light SKODA 105S 1980 Owner's Manual

r 2.1-t 2.3
I
I I
I
Dissssembly
ond
Reossembly of Pedols
This is usuolly not necessory. The pedols
con
be disossembled ofter removing the oxiol screw
in the pedol
pin
ond slipping off the return
spring. Do not remove the switches if it is not
obsolutely necessory -
see odiustment. On re-
ossembly, lubricote
the pedol
bush with lubri-
coting greose
of the some brond os used for the
steering linkoge -
see Chopter 7.5, por.3.
Pedol Free Trovel
Adiustment
Adjust the free
trovel of pedols
ossembled
with moster cylinders so thot the pedol piston
rod hos o
cleoronce of 0.5
to 1mm
when beoring
ogoinst the piston
heods of the
moster cylin-
ders. The free trovel of the pedol pod
should be
from 3 to 5 mm. lt
con be odiusted by rototing
the eccentric pin
on the pedol
brocket -
see
Fi9.12.111.
For the odjustment of the broke pedol
with
broke booster ond/or levelling of the broke
pedol with the
clutch pedol,
see Chopter 9.6 -
Ad justment.
Adiustment of Switches The switches con be
moved in
the ellipticol
holes of the brocket ofter loosening the fosten-
ing copscrews with ploin
woshers under their
heods. A pocking piece
should be slipped
under
the switch of the broke pedol
trovel worning
light ond the powl
of the switch pin
should be
held down under the fostening copscrew.
Ad just
the stop-light switch
so thot it
switches on the stop lights ot o pedol
trovel
of 10 to 15 mm meosured on the centre of the
pedol pod.
Adiust the pedol
trovel signolling switch so
thot the pushed-in
side push-button
pin
is
re,ecsed ot o pedol
trovel of 100 to 110 mm
mecsured on
the centre of the pedol
pod.
Press
the push
button into
the switch ofter hoving
completed the
odiustment.
12.2 ACCELERATOR PEDAL AND CABLE
The occelerotor pedol
forms o unit with its
self-lubricoting beoring ond the lever.
lt is
bolted to the f
loor tunnel. A coble possing
through the tunnel is ottoched to the pedol
lever ond the reloy
lever on the engine by
meons of clomps- The coble is protected
by
o Bowden tubing.
Pedol Removing ond Refitting
1. Loosen the clomp holding the coble on the
engine-mounted reloy lever. 2.
Remove the copscrews holding
down the
becrring with the pedol,
depress lightly the
pedol, ond lift it out of the f loor
tunnel together
with the beoring. 3. Disconnect the pedol
from the coble ofter
ioosening the clomp.
Removol ond Refitting of Bowden Tubing
ond Cqble
The Bowden tubing is
fostened to
the brocket
irr the floor tunnel by
meons of circlips. After
their removol, pull
the Bowden tubing inside
the cor. On ref
itting the tubing, lubricote it with
o low-viscosity oil (of
the SAE 20
closs). lt hos
been lubricoted with greose
in the foctory.
Fit
the clonrps so thot their longer ports (from
the
screw to their end) ore on the side of the
I evers.
Accelerotor Coble Adiustment
Adjust the coble so
thot it is not
excessively
tensioned or too slock. Loosen the clomps on
the engine side of the coble, move slightly
the
clomp toword the reloy lever,
ond tighten the
screws of the clomp.
12.3 GEAR SHIFT LEVER
AND LINKAGE
The geor shift mechonism consists of two
units: the geor
lever with its housing ond oc-
cessories, ond the geor
shifter rod
ond the
shifter lirrk with joint
(ot the georbox)
for
domping the vibrotion of the power
pock
tronsnritted to the geor
lever.
Removing Geor Lever
Housing ond Link
1. Lift owoy the mot from the floor tunnel in
the front ond reor comportment. lf seporote,
remove the individuol floor mots ofter hoving
prised out their clips with o screwdriver or
o similor tool. lf o one-piece floor
covering is
used, remove the door sill strips
on one side,
tip the seot, ond bend over the
floor covering.
