turn signal Seat Exeo ST 2010 Owner's Guide

If and when
270Changing the turn signal bulb
The procedure for changing the bulb is the same on both
sides.– Switch off the ignition and the lights.
– Raise the bonnet.
– Turn the bulb holder anti-clockwise, pulling it by the grip
⇒fig. 205 and removing the bulb holder and the bulb.
– Replace the blown bulb in the bulb holder (press and turn anti- clockwise to remove) with a new bulb (press and turn clockwise
to insert).
– Installation is done in the reverse order.
– Check whether the new bulb is working. Note
Although it is not necessary, previously remove the rigid cover
⇒page 272,
fig. 208 for easier turn signal bulb changes.
Fig. 205 Turn signal
ExeoST_EN.book Seite 270 Freitag, 3. September 2010 11:41 11

If and when275
Safety First
Operating Instructions
Practical Tips
Technical Specifications
WARNING
•Take particular care when working on components in the engine
compartment if the engine is warm - risk of burns!•Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.•The high voltage element of gas discharge bulbs* (xenon light) must be
handled correctly. Otherwise, there is a risk of death.•When changing bulbs, please take care not to injure yourself on sharp
parts in the headlight housing.Caution
•Remove the ignition key before working on the electric system. If not, a
short circuit could occur.•Switch off the lights or parking lights before you change a bulb.For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in the proper
manner.
Note
•Depending on weather conditions (cold or wet), the front lights, the fog
lights, the tail lights and the turn signals may be temporarily misted. This has no influence on the useful life of the lighting system. By switching on the
lights, the area through which the beam of light is projected will quickly be
demisted. However, the edges may continue to be misted.
•Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning pr operly. This is not only in the interest
of your own safety, but also in that of all other road users.•Before changing a bulb, make sure you have the correct new bulb.•Do not touch the glass part of the bulb with your bare hands, use a cloth
or paper towel instead. Otherwise, the fingerprints left on the glass will
vaporise as a result of the heat generated by the bulb, be deposited on the
reflector and impair its surface.Removing the air duct
The air duct has to be removed to gain access to the bulbs for
the right-side headlight.
Bulb
Type
Xenon bulbs
12 V/35 W (D1S)
DRL (day light)
12 V/21 W (P21W SLL)
Turn signal
12 V/21 W (PY21W)
Side lights
12 V/5 W (W5W blue LL)
Fig. 214 Air duct on right
side of vehicle
ExeoST_EN.book Seite 275 Freitag, 3. September 2010 11:41 11

If and when
276
–Unscrew bolts ⇒page 275, fig. 214 .
– Detach air duct from guide and take it out.Fitting the air duct
Once the bulb(s) for the right-side headlight have been
changed, the air duct must be re-installed.– Place the air duct in the correct position.
– First turn the two screws in lightly, then tighten both screws.
– Push the air duct into guide .
Bi-Xenon AFS headlight bulbs
Turn signal
Xenon headlight (dipped beam/main beam)
Side lights
DRL light
AA
AB
Fig. 215 Air duct on right
side of vehicle
AAAB
Fig. 216 Bi-Xenon AFS
headlight bulbs
AAABACAD
ExeoST_EN.book Seite 276 Freitag, 3. September 2010 11:41 11

If and when
278Changing the turn signal bulb
The procedure for changing the bulb is the same on both
sides.
– Switch off the ignition and the lights.
– Raise the bonnet.
– Pull the rubber cap ⇒ fig. 218 to remove it.
– Remove the bulb holder by pulling on the grip and turning it anti- clockwise ⇒fig. 219 .
– Replace the blown bulb in the bulb holder (press and turn anti- clockwise to remove) with a new bulb (press and turn clockwise
to insert).
– Insert the bulb holder into the socket with the tab facing upwards and the grip horizontal. Press it against the socket and turn
clockwise. When changing the bulb, you can check the position
of the bulb through the headlight glass.
– Fit the rubber cap and tighten, making sure it fit properly into the headlight casing.
– Check whether the new bulb is working.
Fig. 218 Turn signalFig. 219 Turn signal
ExeoST_EN.book Seite 278 Freitag, 3. September 2010 11:41 11

