light Seat Leon 5D 2005 Manual Online

If and when217
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Note
•
Seek professional assistance if the repair of a tyre puncture is not
possible with the sealing compound.
Wheel changePreparation work
What you must do before changing a wheel.– If you have a flat tyre or puncture, park the vehicle as far away from the flow of traffic as possible. Choose a location that is as
level as possible.
– All passengers should leave the vehicle. They should wait in a safe area (for instance behind the roadside crash barrier).
– Switch off the engine. Switch on the hazard warning lights.
–Apply the handbrake firmly.
–Engage the first gear, or put the selector lever to position P for
those vehicles with an automatic gearbox.
– If you are towing a trailer, unhitch it from your vehicle.
–Take the vehicle tools and the spare wheel out of the luggage
compartment.
WARNING
Put the hazard warning lights on and place the warning triangle in position.
This is for your own safety and also warns other road users.
Caution
If you have to change the wheel on a gradient, block the wheel opposite the
wheel being changed by placing a stone or similar object under it to prevent
the vehicle from rolling away.
Note
Please observe legal requirements when doing so.Changing a wheelChange the wheel as described below
– Remove the wheel cover. See ⇒page 218, fig. 146 .
–Slacken the wheel bolts.
– Raise the car wi th the jack in the corresponding zone.
– Take off the wheel and then put on the spare wheel.
– Lower the vehicle.
– Tighten the wheel bolts firmly i n d i a go na l s e q u e n ce wi t h t h e b ox
spanner.
–Replace the cover.
leon_ingles Seite 217 Donnerstag, 20. Oktober 2005 12:14 12

If and when221
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
a large and stable base, if necessary. On a hard, slippery surface (such as
tiles) use a rubber mat or similar to prevent the jack from slipping.
WARNING
•
Take all precautions so that the base of the jack does not slip. Failure to
do so could result in an accident.
•
The vehicle can be damaged if the jack is not applied at the correct
jacking points. There is also a risk of injury since the jack can slip off
suddenly if it is not properly engaged.
Removing and fitting the wheel
For removal and fitting the wheel, the following tasks must be
completed.Change the wheel as described below after loosening the wheel
bolts and raising the vehicle with the jack. Removing a wheel
– Unscrew the bolts using the
hexagonal tool in the handle of the
screwdriver (vehicle tool) and place them on a clean surface
⇒ fig. 150.
Fitting a wheel
– Screw in the wheel bolts and tighten them lightly using the hexagonal socket in the screwdriver handle.
The wheel bolts should be clean and turn easily. Before fitting the spare
wheel, inspect the condition of the wheel and hub mounting surfaces. These
surfaces must be clean before fitting the wheel.
The hexagonal socket in the screwdriver handle makes it easier to turn the
wheel bolts when they are loose. The reversible screwdriver blade should be
removed when the tool is used for this purpose.
If tyres with a specific direction of ro tation are fitted, note the direction of
rotation.
Note
Do not use the hexagonal socket in the screwdriver handle to loosen or
tighten the wheel bolts.
Fig. 150 Wheel change:
Hexagon socket in screw-
driver handle to turn the
wheel bolts after they
have been loosened
leon_ingles Seite 221 Donnerstag, 20. Oktober 2005 12:14 12

If and when223
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Notes for the proper use of the air compressor are included in an additional
instruction leaflet.
WARNING
•
Do not attempt to repair a puncture with the sealing compound if the
tyre has been damaged by driving the car after the tyre has lost its air.
•
Always observe warnings and follow instructions concerning
compressor and sealing compound carefully.
•
Do not drive faster than 80 km/h, avoid heavy acceleration, hard
braking and fast cornering.
•
Tyres which have been repaired with sealing compound are only suit-
able for temporary use over a short period. Therefore, please drive carefully
to the next available qualified workshop.For the sake of the environment
Used sealing compound containers should be disposed of at a proper facility.
Note
Seek professional assistance if the repair of a tyre puncture is not possible
with the sealing compound.Preparation work
Certain steps must be taken before repairing a tyre.– If you have a flat tyre or puncture, park the vehicle as far away
from the flow of traffic as possible.
–Apply the handbrake firmly. – Engage the first gear
, of put the selector lever to position P.
– All passengers should leave the vehicle. They should wait in a
safe area (for instance behind the roadside crash barrier).
– C h e ck w h e t h e r a r e p a i r i s p o s s i b l e u s i n g t h e Ty r e M o b i l i t y S y s t e m “General info rmation and safety notes”.
– Unscrew inflation cap from the affected wheel.
– Take the tyre repair kit out of the luggage compartment.
WARNING
Put the hazard warning lights on and place the warning triangle in position.
This is for your own safety and also warns other road users.
Caution
Take special care if you have to repair a tyre on a gradient.
Note
Please observe legal requirements when doing so.Tyre repair
The following sections describe the procedures for repairing
a tyre.Using the sealing compound
– The instructions on the container give detailed information on
how to use the sealing compound.
leon_ingles Seite 223 Donnerstag, 20. Oktober 2005 12:14 12