2. Remove the geor
lever housing copscrews
ond prise
out the lid (next
to the clip) between
the seots. Proceed through the
operture to dls-
connect the bolted connection of the link with
the housing shifter rod.
3. Lift
owoy the housing with the lever
through the operture. Swivel the lever so thot
the shifter rod
does not protrude
over the
housing beoring thus obstructiong the removol.
4. Usuolly it is not necessory to remove the
geor shift link from
the cor. lf
obsolutely necess-
ory, the link con be
disconnected only ofter
162

'i
iiiI 14. Fuse box
Centrol connection of conductors -
do not
seporote them from the bunch!
15. Direction indicotor switches, dip switch,
and horn switch
eight-pole terminol
boord
six-pole terminol boord
16. Porking light switch ond high beom feeder four-pole terminol boord
17. Switch box femole connectors 5.5 with symbols "15",
"30", ond '50"
to be
connected to symbols
"15u, "30', ond '50"
on the switch box
18. Instrument ponel
ten-pole terminol boord
six-pole terminol boord
eorthing coble with lug
'19. Heoter switch
four-pole terminol boord
20. Switch of disobility lights
six-pole terminol boord
21. Door switch, right-hond
green -
femole connector 5.5
22. Dome light,
right-hond
green -
femole connector 5.5
red -
femole connector 5.5
23. Stop switches
forked (yellow) -
femole connectors 5.5 .
red -
femole connector 5.5
white -
femole connector 5.5upper ond lower
switch
upper switch lower switch
24.Fuel gouge block -
femole connector 5.5
yellow -
femole connector 5.5
blue -
femole connector 5.5
to be connected to the respective pins
(blodes) of the some colour of the fuel gouge
25. Storter motor, reversing
lomp switch
conductors with lugs stater motor moin
terminol boord
storter motor
control switch
green -
femole connectors 5.5 heodlomp switch
26. Oil pressure
gouge,
thermometer, corburettor
iet seporotor
green -
femole connector 5.5 yellow
-
femole connector 5.5
green - telethermometer
primory element
femole connector 7.
corburettor
iet seporotor
27. lgnition coil, voltoge regulotor, olternotor,
tochometer
conductor with femole connector ond
bronching lug
femole connector-regulotor terminol 15/54
lug -
ignition coil terminol 15
blue -
femole connector 5.5,
symbol "R"
. regulotor terminol "R"
yellow -
femole connector 5.5,
symbol "M"
regulotor terminol "M"
blue -
connector "R"
. olternotor terminol "R"
yellow -
connector "M".
olternotor terminol "M"
lug terminol "+B"
conductor with
lug ignition coilterminol "1"
(tochometer operotion
)
28. Toil lomp cluster, right.hond
yellow -
femole connector 5.5 toil light
block -
femole connector 5.5 direction indicotors
red -
femole connector 5.5 stop light
green -
femole connector 5.5 reversing lomp
29. Licence plote light
conductors with femole connectors 5.5
30. Toil lomp cluster, left.hond
se point
28.
b) Connection
of free conductors
1. Storoge bottery
bottery coble positive
(*)
terminol -
storter motor
bottery eorthing strip negotive (-)
terminal -
bodywork (eorthing conductor)
2. Engine engine eorthing strip (fostening
lug) -
engine cross beorer (eorthing conductor)
3. Distributor speciol coble from distributor to
ignition
coil; end with interference suppressing
terminol to distributor
coble from distributor to ignition coil
terminol "1"
cylindricol
(pin)
connector
pressure gouge172

I
I
I
s
I
I
I
t
(
(
t
l
,
t
T c
R
L D
v Ir
1' 2
3
orotely
(
screen the other one) . With lef t
directionol heodlomps,
the borderline deviotes
towords the other
side.
lf the heodlomps ore neorer to the woll thon
the soid
5 metres, decreose the meosure indi-
coting the
deviotion of the light ond
dorkness
bordeiline from the
height of the heodlomps
obove the ground in the
direct proportion to
the
decreose of
tfre distonce, for
exomple when
plocing the cor 2.5 metres
from the woll, de-
creose the deviotion bY holf.
