steering Seat Ibiza 5D 2009 Owner's Guide
[x] Cancel search | Manufacturer: SEAT, Model Year: 2009, Model line: Ibiza 5D, Model: Seat Ibiza 5D 2009Pages: 257, PDF Size: 6.5 MB
Page 99 of 257

Lights and visibility97
Safety First
Controls and equipment
Practical tips
Technical Data
Note
•Do not put stickers on the windscreen in front of the sensor. This may 
cause sensor disruption or faults.Rear window wiper 
 
The windscreen wiper lever operates the windscreen wiper 
and the wash and wipe system for the rear window.
Switching on the interval wipe
– Press the lever forwards to position    ⇒fig. 63 . The wiper will 
wipe the window approximately every 6 seconds. Switching off the interval wipe function
– Pull the lever back from position   towards the steering wheel. 
The wiper will continue to function  for a short period if you switch 
off whilst the wipers are in motion.
Switching on the windscreen wiper and washer system
– Press the lever fully fo rwards to position   ⇒fig. 63 . The rear 
wiper and washer operate at the same time. The windscreen 
wash system will function as long  as you hold the lever in this 
position.
– Release the lever. The washer system stops and the wipers  continue until the end of the cycle.
– Move the lever towards the steering wheel to switch off.
WARNING
•A worn or dirty wiper blade will obstruct visibility and reduce safety.•Always note the corresponding warnings on  ⇒page 188.Caution
In icy conditions, always check that the wiper blade is not frozen to the glass 
before using the wiper for the first time. If you switch on the wiper when the 
wiper blade is frozen to the glass, this could damage both the wiper blade 
and the wiper motor.
Note
•The rear window wiper will only work when the ignition is switched on.•Depending on the version of the model, when you engage reverse gear 
and with the headlight wiper activated, the lamps are wiped.
Fig. 63  Windscreen wiper 
and windscreen wash 
lever: rear window wiper
A6
A6
A7
Ibiza_EN.book  Seite 97  Montag, 14. September 2009  6:19 18 
Page 100 of 257

Lights and visibility
98Headlight washer system
The headlight washers clean the headlight lenses.The headlight washers are activated automatically when the windscreen 
washer is used and the windscreen wiper lever is pulled towards the steering 
wheel for at least 1.5 seconds – provided the dipped headlights or main 
beams are switched on. Clean off stubborn dirt (insects, etc.) from the head-
lights at regular intervals, for instance when filling the fuel tank.
Note
•To ensure that the headlight washers work properly in winter, keep the 
nozzle holders in the bumper free of snow and remove any ice with a de-icer 
spray.•To remove water, the windscreen wipers will be activated from time to 
time, the headlight wipers will be activated every three cycles.Rear-view mirrorsAdjusting the head restraintsBefore beginning any journey, adjust the rear-view mirrors for correct 
visibility.
Interior mirror
It is dangerous to drive if yo u cannot see clearly through the 
rear window.Manual anti-dazzle function for interior mirror
In the basic mirror position, the lever at the bottom edge of the mirror should 
be at the front. Pull the lever to the back to select the anti-dazzle function.Automatic anti-dazzle interior mirror*
The automatic anti-dazzle function can be switched on and off 
as desired.Switching off anti-dazzle function
–Press button   ⇒ fig. 64. Warning lamp   goes out:
Fig. 64  Automatic anti-
dazzle interior mirror.
AA
AB
Ibiza_EN.book  Seite 98  Montag, 14. September 2009  6:19 18 
Page 103 of 257

