light Seat Ibiza SC 2014 Owner's manual
[x] Cancel search | Manufacturer: SEAT, Model Year: 2014, Model line: Ibiza SC, Model: Seat Ibiza SC 2014Pages: 240, PDF Size: 4.89 MB
Page 206 of 240

Advice
Changing the tail light bulbs 3 Applies to the model: IBIZA/IBIZA SC
Fig. 196
Changing the tail light bulbs Fig. 197
Changing the tail light bulbs –
Remove the connector from housing A›››
Fig. 195 . –
Remo ve the bulb holder, separating it from
the casing. To do this, press tabs B in the
direction of the arrows ››› Fig. 196 .
– When the b u
lb holder has been removed,
press in the direction of the arrow 1 and
at the same time, turn in the direction of
the arrow 2
››› Fig. 197
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed.
Changing the tail light bulbs
(on the side panel)
Overview of tail lights 3 Applies to the model: IBIZA ST
Tail lights on side panel Bulb lamps â— Brake lights
â— Side lights
â— Turn signal Tail lights on side panel LED lamps
â—
Brake light (LED)
â— Side light (LED)
â— Turn signal
Accessing the side light bulbs 3 Applies to the model: IBIZA ST
Fig. 198
Lights on the side. –
Open the rear lid.
– Look for a lid with a grill behind the side
lights.
– Remove the lid with a flat screwdriver, plac-
ing it in notch A
››› Fig. 198 .
204
Page 207 of 240

Fuses and bulbs
Changing bulbs 3 Applies to the model: IBIZA ST
Fig. 199
Removing the bulb holder. –
Remove the bulb holder by pressing the
fastening clip B
››› Fig. 199 and pulling it
outw ar
ds.
– Replace the faulty bulb, rotating it to the
left and outwards.
– To refit follow the steps in reverse order,
taking special care when fitting the bulb
holder.
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed. Changing the tail light bulbs
(on the rear lid)
Overview of tail lights 3 Applies to the model: IBIZA ST
Light s
on the rear lid Bulb lamps
â— Reverse lights
â— Side lights
â— Fog lights
Lights on the rear lid LED lamps
â— Reverse lights
â— Side light (LED)
â— Fog lights
Accessing the rear lid lights 3 Applies to the model: IBIZA ST
Fig. 200
Lights on the boot. –
Open the rear lid.
– On the rear lid lining there is a lid behind
each light.
– Remove the lid with a flat screwdriver, plac-
ing it in notch A
››› Fig. 200 .
Ch an
ging bulbs 3 Applies to the model: IBIZA ST
Fig. 201
Removing the bulb holder. –
Remove the bulb holder by pressing the
fastening clips B
››› Fig. 201 and pulling
outw ar
ds.
– Replace the faulty bulb, rotating it to the
left and outwards.
– To refit follow the steps in reverse order,
taking special care when fitting the bulb
holder.
»
205
Technical specifications
Advice
Operation
Safety
The essentials
Page 208 of 240

Advice
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed.
Changing the side and interior
bulbs
Turn signals Fig. 202
Turn signals. –
Press the turn signal to the left or to the
right to remove the bulb.
– Remove the bulb holder from the turn sig-
nal. –
Remove the failed bulb and replace with a
new bulb.
– Insert the bulb holder in the turn signal
guide until it clicks into place.
– First fit the turn signal in the opening in the
chassis, fastening the tabs 1
››› Fig. 202 ,
and then fit in the b
ulb as shown by the ar-
row 2
››› Fig. 202 .
Number p l
ate light 3 Applies to the model: IBIZA/IBIZA SC
– Insert the flat part of a screwdriver into the
special slot and remove the bulb.
– Remove the bulb holder, by turning it until
it is free.
– Change the bulb.
– Replace the bulb holder, by turning it until
it fits fully.
– Fit the light into the space and press until
you hear a “clickâ€. Number plate light 3 Applies to the model: IBIZA ST
Fig. 203
Remove the number plate light. –
Insert the flat part of a screwdriver into the
special slot and remove the number plate
light from its moulding.
– Remove the connector and extract the bulb.
After changing the bulb, fit the connector
again.
– Place the light in its moulding, pressing the
left side. Once it is fitted into place, press
the right side until you hear a click.
206
Page 209 of 240