Light proiections "A"
ond "B"
correspond to
the spocing of heodlomPs on
the cor ond they
hove the following dimensions:
Heodlomps, dio. 160
mm 1,030
mm
Duol heodlomps, dio.
130 mm 1,114
mm
Auxiliory heodlomps, dio.
130 mm 790 mm
When odjusting the heodlomps, the cor must
be empty ond the
tyres must be correctly in-
floted. Hologen heodlomps should
not be left
switched on for too long o period os they build
up heot if not cooled by heod-on
oir blost when
driving. For lhe odiustment of
heodlomPs ore intended
screws in their fromes. The screws
ore occess'
ible ofter the removol of the side ports
of the
grille. Remove the copscrews of the corners
ond push
the grille
oside.
Heodlomp Assembly
o) The fundomentol fostening
Port of
circulor
heodlomps is the
so-colled support plote
(rec-
tongulor plote)
ottoched to the bodywork by
copscrews with lock woshers. The
heodlomp
housing is bolted to this suPPort plote by bolts
with nuts ond lock woshers. One of the bolts holds
down olso the
lug of the eorthing coble-
The inner frome,
forming the
odiusting element
of the heodlomp insert, is ottoched
to the
hous'
ing by two speciol odiusting screws
ond two
tension springs. The heodlomp insert
is ot'
toched to
the bezel by
three copscrews.
There is one left-hond ond
one right-hond
support plote.
Both should
be mounted with the
oriow ond the word "TOP"
upwords. With
the
exception of the ouxiliory heodlomps, the
heod'
lomp inserts ore different for
the left-hond ond
the right-hond troffic. The leods
enter the hous-
ing through o
rubber grommet.
When r-eplocing the insert, remove
the bezel
copscrews. After
hoving fitted o new insert, it
is necessory to reodiust the
heodlomps.
Front Direction Indicotors
The right-hond ond
left-hond direction indi-
cotors ore undisossembloble units
(the
lomp
fostening sockets (locks) ore
mounted in the
direction towords the cor longitudinol centre
line). They ore fostened to their brockets in the
bumper with o nut ond o ploin ond
o lock
wosher.
Toil Lomp Cluster
The lomp cluster is on undisossembloble unit
fostened to
the bodywork by
nuts with ploin
woshers ond the
respective bolts.
Scrope off
the enomel ot the
top bolt used for holding
down the eorthing coble.
For the sequence
of the individuol lomps ond
their bulbs see Fig. 13.111 ond the respective
porogroph on bulbs.
Fig. 13.812 -
Adiusting ond
Fastening Screws of Right-hond Heodlomps -
their locotion
on
left-hond he-odlomps is their
mirror ref lection
1 -
Sidewoys odiusting screw
2 -
Height odiusting screw
3 -
Fostening screws
182

1 3.9-1
3.10
13.9 HORN
It is situoted behind
the left'hond port of
the
front bumper. To
remove it, disconnect the
leods ond remove the
fostening screw. heor
the ormoture being ottrocted (o
cleor ond
loud click). Now continue to
switch the bottery
on ond off
while rototing
corefully ond
sloryly
the screw "1"
onticlockwGe till
the
horn sounds'
iune it by rototing the odiusting.:cr9ry slightly
clockwise or
bock.-After hoving
odiusted (tuned)
ih" honn, secure
oll
odiusting ports with
o
dob
of point.
12
volts
4 omperes
Operoting
voltoge
Moximum current demond
Horn Adiustment
Before odiusting (tuning) the
horn, clomp it
firmly by th'e brocket ond
tighten thoroughly
oll screws "4"
ioining the
horn cover
with the
housing ond the dioPhrogm.
