if the 
panels have not been correctly fitted.
•
Never drive the vehicle if the loudspeakers in the door panels have 
been removed, unless the holes left by the loudspeakers have been 
correctly closed.
•
Always check that the openings are closed or covered if loudspeakers 
or other equipment are fitted in the interior door panels.
•
Any work carried out to the doors sh ould be made in a qualified author-
ised workshop.
•
The seat belts and airbags can only  provide maximum protection if the 
occupants are seated correctly  ⇒page 10, “Proper sitting position for 
occupants”.
•
If a fault should occur in the airbag system, have the system checked 
immediately by a qualified workshop.  Otherwise there is a danger that 
during a side collision, the system may fail to trigger, or not trigger 
correctly.WARNING (continued)
altea_ingles_0706.book  Seite 38  Mittwoch, 30. August 2006  3:48 15