Fuses and bulbs
Interior light and front reading lights Fig. 204
Front reading light. To remove the glass
– Insert a fine screwdriver between the cas-
ing and the glass ››› Fig. 204 .
– Car
efully remove the glass, levering it to
avoid possible damage.
To replace the bulbs
– Pull the bulbs outwards.
– To remove the central bulb, hold and press
to one side.
Assembly
– Proceed in the reverse order, pressing gen-
tly on the outer edge of the side light.
– First fit the glass with the fastening tabs
over the frame of the switch. Next press the front part until the two long tabs click on
the support.
Additional brake light* Given the difficulty involved in the replace-
ment of this light it should be done by Tech-
nical Services.
Luggage compartment light* Fig. 205
Boot light. Fig. 206
Boot light. –
Remove the tulip-shaped fitting by pressing
on its inside edge (arrow) using the flat
side of a screwdriver ››› Fig. 205 .
– Pr e
ss the bulb sideways and remove it from
its housing ››› Fig. 206.
207
Technical specifications
Advice
Operation
Safety
The essentials
Page 212 of 240

Technical specifications
Special versions, optional equipment fittings
or retro-fitting accessories will increase the
weight of the vehicle ››› .
WARNING
â— Please note that the centre of gravity may
shift when transporting heavy objects; this
may affect vehicle handling and lead to an ac-
cident. Always adjust your speed and driving
style to suit road conditions and require-
ments.
â— Never exceed the gross axle weight rating
or the gross vehicle weight rating. If the per-
missible axle load or the permissible total
weight is exceeded, the driving characteris-
tics of the vehicle may change, leading to ac-
cidents, injuries and damage to the vehicle. Towing a trailer
Trailer weights Trailer weight
The trailer weights and drawbar loads ap-
proved are selected in intensive trials accord-
ing to precisely defined criteria. The ap-
proved trailer weights are valid for vehicles in
the
EU
for maximum speeds of 80 km/h (50
mph) (in c ertain circumstances up to 100
km/h (62 mph)). The figures may be different
in other countries. All data in the official vehi- cle documentation takes precedence over
these data at all times
››› .
Drawbar loads
The maximum
permitted drawbar load on the
b
all joint of the towing bracket must not ex-
ceed
75 kg.
In the interest of road safety, we recommend
that you always tow approaching the maxi-
mum drawbar load. The response of the trail-
er on the road will be poor, if the drawbar
load is too small.
If the maximum permissible drawbar load
cannot be met (e.g. with small, empty and
light-weight single axle trailers or tandem
axle trailers with a wheelbase of less than 1
metre), a minimum of 4% of the actual trailer
weight is legally required for the drawbar
load. WARNING
â— For safety reasons, you should not drive at
speeds above 80 km/h (50 mph) when towing
a trailer. This also applies in countries where
higher speeds are permitted.
â— Never exceed the maximum trailer weights
or the drawbar load. If the permissible axle
load or the permissible total weight is excee-
ded, the driving characteristics of the vehicle
may change, leading to accidents, injuries
and damage to the vehicle. Wheels
Tyre pressure, snow chains, wheel
bolts Tyre pressures
The sticker with the tyre pressure values can
be found on the inside of the fuel tank flap.
The tyre pressure values given there are for
cold tyres. Do not reduce the slightly raised
pr
e
ssures of warm tyres ››› .
Snow chains
Snow chains may be fitted only to the front
wheels, and only for the following tyres:
175/70R14
185/60R15Chains with links not exceeding 15 mm
(including the chain closure)
215/45R16Chains with links not exceeding 9 mm
(including the chain closure)
215/40R17Chains with links not exceeding 7 mm
(including the chain closure) Wheel bolts
After the wheels have been changed, the
tightening torque
of the wheel bolts should
be c hec
ked as soon as possible with a torque
wrench ››› . The tightening torque for steel
and alloy wheels is 120 Nm.
210
Page 214 of 240

Technical specifications
Engine specifications Petrol engine 1.2 44 kW (60 PS) Engine specificationsPower output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm
3
)Fuel
44 (60)/5,200108/3,0003/1,198Super 95 RON a)
/Normal 91 RON b)
a)
Research Octane Number = Anti-detonation rating of the petrol.
b) Slight power loss.
PerformanceIBIZAIBIZA SCIBIZA ST
Top speed (km/h)155 (4)155 (4)155 (4)
Acceleration from 0-80 km/h (seconds)10.310.310.8
Acceleration from 0-100 km/h (seconds)15.915.916.7
Weights (in kg)
Gross vehicle weight1,5401,5401,605
Weight in running order (with driver)1,0491,0491,110
Gross front axle weight820820835
Gross rear axle weight770770820
Permitted roof load757575
Maximum trailer weights (in kg)
Trailer without brakes520520550
Trailer with brakes, gradients up to 8%1,0001,0001,000
Trailer with brakes, gradients up to 12%800800800 212
Page 215 of 240