Seats and stowage101
Safety First
Controls and equipment
Practical tips
Technical Data
Seats and stowageThe importance of correct seat adjustmentProper seat adjustment optimises the level of protection 
offered by seat belts and airbags.Your vehicle has five seats, two on the front part and three on the rear part. 
Each seat is equipped with a three-point seat belt.
The driver seat and the front passenger seat can be adjusted in many ways to 
suit the physical requirements of the vehicle occupants. The correct seat 
position is very important for:•a fast and easy operation of all controls on the instrument panel,•a relaxed posture which does not cause drowsiness,•a safe driving ⇒ page 7,•ensuring that the seat belts and airbag system provide maximum protec-
tion  ⇒page 16.WARNING
•If the driver and passengers assume improper sitting positions, they 
may sustain critical injuries.•More people than available seats must never be transported in your 
vehicle.•Every passenger in the vehicle must properly fasten and wear the seat 
belt belonging to his or her seat. Chil dren must be protected with an appro-
priate child restraint system  ⇒page 38, “Child safety”.•The front seats and all head restraints must always be adjusted to body 
size and the seat belt must always be properly adjusted to provide you and 
your passengers with optimum protection.
•Always keep your feet on the foot well when the vehicle is moving; 
never rest them on the dash panel, out of the window or on the seat. This 
is also applied to passengers. An incorrect sitting position exposes you to 
an increased risk of injury in case of a sudden braking or an accident. If the 
airbag is triggered, you could sustain severe injuries due to an incorrect 
sitting position.•It is important for the driver and front passenger to keep a distance of 
at least 25 cm from the steering wheel or dash panel. Failure to respect the 
minimum distance means that the airbag will not protect you. Risk of fatal 
injury. The distance between the driver and the steering wheel or between 
the front passenger and the dash panel should always be as great as 
possible.•Adjust the driver or front passenger seat only when the vehicle is 
stationary. Otherwise, your seat  could move unexpectedly while the 
vehicle is moving. This could increase the risk of an accident and therefore, 
injury. In addition, while adjusting your seat, you will assume an incorrect 
sitting position. Risk of fatal accidents.•Special guidelines apply to installing a child seat on the front 
passenger seat. When installing a child seat, please observe the warnings 
described in  ⇒page 38, “Child safety”.WARNING (continued)
Ibiza_EN.book  Seite 101  Montag, 14. September 2009  6:19 18 
Page 129 of 257

Driving127
Safety First
Controls and equipment
Practical tips
Technical Data
DrivingAddressAdjusting the steering wheel position
The height and reach of the steering wheel can be freely 
adjusted to suit the driver.– Adjust the driver seat to the correct position.
–Push the lever  ⇒fig. 93  under the steeri ng column down  ⇒.
– Adjust the steering wheel until the correct position is set  ⇒fig. 93.
– Then push the lever up again firmly  ⇒.
WARNING
•Incorrect use of the steering column adjustment function and an incor-
rect seating position can result in serious injury.•To avoid accidents, the steering column should be adjusted only when 
the vehicle is stationary.•Adjust the driver's seat or steering wheel so that there is a distance of 
at least 25 cm between the steering wheel and your rib cage  ⇒fig. 93. If 
you fail to observe the minimum distance, the airbag will not protect you. 
Risk of fatal injury.•If your physical constitution does not allow you to maintain the 
minimum distance of 25 cm, contact an Authorised Service Centre. The 
Authorised Service Centre will help you  to decide if special specific modifi-
cations are necessary.•If you adjust the steering wheel so that it points towards your face, the 
driver airbag will not protect you properly in the event of an accident. Make 
sure that the steering wheel points towards your chest.•When driving, always hold the steering wheel with both hands on the 
outside of the ring at the 9 o'clock and 3 o'clock positions. Never hold the 
steering wheel at the 12 o'clock position, or in any other manner (e.g. in 
the centre of the steering wheel, or on  the inside of the rim). In such cases, 
you could receive severe injuries to the arms, hands and head.
Fig. 93  Steering column 
height adjustment
Ibiza_EN.book  Seite 127  Montag, 14. September 2009  6:19 18 
Page 131 of 257