If and when
280Changing tail light bulbs (on side panel)Overview of tail lightsTail lights on side panel•Brake lights and side lights•Turn signal
Overview of tail lights. LED lampsTail lights on side panel•Brake lights and side lights•Turn signalNote
•It is only possible to change the turn signal light.•If the warning lamp for the brake light or side light (LED lamp) lights up,
the tail light assembly should be replaced.•The failure of the lamp is only shown when the LED function goes out
completely. Sometimes, a LED will stop working, without displaying the
warning as the function continues to operate.
Fig. 222 Overview of tail
lights
Fig. 223 Overview of tail
lights
ExeoST_EN.book Seite 280 Freitag, 3. September 2010 11:41 11

If and when283
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Position of the bulbs
Changing bulbs. LED lamps
All bulbs can be changed easily in the bulb holder.The bulb is secured with a bayonet fastening. The table below gives
an overview of the bulb positions.
– Lightly press the defective bulb into the bulb holder, then turn it
to the left and remove it. – Fit the new bulb, pressing it into the bulb holder and turn it to the
right as far as it will go.
– Use a cloth to remove any fingerp rints from the glass part of the
bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒page 283.
Position of the bulbsFitting the bulb holder
The bulb holder is easy to fit.
Pos. ⇒ page 282,
fig. 227
Bulb function
A
Turn signal
B
Brake lights and side lights
Fig. 228 Position of the
bulbs in the bulb holder:
Example: Outer left tail
light
Pos. ⇒ fig. 228
Bulb function
A
Turn signal
Fig. 229 Securing the
bulb holder in the tail
light unit
ExeoST_EN.book Seite 283 Freitag, 3. September 2010 11:41 11

If and when
288
– Fit the new bulb, pressing it into the bulb holder and turn it to the right as far as it will go.
– Use a cloth to remove any fingerp rints from the glass part of the
bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒ page 288.Position of the bulbsFitting the bulb holder
The bulb holder is easy to fit.– Position the bulb holder on the tail light and align it so that it is
securely seated.
– Press the bulb holder into the tail light until it engages.
– Fit the cover back in the interior trim so that it engages.
– Put the screwdriver back into the tool kit.
– Make sure that all bulbs for the tail lights are working.
Side turn signals– Press the turn signal to the left or to the right to remove the bulb.
– Remove the bulb holder from the turn signal.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the bulb holder in the turn signal guide until it clicks into place.
– First place the turn signal in th e opening in the bodywork, fixing
the tabs ⇒ fig. 238, arrow .
– Insert the bulb as shown by the arrow ⇒fig. 238.
Pos. ⇒ page 287,
fig. 236
Bulb function
A
Reverse lights
B
Rear fog light
Fig. 238 Side turn signal
A1
A2
ExeoST_EN.book Seite 288 Freitag, 3. September 2010 11:41 11

If and when295
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Do not pull too hard with the towing vehicle and take care to avoid jerking the
tow-rope. When towing on an unpaved road, there is always a risk of over-
loading and damaging the anchorage points.
The ignition of the vehicle being towed must be switched on to prevent the
steering wheel from locking and also to allow the use of the turn signals,
horn, windscreen wipers and washers.
As the brake servo does not work if the engine is not running, you must apply
considerably more pressure to the brake pedal than you normally would.
As the power assisted steering does not work if the engine is not running, you
will need more strength to steer than you normally would.
Towing vehicles with an automatic gearbox
•Put the selector lever into position “N”.•Do not drive faster than 50 km/h when towing a vehicle.•Do not tow further than 50 km.•If a breakdown vehicle is used, the vehicle must be towed with the front
wheels raised.Note
•Observe legal requirements when towing or tow-starting.•Switch on the hazard warning lights of both vehicles. However, observe
any regulations to the contrary.•For technical reasons, vehicles with an automatic gearbox must not be
tow-started.•If damage to your vehicle means that there is no lubricant in the gearbox,
you must raise the drive wheels while the vehicle is being towed.•If the vehicle has to be towed more than 50 km, the front wheels should
be raised during towing, and towing should be carried out by a qualified
person.
•The steering wheel is locked when the vehicle has no electrical power. The
vehicle must then be towed with the front wheels raised. Towing should be
carried out by a qualified person.•The towing eye should always be kept in the vehicle. Please refer to the
notes ⇒page 294, “Tow-starting”.Front towing eyeFitting the towing eye
– Take the towing ring from the on-board tool set.
– Remove the front cover by pressing down on the right hand side.
– Bolt the eye to its limit to the left, in the direction of the arrow
⇒ fig. 246 .
Fig. 246 Fitting the
towing eye to front rear of
the vehicle
ExeoST_EN.book Seite 295 Freitag, 3. September 2010 11:41 11