1. The horn is "hoorse"
- Using o screwdriver
rotote slowly the screw "1"
clockwise to odiust
the current demond
till the tone is cleor.
2. The horn sounds weokly -
Using o screw-
driver, rotote the screw "1"
slowly onticlockwise
to decreose the current demond
till the tone is
loud ond cleor.
3. The horn does not sound ot oll-Proceeding
through the operture in the front cover, loosen
the nut "2"
using o socket
sPonner. Then
insert
o screwdriver ond rotote
the odiusting screw
clockwise till it
beors lightly on the core. Then
bock off the screw by 1lz
or moximolly 3/a
of
o turn to odiust the distonce
of the ormoture
from the core. Hold the screw in this position
with the screwdriver ond
tighten firmly the nut
by rototing it clockwise. After hoving
connected
the bottery (of
the specified voltoge), you
will Fig.
13.9/1 -
Sectionol View
of Horn ond
o View
of Reor
Adiusting Screw
13.10 STARTER MOTOR
This is o series motor for
intermittent oper-
otion with on
electromogneticolly engoged
pinion. -@
c@c
Specif icotions
TyPe Roted outputStorting torqueSpeed for roted output
Voltoge ocross terminol
No-lood storting current
Direction of rototion
Number of pinion
teeth/modulus .
Contoct spring pressure PAL-Mogneton
12 V/0.8
h.
p. -
443'115'142'070
0.66 kw (0.e h.
P.)
12.25 Nm (1.25
kgm)
'1,000 r. p.
m. moximum
9.5 V moximum
65 A moximum
onticlockwise (left'hond)
912.5
e.3 N (0.ss0 ks) +100/6
"30"
of roted output
Mointenonce The mointenonce consists of periodicol
in'
spections ond repoirs or replocement of foulty
ports:
o) brushes
b) brush springs
c) commutotord) storter pinion ond idler
e) self-lubricoting beorings The brushes
must
be sufficiently long
ond
they must slide
freely in
their-cells, their
press-
ure springs must hove o
sufficient thrust,
the
commutotor must not
show ony
domoge, ond
it
must be
free of dust ond dirt.
Cleon the
commu-
totor with olcohol, petrol or
trichloroethylene,
ond let it dry before closing it
ond switching
on the storter motor. A
burnt or mechonicolly
domoged commutotor must
be repoired or
re'
ploceJ immediotely. A commutotor in
good con'
dition hos o brownish red
hue.
184

(
1
z
Strike the
slip-over ring off the circlip
(towords the motor windlng). Open the circlip
ond pull
it off the shoft together with the re-
leosed ports.
8. lf necessory, re-turn the commutotor ond
scrope or mill out the insulotion between the
lominotions. "Mikonit"
should be 0.4 to 0.8 mm
below the octive surfoce.
Note: The
switch connot be further token
opat. lf
defective, lt hcs to be reploced with
o new one. When cleoning ports
of the storter
motor, do not dip the ormoture or the pinion
with the idler into petrol
or onother degreosing
ogent.The some opplles to the end shieldswith
beorings. By dipping them in o degreosing
ogent, the beorings become procticolly
worth-
less"
Storter Motor Reossembly 1. Lubricote the hellx of the ormoture shoft
with greose -
see Chopter 15.2 'Lubriconts
of
foreing mokeu ond fit the pinion
with the idler
ond the slip-over ring in posltion.
Fit the
circlip
into the groove
in the shoft, ond drive the slip-
on ring over it. The pinion
with the idler must
move freely olong the shoft.
2. Slip the respective
woshers on the shoft in
their originol sequence (corrier
ring, distonce
ring, fibre ring, distonce ring) ond insert the
ormoture with the engoging lever
into the drive
end shield. 3. Suspend the switch
ormoture into the
pre-engoging lever ond bolt down the switch
lightly. Fit the lever pin
into the drive
end
shield ond lock it in position
with the retoiner.
4. Tighten the copscrews of the switch
ond
fit the stotor on the drive
end shield.
