change wheel Seat Leon 5D 2010 MEDIA SYSTEM 2.2

Introduction
10General operating informationIntroductionDue to changes to its settings, some aspects of the unit's operation may
differ from the descriptions given in this manual. For this reason, SEAT recom-
mends that you reset the unit to its factory settings the first time you use it
⇒ page 87.
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒page 8•Multifunction steering wheel, to change track or station ⇒Booklet
“Owner's Manual”, Section “Vehicle overview” Note
Lightly pressing the buttons or briefly pressing the touchscreen is sufficient
to operate the unit.
Note
Never press a button down for longer than 10 minutes. Otherwise the system
will interpret this as a malfunction ( button jammed).
Note
Due to country-specific legislation, certain functions cannot be selected on
the screen when the vehicle is travelling above a certain speed.
Note
Using a mobile telephone in the vehicle may cause noise from the vehicle
speakers.
Note
In some vehicles equipped with a parking distance warning system, the
volume of the current audio source is automatically lowered when reverse
gear is engaged.
Note
Restrictions on the use of devices using Bluetooth technology may be appli-
cable in some countries. Please ask your local authority for further
information.Switching on and offPress the rotary/push knob
D ⇒ page 8, fig. 1 briefly to manually switch
the unit on or off.
When the system is switched on, the sound source which was playing when
the unit was switched off will come on.
When the engine is off, the unit will automatically switch off after 30 minutes
(timeout).
Anti-theft code
The anti-theft code is stored in the vehicle once it has been entered (conven-
ience radio code). The anti-theft coding lock then only needs to be released
manually if the unit is installed in another vehicle. In such a case, a keypad
field and a prompt to enter the code will appear when the unit is switched on.
In this case, you should contact a SEAT dealer.
If the vehicle battery has been disconnected, switch on the ignition before re-
connecting the unit.
A1
MediaSystem2.1_EN.book Seite 10 Donnerstag, 29. April 2010 4:18 16

Introduction11
Adjusting the base volumeChanges to the volume are indicated by a “bar” on the screen. During this
time the unit cannot be operated.
At “0” the unit is muted (display:
) and the current media source is
stopped.
It is possible to preset certain volume settings and adjustments ⇒ page 87.
WARNING
Your attention may be distracted from the traffic if you use the radio and
navigation system while driving, resulting in accident.•You should always drive with due care and attention.•Select volume settings that allow you to easily hear signals from
outside the vehicle at all times (e.g. emergency service sirens).•If the volume is too high, you could damage your hearing. Even if the
volume is too loud for a short period only.Caution
If the volume is too high or the sound is distorted, the vehicle speakers may
be damaged.
Note
If the base volume has been turned up high to play an audio source (e.g. due
to very quiet audio output from an external audio source), lower the volume
again before switching audio source.Additional information and display optionsThe text displayed on the screen may vary depending on the settings and may
not match the illustrations shown here.
All displays appear only after the radio-navigation system has completed
start-up.
Depending on the vehicle, the changes to the air conditioning settings or the
texts relating to driver assistance systems fitted at the factory are displayed.
These displays disappear automatically when they are no longer required.
Function
Action
Increase the vol-
ume.
Turn the sound control knob
D ⇒ page 8, fig. 1 to the
right, or press the button on the multifunction steer-
ing wheel ⇒Booklet “Owner's Manual”.
Lower the vol-
ume.
Turn the volume control
D anti-clockwise
or press the button on the multifunction steering
wheel.

MediaSystem2.1_EN.book Seite 11 Donnerstag, 29. April 2010 4:18 16