Driving129
Safety First
Controls and equipment
Practical tips
Technical Data
Ignition lockPosition of the ignition keyIgnition switched off, steering lock 
In this position  ⇒fig. 95 the ignition and the engine are OFF and the steering 
may be locked.
For the  Steering lock to operate without the ignition key, turn the steering 
wheel until it locks with an audible sound. You should always lock the 
steering wheel when you leave your vehicle. This will help prevent vehicle 
theft  ⇒ .
Switching the ignition or the glow plug system on 
Turn the ignition key to this position and release it. If the key cannot be turned 
or it is difficult to turn from position   to position  , move the steering 
wheel from one side to the other until it is released. Starting 
The engine is started when the key is in this position. Electrical components 
with a high power consumption are switched off temporarily.
Every time the vehicle is started again, the ignition key must be turned to 
position . The 
repetitive start prevention lock  of the ignition prevents 
possible damage to the starter motor if the engine is already running.
WARNING
•The ignition key must NOT be removed from the lock until the vehicle 
comes to a standstill. Otherwise, the steering could be immediately 
blocked- Risk of accident!•Always remove the key from the ignition lock when leaving the vehicle, 
even for a short period. This is especially important if children or disabled 
people are left alone in the vehicle. They could accidentally start the 
engine or work electrical equipment  such as the electric windows, conse-
quently resulting in an accident.•Unsupervised use of the keys could start the engine or any electrical 
system, such as the electric window. This could result in serious injury.Caution
The starter motor will only work when the engine is stopped (ignition key 
position ).Electronic immobiliser
The immobiliser prevents unauthorised persons from driving 
the vehicle.There is a micro-chip in the key that deactivates the electronic immobiliser 
automatically when the key is inserted into the ignition.
Fig. 95  Ignition key posi-
tions
A1
A2
A1
A2
A3A1A3
Ibiza_EN.book  Seite 129  Montag, 14. September 2009  6:19 18 
Page 134 of 257

Driving
132After switching the engine off, the radiator fan may run on for up to 10 
m i n u t e s .  I t  is  a l s o  p o ss i b l e  t h a t  t h e  fa n  t u r ns  i t s e l f  o n  o n ce  m o r e  i f  t h e  co o la n t  
temperature increases due to the heat accumulated in the engine compart-
ment or due to its prolonged exposure to solar radiation.
WARNING
•Never switch the engine off until the vehicle is completely stationary.•The brake servo works only when the engine is running. With the 
engine switched off, more strength is needed to brake. As normal brake 
operation cannot be performed, risk  of accidents and serious injury may 
exist.•The steering lock can be immediately blocked once the key is removed 
from the ignition lock. The vehicle cannot be steered. Risk of accident.Caution
If the engine has been driven hard for a long period, the engine could over-
heat when it is switched off. Risk of engine damage. For this reason, you 
should idle the engine for approx. 2 minutes before you switch it off.
Manual gearboxDriving a car with a manual gearboxEngaging the reverse gear
– The vehicle should be stationary with the engine idling. Press the  clutch down thoroughly.
– Place the gear lever into neutral and push the lever downwards.
– Slide the gear lever to the left, and then into the reverse position  shown on the gear stick.Certain versions of the model may include a 6-speed manual gearbox, and its 
diagram is shown on the gear stick.
The reverse gear can only be engaged when the vehicle is stationary. When 
the engine is running and before engaging this gear, wait about 6 seconds 
with the clutch pressed down thoroughly in order to protect the gearbox.
Fig. 96  Centre Console: 
gear shift pattern of a 5-
speed manual gearbox
Ibiza_EN.book  Seite 132  Montag, 14. September 2009  6:19 18 
Page 139 of 257

Driving137
Safety First
Controls and equipment
Practical tips
Technical Data
Changing gear with the Tiptronic gear system*
The Tiptronic system allows the driver to select gears manu-
ally
General information about driving in Tiptronic mode
Changing gear with Tiptronic
– Press the selector lever from position D  to the right into the 
Tiptronic selector gate.
– Lightly press the selector forward + to change up into high gears.
– Lightly press the selector lever  backwards - to change down into 
low gears.
Changing gear with the steering wheel paddle levers*
– Press the right paddle lever    towards the steering wheel to 
change up ⇒ fig. 102.
– Press the left paddle lever   towards the steering wheel to  change down ⇒ fig. 102.Using the paddle levers on the steering wheel, you can access manual driving 
mode regardless of the driving mode pre-selected.
General information about driving in Tiptronic mode
When accelerating, the automatic gearbox / DSG automatic gearbox goes 
into a higher gear a little before the engine reaches its maximum permitted 
revolutions.
If a lower gear is selected, the automatic gearbox / DSG automatic gearbox 
will only change down when the engine cannot go over its maximum 
permitted revolutions.
If the “Tiptronic” is selected suddenly while the vehicle is in motion and the 
automatic gearbox / DSG automatic gearbox is in 3rd gear in selector lever 
position  D, the “Tiptronic” will then also be in 3rd gear.
Fig. 101  Changing gear 
with TiptronicFig. 102  Steering wheel 
with paddle levers for 
automatic gearbox
A+A–
Ibiza_EN.book  Seite 137  Montag, 14. September 2009  6:19 18 
Page 140 of 257