If and when225
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Fuse cover underneath the steering wheel
– Switch off the ignition and the component concerned.
– Identify the fuse for the failed component ⇒page 226.
– Take the plastic clip from inside the fuse cover, fit it onto the blown fuse and pull the fuse out.
– Replace the blown fuse (which will have a melted metal strip) with a new fuse of the same ampere rating.
Fuse cover in engine compartment
– Switch off the ignition and the component concerned.
– Prise off the fuse cover in the engine compartment by pressing the tabs towards the centre of the cover ⇒page 224, fig. 153 .
– Identify the fuse for the failed component ⇒page 226.
– Take the plastic clip from inside the fuse cover (at left-hand end of the dash panel), fit it onto the blown fuse and pull the fuse out.
– Replace the blown fuse (which will have a melted metal strip) with a new fuse of the same ampere rating.
– Carefully fit the fuse cover back on to ensure no water can enter the fuse box.The individual electrical circuits are pr otected by fuses. The fuses are located
behind a cover at the left-hand end of the dash panel and on the left-hand
side of the engine compartment.
The electric windows are protected by circuit breakers. These reset automat-
ically after a few seconds when the overload (caused for example by frozen
windows) has been corrected. Colour coding of fuses
WARNING
Never “repair” damaged fuses and never replace them with fuses with a
higher rating. Failure to comply could re
sult in fire. This could also cause
damage to other parts of the electrical system.
Note
•
If a newly replaced fuse blows again after a short time, the electrical
system must be checked by a qualified workshop as soon as possible.
•
If you replace a fuse with a stronger fuse, you could cause damage to
another location in the electrical system.
•
Always keep some spare fuses in the vehicle. These are available from
official Service. Colour
Amperes
light brown 5
red 10
blue 15
yellow 20
natural (white) 25
green 30
orange 40
red 50
white 80
blue 100
grey 150
violet 200
leon_ingles Seite 225 Donnerstag, 20. Oktober 2005 12:14 12

If and when
226Fuses on left side of dash panelFuses
Number Electrical equipment Amperes
1 Diesel and petrol engine control unit 10
2 ABS/ESP control unit 5
3 Airbag control unit 5
4 Heating controls, pressure sensor, heated seats, ESP switch, reverse gear 5
5 Left and right headlamp motor, dimmer, GDL control unit 5
6 Gateway, Automatic gearbox lever 5
7 Windscreen relay, heated mirrors, VDA telephone 5
8 Trailer control unit 5
9 Vacant
10 Vacant
11 Vacant
12 Door control unit (autolock K3) 10
13 Diagnosis, light switch, brake 10
14 Automatic gearbox 5
15 Cable control unit 7,5
16 Heating controls / Air and air conditioning 10
17 Rain sensor 5
18 Automatic gearbox selector lever, parking aid control unit 5
19 Vacant
20 ESP control unit 5
21 D2L engine (20 147 kW) 10
leon_ingles Seite 226 Donnerstag, 20. Oktober 2005 12:14 12

If and when227
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
22
Heater 40
23 Door control unit 30
24 Cigarette lighter 25
25 Cable control unit 25
26 12 V power sockets 30
27 FSI capacity gauge control unit, fuel relay, EKP 1.6 relay 15
28 Comfort system control unit (without autolock 4F8) 25
29 Flowmeter, engine 10
30 Prewired 20
31 Vacuum pump 20
32 Door control unit 30
33 Sunroof 30
34 Comfort system control unit (autolock 4 K3) 25
35 Alarm sensor, horn 5
36 Headlight washer system 20
37 Seats 30
38 Engine 10
39 Automatic gearbox 20
40 Heater 40
41 Tailgate, power 15
42 Cable control unit 15
43 Trailer control unit 15
44 Trailer control unit 20
45 Trailer control unit 15
Number
Electrical equipment Amperes
leon_ingles Seite 227 Donnerstag, 20. Oktober 2005 12:14 12