Index
320Sliding/tilting sunroof . . . . . . . . . . . . . . . . . . . 112
Automatic close function . . . . . . . . . . . . . . 113
Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Emergency activation . . . . . . . . . . . . . . . . . 114
Manual operation . . . . . . . . . . . . . . . . . . . . 114
Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Snow chains . . . . . . . . . . . . . . . . . . . . . . . 253, 300
Solar sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Solar-powered blower/sunroof . . . . . . . . . . . . 171
Spare keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Spare wheel Steel rim . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Speed warning . . . . . . . . . . . . . . . . . . . . . . . 81, 82
Speed warning function . . . . . . . . . . . . . . . . . . . 82
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Steam jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Steering Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Manual steering wheel adjustment . . . . . . 172
Steering wheel controls . . . . . . . . . . . . . . . . . . . 91
Stopping the engine . . . . . . . . . . . . . . . . . . . . . 175
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Switches in the driver door Electric windows . . . . . . . . . . . . . . . . . . . . . 110
Symbols Red symbols in central display . . . . . . . . . . 77
Yellow symbols in central display . . . . . . . . 79
TTailgateCentral locking system . . . . . . . . . . . . . . . . 103
Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
TCS How the system works . . . . . . . . . . . . . . . . 194
Technical modifications . . . . . . . . . . . . . . . . . . 223
The danger of not using the seat belt . . . . . . . . 20
The environment Heated rear window . . . . . . . . . . . . . . . . . . 127
Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Warming up the engine . . . . . . . . . . . . . . . 174
Tightening torque of wheel bolts . . . . . . . . . . . 300
tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 189
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Tow starting General notes . . . . . . . . . . . . . . . . . . . . . . . 294
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203, 294 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 205
Notes on towing . . . . . . . . . . . . . . . . . 203, 204
Removable towing bracket . . . . . . . . . . . . . 206
Technical requirements . . . . . . . . . . . . . . . 203
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . 299
Towing bracket, fitting . . . . . . . . . . . . . . . . . . . 212
Towing eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
Towing eyes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Tow-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
Traction control system How the system works . . . . . . . . . . . . . . . . 194
Trailer weights . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Trip recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Turn signal lamps
Hazard warning lights . . . . . . . . . . . . . . . . . . 68
Trailer turn signals . . . . . . . . . . . . . . . . . . . . 67
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Tyre Mobility System . . . . . . . . . . . . . . . . . . . . . 262
Tyre mobility system . . . . . . . . . . . . . . . . . . . . . 255
Tyre pressure . . . . . . . . . . . . . . . . . . . . . 66, 90, 245 Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Tyre pressure monitoring . . . . . . . . . . . . . . . . . 246
Tyre pressure monitoring system . . . . . . . . . . . . 89
Tyre pressures . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Tyre repair kit Tyre Mobility System . . . . . . . . . . . . . . . . . . 262
Tyres and wheels Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 251
Tyres service life . . . . . . . . . . . . . . . . . . . . . . . . 248
Tyres tread depth . . . . . . . . . . . . . . . . . . . . . . . 249
Tyres with directional tread pattern . . . . . . . . . 245
UUnderbody protection . . . . . . . . . . . . . . . . . . . . 219VVehicle data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
Vehicle identification data . . . . . . . . . . . . . . . . 298
Vehicle identification number . . . . . . . . . . . . . 298
Vehicle keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
ExeoST_EN.book Seite 320 Freitag, 3. September 2010 11:41 11