Driving
138Changing gears in the normal or sport programme using the steering wheel 
paddle levers
If the paddle levers ⇒ page 137, fig. 102 are used in the normal or sport 
programme, the system switches temporarily to “Tiptronic” mode. To exit 
“Tiptronic” mode again, press the right paddle lever   towards the steering 
wheel for approximately one second. You will also leave “Tiptronic” mode if 
the paddle levers are not moved for a certain time.
Note
•The gear paddle levers on the steering wheel can be operated with the 
gear stick in any position and with the vehicle in motion.Selector lever positions
The selector lever positions and gears are shown on the 
instrument panel screen.
Selector lever positions
The selected gear is displayed on the side of the selector lever and on the 
instrument panel screen. The currently selected gear for the automatic 
gearbox will also be shown on the screen.
Tiptronic gear indicator
If the automatic gearbox is shifted manually, the selected gears are shown on 
the screen.
P - parking lock
When the selector lever is in this position, the drive wheels are locked 
mechanically.
Position P on the lever must only be selected if the vehicle is stationary.
To move selector lever from position  P, the locking button in the selector lever 
handle must be pressed and the brake pedal depressed at the same time 
with the ignition switched on.
To put the selector lever in position  P, simply press the lock button down and, 
if necessary, depress the brake pedal down.
R -Reverse gear
The reverse gear is engaged in this position.
Reverse gear must be engaged only when the vehicle is stationary and the 
engine is idling.
To move the selector lever to position  R, press the lock button down and, at 
the same time, press the brake pedal down, with the ignition switched on.
With the selector lever in position  R and the ignition switched on the 
following occurs:•Reverse lights light up.•The air conditioning automatically changes the air recirculation mode.•The wiper starts if the windscreen washer is on.•The parking distance warning system switches on.*
+Fig. 103  Automatic 
gearbox: Display on the 
instrument panel
Ibiza_EN.book  Seite 138  Montag, 14. September 2009  6:19 18 
Page 141 of 257

