lights Seat Exeo ST 2010 Manual Online

If and when
280Changing tail light bulbs (on side panel)Overview of tail lightsTail lights on side panel•Brake lights and side lights•Turn signal
Overview of tail lights. LED lampsTail lights on side panel•Brake lights and side lights•Turn signalNote
•It is only possible to change the turn signal light.•If the warning lamp for the brake light or side light (LED lamp) lights up,
the tail light assembly should be replaced.•The failure of the lamp is only shown when the LED function goes out
completely. Sometimes, a LED will stop working, without displaying the
warning as the function continues to operate.
Fig. 222 Overview of tail
lights
Fig. 223 Overview of tail
lights
ExeoST_EN.book Seite 280 Freitag, 3. September 2010 11:41 11

If and when283
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Position of the bulbs
Changing bulbs. LED lamps
All bulbs can be changed easily in the bulb holder.The bulb is secured with a bayonet fastening. The table below gives
an overview of the bulb positions.
– Lightly press the defective bulb into the bulb holder, then turn it
to the left and remove it. – Fit the new bulb, pressing it into the bulb holder and turn it to the
right as far as it will go.
– Use a cloth to remove any fingerp rints from the glass part of the
bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒page 283.
Position of the bulbsFitting the bulb holder
The bulb holder is easy to fit.
Pos. ⇒ page 282,
fig. 227
Bulb function
A
Turn signal
B
Brake lights and side lights
Fig. 228 Position of the
bulbs in the bulb holder:
Example: Outer left tail
light
Pos. ⇒ fig. 228
Bulb function
A
Turn signal
Fig. 229 Securing the
bulb holder in the tail
light unit
ExeoST_EN.book Seite 283 Freitag, 3. September 2010 11:41 11

If and when
284
– Check that the seal is seated correctly on the bulb holder.
– Position the bulb holder on the tail light and align it so that it is securely seated.
– Press the bulb holder into the tail light until it engages.
– Check that all four retaining tabs ⇒page 283, fig. 229 -arrows-
have engaged.
– Re-install the tail light unit ⇒page 284.Fitting the tail light unit
The tail light unit is easy to fit.
– First place the tail light unit in ⇒fig. 230 arrow in the
housing.
– Gently press the tail light unit against the housing, first in posi- tion and then in position , until that the clips engage firmly
in the rubbe r mountings.
– Apply gentle pressure to the front side of the tail light unit and secure using the screwdriver, from the luggage compartment
⇒ fig. 231 .
– Try to move the tail light sideways to ensure it is correctly fitted.
– Fit the cover back onto the screw, with the notch pointing to the rear .
– Put the screwdriver back into the tool kit.
– Make sure that all bulbs for the tail lights are working.
Fig. 230 Fitting the tail
light unit
Fig. 231 Luggage
compartment: Location of
the bolt securing the tail
light unit
A1
A2
A3
A1
A2
ExeoST_EN.book Seite 284 Freitag, 3. September 2010 11:41 11

If and when285
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Caution
Take care when fitting the tail light unit to make sure there is no damage to
the paintwork or any of its components.Changing tail light bulbs (on tailgate)Overview of tail lightsTail lights on the tailgate•Rear side lights•Rear fog light•Reverse lights
Overview of tail lights. LED lampsTail lights on the tailgate•Rear side lights•Rear fog light•Reverse lightsNote
•It is only possible to replace the rear fog lamp and the reversing light.•If the warning lamp for the side light (LED lamp) lights up, the tail light
assembly should be replaced. •The failure of the lamp is only shown when the LED function goes out
completely. Sometimes, a LED will stop working, without displaying the
warning as the function continues to operate.
Fig. 232 Overview of tail
lights
Fig. 233 Overview of tail
lights
ExeoST_EN.book Seite 285 Freitag, 3. September 2010 11:41 11

If and when
286Remove the bulb holder
The tailgate must be open to change the bulbs.
You can access the bulb holder for the inner tail lights via the inside
of the tailgate.
– Check which of the bulbs is defective.
– Take the screwdriver out of the vehicle's tool kit ⇒page 254.
– Insert the screwdriver into the opening in the cover ⇒fig. 234
and detach the cover .
– Press on the tabs ⇒ fig. 235 in the direction of the arrows
and remove the bulb holder by pulling in the direction of the
arrow .
– Change the bulbs ⇒page 287 ⇒page 287.
WARNING
If a bulb is replaced in a tail light assembly with LED, do not pull too hard
on the bulb holder to avoid damaging the wiring of the LED module.
Fig. 234 Remove the
cover of the tailgate trimFig. 235 Remove the bulb
holder
A1
A2
AA
AB
ExeoST_EN.book Seite 286 Freitag, 3. September 2010 11:41 11

If and when287
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Changing bulbs
All bulbs can be changed easily in the bulb holder.The bulbs are secured with a bayonet fastener. The table below
gives an overview of the bulb positions.
– Lightly press the defective bulb into the bulb holder, then turn it
to the left and remove it.
– Fit the new bulb, pressing it into the bulb holder and turn it to the
right as far as it will go.
– Use a cloth to remove any fingerp rints from the glass part of the
bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒page 288.
Position of the bulbsChanging bulbs. LED lamps
All bulbs can be changed easily in the bulb holder.The bulbs are secured with a bayonet fastener. The table below
gives an overview of the bulb positions.
– Lightly press the defective bulb into the bulb holder, then turn it
to the left and remove it.
Fig. 236 Position of the
bulbs in the bulb holder.
Example: Tail lights on the
tailgate
Pos. ⇒ fig. 236
Bulb function
A
Reverse lights
B
Rear side lights
C
Rear fog light
Fig. 237 Position of the
bulbs in the bulb holder.
Example: Tail lights on the
tailgate
ExeoST_EN.book Seite 287 Freitag, 3. September 2010 11:41 11