Technical features
Petrol engine 1.2 51 kW (70 PS) Engine specificationsPower output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm
3
)Fuel
51 (70)/5,400112/3,0003/1,198Super 95 RON a)
/Normal 91 RON b)
a)
Research Octane Number = Anti-detonation rating of the petrol.
b) Slight power loss.
PerformanceIBIZAIBIZA SCIBIZA ST
Top speed (km/h)163 (4)163 (4)163 (4)
Acceleration from 0-80 km/h (seconds)999.4
Acceleration from 0-100 km/h (seconds)13.913.914.6
Weights (in kg)
Gross vehicle weight1,5401,5401,605
Weight in running order (with driver)1,0491,0491,110
Gross front axle weight820820835
Gross rear axle weight770770820
Permitted roof load757575
Maximum trailer weights (in kg)
Trailer without brakes520520550
Trailer with brakes, gradients up to 8%1,0001,0001,000
Trailer with brakes, gradients up to 12%800800800 213
Technical specifications
Advice
Operation
Safety
The essentials
Page 216 of 240

Technical specifications
Petrol engine 1.2 TSI 63 kW (85 PS) Start-Stop Engine specificationsPower output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm
3
)Fuel
63 (85)/4,800160/1,500-3,5004/1,197Super 95 RON a)
/Normal 91 RON b)
a)
Research Octane Number = Anti-detonation rating of the petrol.
b) Slight power loss.
PerformanceIBIZAIBIZA SCIBIZA ST
Top speed (km/h)180 (5)180 (5)180 (5)
Acceleration from 0-80 km/h (seconds)7.47.47.7
Acceleration from 0-100 km/h (seconds)11.311.311.7
Weights (in kg)
Gross vehicle weight1,5701,5701,605
Weight in running order (with driver)1,0951,0951,150
Gross front axle weight870870860
Gross rear axle weight770770820
Permitted roof load757575
Maximum trailer weights (in kg)
Trailer without brakes540540570
Trailer with brakes, gradients up to 8%1,2001,2001,200
Trailer with brakes, gradients up to 12%1,0001,0001,000 214
Page 217 of 240

Technical features
Petrol engine 1.4 63 kW (85 PS) Engine specificationsPower output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm
3
)Fuel
63 (85)/5,000132/3,8004/1,390Super 95 RON a)
/Normal 91 RON b)
a)
Research Octane Number = Anti-detonation rating of the petrol.
b) Slight power loss.
PerformanceIBIZAIBIZA SCIBIZA ST
Top speed (km/h)177 (5)177 (5)177 (5)
Acceleration from 0-80 km/h (seconds)7.67.68
Acceleration from 0-100 km/h (seconds)11.811.812.4
Weights (in kg)
Gross vehicle weight1,5601,5601,605
Weight in running order (with driver)1,0751,0751,130
Gross front axle weight840840835
Gross rear axle weight770770820
Permitted roof load757575
Maximum trailer weights (in kg)
Trailer without brakes530530560
Trailer with brakes, gradients up to 8%1,2001,2001,200
Trailer with brakes, gradients up to 12%1,0001,0001,000 215
Technical specifications
Advice
Operation
Safety
The essentials
Page 218 of 240

Technical specifications
Petrol engine 1.2 TSI 77 kW (105 PS) Engine specificationsPower output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm
3
)Fuel
77 (105)/5,000175/1,550-4,1004/1,197Super 95 RON a)
/Normal 91 RON b)
a)
Research Octane Number = Anti-detonation rating of the petrol.
b) With a slight power loss
PerformanceIBIZA
ManualIBIZA
AutomaticIBIZA SC ManualIBIZA SC
AutomaticIBIZA ST ManualIBIZA ST
Automatic
Top speed (km/h)190 (5)190 (6)190 (5)190 (6)190 (5)190 (6)
Acceleration from 0-80 km/h (seconds)6.56.56.56.56.86.7
Acceleration from 0-100 km/h (seconds)9.89.79.89.710.210
Weights (in kg)
Gross vehicle weight1,5801,5901,5801,5901,6051,640
Weight in running order (with driver)1,0901,1151,0901,1151,1451,165
Gross front axle weight860890860890860880
Gross rear axle weight770770770770820820
Permitted roof load757575757575
Maximum trailer weights (in kg)
Trailer without brakes540550540550570580
Trailer with brakes, gradients up to 8%1,2001,2001,2001,2001,2001,200
Trailer with brakes, gradients up to 12%1,2001,2001,2001,2001,2001,200 216