Driving139
Safety First
Controls and equipment
Practical tips
Technical Data
N - Neutral (idling)
If this position is selected, the gearbox is in neutral. Power is not transmitted 
to the wheels and the engine does not have a braking function.
Never use the 
N position to drive down a hill. The engine does not function as 
a brake and the brakes are subjected to excessive stain.
You could damage the automatic gearbox if you drive down hills with the 
selector lever in position  N and the engine switched off.
D - Drive (forwards)
In this position the gearbox automatically changes to a lower or higher gear, 
according to the engine requirements, driving style and speed. The braking 
effect of the engine when driving downhill is very limited when the selector is 
in this position. The instrument panel screen displays the selected gear as 
well as the selector lever in position  D.
If position  N has been selected and you wish to select  D, you must press the 
foot brake if the vehicle is stationary, or travelling at under 5 km/h.
S - Standard driving position (Sport programme)
When the selector lever is in position  S, it will automatically change up into a 
h igh er  gea r late r,  an d change  d own i nto a  low g ea r,  if  com pare d  wi th p osi ti on 
D . This way, it is possible to take full advantage of the engine reserve power, 
depending on the engine demand, driving style and speed. The braking 
effect of the engine when driving downhill is very limited. On the instrument 
panel screen the selected gear is shown as well as the selector lever to posi-
tion  S.
To select gear range  S, press the lock button on the selector lever.
WARNING
If the vehicle moves with no control, an accident and serious injury may 
occur.•As a driver, you should never leave your vehicle if the engine is running 
and a gear is engaged. If you have to leave your vehicle while the engine is  running, you must always apply the parking brake and engage parking lock 
P.
•If the engine is running and if D or R are engaged, you will need to hold 
the vehicle stopped by depressing footbrake down. The car would creep 
forward as the power transmission is not fully interrupted even when the 
engine is idling.•Never accelerate when changing gear or you may cause an accident.•Never move the selector lever to “R” or “P” when driving. Risk of acci-
dent.•Before driving down a very steep slope, reduce your speed and shift to 
position 1st.•Always hold the vehicle on the foot brake if you stop uphill. Otherwise, 
the vehicle could roll back.•Never allow the brake to rub and do not use the brake pedal too often 
or for long periods. Constant braking will cause the brakes to overheat and 
will considerably reduce the braking effect. This increases the braking 
distance and could cause the brake system to fail.WARNING
Never switch the engine off until the vehicle is stationary. You could lose 
control of your vehicle. This could cause an accident and serious injury.•The airbags and belt tensioners do  not work when the ignition is 
switched off.•The brake servo does not work when the engine is not running. You 
need more force to stop the vehicle.•Power assisted steering does not work when the engine is not running. 
That is why it is much more difficult to turn the steering wheel.•Never remove the key from the ignition if the vehicle is in motion. The 
steering lock could suddenly engage, and you would not be able to steer 
the vehicle.WARNING (continued)
Ibiza_EN.book  Seite 139  Montag, 14. September 2009  6:19 18 
Page 143 of 257

Driving141
Safety First
Controls and equipment
Practical tips
Technical Data
Always apply the handbrake 
firmly. This prevents you driving with the hand-
brake applied ⇒ .
The handbrake warning lamp 
 lights up when the handbrake is applied 
and the ignition is switched on. The warning turns off when the handbrake is 
released.
WARNING
•Never use the handbrake to stop the  vehicle when it is in motion. The 
braking distance is considerably longer, because braking is only applied to 
the rear wheels. Risk of accident!•If it is only partially released, this will cause rear brakes overheating, 
which can impair the function of the brake system and could lead to an acci-
dent. This also causes premature wear on the rear brake pads.Caution
Always apply the handbrake before you leave the vehicle. The first gear 
should also be selected.Parking
The handbrake should always be firmly applied when the 
vehicle is parked.Always note the following points when parking the vehicle:
– Use the foot brake to stop the vehicle.
– Apply the handbrake.
– The first gear should also be selected. – Switch the engine off and remove the key from the ignition lock. 
Turn the steering wheel slightly to engage the steering lock.
– Always take you car keys with you when you leave the vehicle  ⇒ .
Additional notes on parking the vehicle on gradients:
Turn the steering wheel so that the vehicle rolls against the kerb if it started 
to roll.•If the vehicle is parked facing  downhill, turn the front wheels so that they 
point  towards the kerb .•If the vehicle is parked facing  uphill, turn the front wheels so that they 
point  away from the kerb .•Secure the vehicle as normal by applying the handbrake firmly and 
engaging first gear.WARNING
•Take measures to reduce the risk of injury when you leave your vehicle 
unattended.•Never park where the hot exhaust system could ignite inflammable 
materials, such as dry grass, low bushes, spilt fuel etc.•Never allow vehicle occupants to remain in the vehicle when it is 
locked. They would be unable to open the vehicle from the inside, and 
could become trapped in the vehicle in an emergency. In the event of an 
emergency, locked doors will delay assistance to occupants.•Never leave children alone in the vehicle. They could set the vehicle in 
motion, for example, by releasing the handbrake or the gear lever / 
selector lever.•Depending on weather conditions, it may become extremely hot or cold 
inside the vehicle. This can be fatal.
Ibiza_EN.book  Seite 141  Montag, 14. September 2009  6:19 18