If and when
288
– Fit the new bulb, pressing it into the bulb holder and turn it to the right as far as it will go.
– Use a cloth to remove any fingerp rints from the glass part of the
bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒ page 288.Position of the bulbsFitting the bulb holder
The bulb holder is easy to fit.– Position the bulb holder on the tail light and align it so that it is
securely seated.
– Press the bulb holder into the tail light until it engages.
– Fit the cover back in the interior trim so that it engages.
– Put the screwdriver back into the tool kit.
– Make sure that all bulbs for the tail lights are working.
Side turn signals– Press the turn signal to the left or to the right to remove the bulb.
– Remove the bulb holder from the turn signal.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the bulb holder in the turn signal guide until it clicks into place.
– First place the turn signal in th e opening in the bodywork, fixing
the tabs ⇒ fig. 238, arrow .
– Insert the bulb as shown by the arrow ⇒fig. 238.
Pos. ⇒ page 287,
fig. 236
Bulb function
A
Reverse lights
B
Rear fog light
Fig. 238 Side turn signal
A1
A2
ExeoST_EN.book Seite 288 Freitag, 3. September 2010 11:41 11

If and when289
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Luggage compartment lights– Remove the tulip-shaped fitting by pressing on its inside edge
using the flat side of a screwdriver. – Remove the protective cover and remove the bulb from the
housing.
Fig. 239 Luggage
compartment lightFig. 240 Luggage
compartment light
ExeoST_EN.book Seite 289 Freitag, 3. September 2010 11:41 11

If and when
292How to jump start: descriptionOn ⇒fig. 245 shows the flat battery and the charged battery.
Jump lead terminal connections
– Switch off the ignition of both vehicles ⇒.
1. Connect one end of the red jump lead to the positive ⇒fig. 245
terminal of the vehicle with the flat battery ⇒.
2. Connect the other end of the red jump lead to the positive terminal in the vehicle providing assistance.
3. Connect one end of the black jump lead to the negative terminal on the battery of the vehicle providing assistance. 4. Connect the other end of the black jump lead to a solid metal
component which is bolted on to the engine block, or onto the
engine block itself of the vehicle with the flat battery. Do not
connect it to a point near the battery ⇒.
5. Position the leads in such a way that they cannot come into contact with any moving parts in the engine compartment.
Starting
6. Start the engine of the vehicle with the boosting battery and let it run at idling speed.
7. Start the engine of the vehicle with the flat battery and wait one or two minutes until the engine is running.
Removing the jump leads
8. Before you remove the jump lead s, switch off the headlights (if
they are switched on).
9. Turn on the heater blower and heated rear window in the vehicle with the flat battery. This helps minimise voltage peaks which are
generated when the leads are disconnected.
10. When the engine is running, disconnect the leads in reverse order to the details given above.
Connect the battery clamps so they have good metal-to-metal contact with
the battery terminals.
If the engine fails to start, switch off the starter after about 10 seconds and
try again after about half a minute.
Fig. 245 How to connect
the jump leads
AA
AB
A+
A+
A-
AX
ExeoST_EN.book Seite 292 Freitag, 3. September 2010 11:41 11

If and when295
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Do not pull too hard with the towing vehicle and take care to avoid jerking the
tow-rope. When towing on an unpaved road, there is always a risk of over-
loading and damaging the anchorage points.
The ignition of the vehicle being towed must be switched on to prevent the
steering wheel from locking and also to allow the use of the turn signals,
horn, windscreen wipers and washers.
As the brake servo does not work if the engine is not running, you must apply
considerably more pressure to the brake pedal than you normally would.
As the power assisted steering does not work if the engine is not running, you
will need more strength to steer than you normally would.
Towing vehicles with an automatic gearbox
•Put the selector lever into position “N”.•Do not drive faster than 50 km/h when towing a vehicle.•Do not tow further than 50 km.•If a breakdown vehicle is used, the vehicle must be towed with the front
wheels raised.Note
•Observe legal requirements when towing or tow-starting.•Switch on the hazard warning lights of both vehicles. However, observe
any regulations to the contrary.•For technical reasons, vehicles with an automatic gearbox must not be
tow-started.•If damage to your vehicle means that there is no lubricant in the gearbox,
you must raise the drive wheels while the vehicle is being towed.•If the vehicle has to be towed more than 50 km, the front wheels should
be raised during towing, and towing should be carried out by a qualified
person.
•The steering wheel is locked when the vehicle has no electrical power. The
vehicle must then be towed with the front wheels raised. Towing should be
carried out by a qualified person.•The towing eye should always be kept in the vehicle. Please refer to the
notes ⇒page 294, “Tow-starting”.Front towing eyeFitting the towing eye
– Take the towing ring from the on-board tool set.
– Remove the front cover by pressing down on the right hand side.
– Bolt the eye to its limit to the left, in the direction of the arrow
⇒ fig. 246 .
Fig. 246 Fitting the
towing eye to front rear of
the vehicle
ExeoST_EN.book Seite 295 Freitag, 3. September 2010 11:41 11