If and when
228Some of the electrical items listed in the table are only fitted on certain
models or are optional extras. Please note that the above list, while correct at the time of printing, is subject
to alterations. If discrepancies should
occur, please refer to the sticker on the
inside of the fuse cover for the correct information for your model.Fuses layout, engine compartment, left partFuses46
Heating jets, heating controls, air, air conditioning 5
47 Lambda probe 10
48 Lambda probe 10
49 Light switch 7,5
Number
Electrical equipment Amperes
NumberElectrical equipment Amperes
1 Wiper 30
2 Steering column 5
3 Cable control unit 5
4A BS 30
5 AQ gearbox 15
6I nstr u m en t p an el 5
7 Vacant
8R ad io 15
9 Telephone 5
10 Main relay in the FSI / diesel engine compartment / injection module supply
5
Main relay in the engine compartment D2L (2.0 FSI 147 kW) 10
leon_ingles Seite 228 Donnerstag, 20. Oktober 2005 12:14 12

If and when229
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
11
Vacant
12 Gateway 5
13 Petrol injection module supply
25
Diesel injection module supply 30
14 Coil 20
15 Engine T71 / 20 FSI
5
Pump relay 10
16 ADS pump 30
17 Horn 15
18 Vacant
19 Clean 30
20 Vacant
21 Lambda probe 15
22 Brake pedal, speed sensor 5
23 Engine 1.6, main relay (relay n° 100)
5
T 71 diesel EGR 10
2.0 D2L High-pressure fuel pump 15
24 ARF, change valve 10
25 Right lighting 40
26 Left lighting 40
1.6 SLP engine 40
1.9 TDI Glow plug relay 50
28 KL15 40
Number
Electrical equipment Amperes
leon_ingles Seite 229 Donnerstag, 20. Oktober 2005 12:14 12

If and when231
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Bulb changeGeneral notesBefore changing any bulb first turn off the equipment concerned.
Do not touch the bulb glass. Fingerprints vaporise in the heat, causing a
reduction in the bulb life and condensation on the mirror surface, thus
reducing efficiency.
A bulb should only be replaced by one of the same type. The type is inscribed
on the bulb, either on the glass part or on the base.
It is highly recommended to keep a box of spare bulbs in the vehicle. At the
very least, the bulbs that most affect road safety should have spares in the
vehicle.
Main headlights
Dipped beam - H7
Full lights - H1
Front side ligths - W5W
Indicator - PY21W
Xenon headlights
19)
Dipped beam and full lights - D1S
20)
Light burst and additional full lights - H1
Front side lights - W5W
Indicators - PY21W Fog lights
Fog lights - H3
Fixed rear light
Stop/Rear side lights - P21W
21)
Indicator - P21W
Rear tailgate light
Fog light (driver side) - P21W
Reverse gear light (passenger side) - P21W
Rear side lights - W5W
Indicator
Side indicator - W5W
Registration plate light
Registration plate light - C5W
Note
•
Due to the difficulty in accessing the lamps, these must be changed by an
Authorised Service Centre. However, the following is a description of how to
change the bulbs except for the fog lights and interior bulbs.
19)For these type of headlights, the bulbs must be changed by an Authorised Service
Centre, given that complex elements of the vehicle must be removed and that the au-
tomatic control system must be reset.20)Xenon bulbs discharge emit 2.5 times as much light flux and have a useful life five
times greater than halogen bulbs.
21)Electronically controlled single filament bulb for Stop/Side bulbs. If the bulb blows
it will not work or Stop position.
leon_ingles Seite 231 Donnerstag, 20. Oktober 2005 12:14 12

If and when
232Main headlight lamps
Turn signals
Dipped headlights
Main beam headlights
Side lights
Turn sig nal lam ps–Raise the bonnet.
– Rotate the lamp holder ⇒fig. 155 to the left and pull.
– Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Fig. 154 Main headlight
lamps
AAABACAD
Fig. 155 Turn signal
lamps
AA
leon_ingles Seite 232 Donnerstag, 20. Oktober 2005 12:14 12