5. Instoll the respective
woshers into
the
commutotor end shield in
their originol se-
quence (the dished wosher with its centre
focing the shield, then the ploin
wosher, the
toothed wosher, ond the drive wosher).
6. Fit the commutotor end shield with lifted
brushes on the shoft (in
the position
occording
to the recess
for the excitotion outlet ond the
notch) ond screw in the clomping bolts.
7. Instoll the brush interconnecting strip ond
bolt it down together with the field winding
outlets to the positive
brush holders, lower the
brushes. 8. Fit the Insuloting strip in position
ond bolt
down the cover. 9. Test the storter mottr.
Diognosing Storter Motor Defects in Cor
o) lf the storter motor refuses
to operote, look
first for on interrupted connection between
the bottery ond
the storter
motor, the engine
eorthing ond the storter
motor, or the engine
eorthing ond the bottery. lf these connec-
tions ore in order (current
flows to the ter' DK
1575
Fig. 13.10/3 -
Storter Motor Testlng Connection
minols u30"
ond "50"
with switched on
ignition), stort looking for o foilure of the
storter motor switch. Even in this instonce,
the couse con be o fully dischorged or foulty
bottery.
b) lf the storter motor
continues running
even
ofter the ignition key hos been switched in
the switch box from the position "START",
it hos to be stopped without ony deloy by
disconnecting the bottery (using
its eorthed
pole).
c) lf the storter motor hos no power
to cronk
the engine, stort with switched-on heod-
lights. A
morked dimming indicotes c poorly
chorged bottery.
Tentotive Checking of
Storter Motor
Outside Cor
Connect the terminol "30'of
the storter
motor to o properly
chorged bottery ond incor'
porote on ommeter with o wide
meosuring ronge
into the circuit -
see Fig. 13.10/3.
Stort the
engine (feed
current to the terminol "50").
The
volue of the current ot idling speed must
not
exceed 65 omperes (not
considering the peok
ot
the first momentous deflection).
The storter motor must run noiselessly,
smoothly, ond the pinion
must move smoothly
into ond out of the rest position
(engoge
ond
diesengoge). The engoged pinion
must not ro-
tote direct on the foce of the slip-on ring. The
run-out of the storter motor must not lost longer
thon 8 seconds ofter the disconnection of the
switch from the current supply.
Inspect the brush pressure
springs. The
brushes must
beor on the commutotor by ot
leost two thirds of their surfoce ond they must
move freely in their cells.
The ormoture should hove o noticeoble oxiol
cleoronce (ploy)
not exceeding 0.7 mm.
At
o slight rototion of the pinion
in the direction
of the storter motor rototion,
the idlor must
slip
freely.
186

t3.tt-l
3, I 5
I 2.
Remove the clomping
bolt from the brocket
ond lift owoy the motor.
3. Remove the other clomping
bolt from the
motor, lift owoy the stotor ond the
brush
springs, ond push
out the brushes. The
other
motor ports
connot be dissosembled.
Reossembly of Motor ond lmpeller
1. lnstoll the stotor with the slot focing
the
bosses on the frome ond with its index line
focing the line on the frome,
ond fosten
the
ports with screws ond woshers.
2. Instoll the brushes ond brush springs,
suitobly orch the brush cobles so
thot they do
not obstruct the movement of the brushes ond
so thot they connot
couse o short-circuit.
3. Top the stotor lightly with o soft
mollet
to settle it in
the beorings, ond lubricote
the
beorings. 4. Connect the motor to the power
supply
ond test briefly its running ond direction
of
rototion. lf it rototes in the opposite direction,
rotote the frome
ossembly through 180'.
5. Remove the clomping bolt of the motor on
the terminol boord side, instoll the motor in
the brocket, ond lock it in position
with the
bolt ond wosher.
6. Fit the spring on the motor shoft,
support
the shoft
to ovoid domoging the beorings, ond
press-on the impeller. The cleoronce between
the impeller circumference ond the brocket
must be smoll,
obout 1.5 to 2
mm. Lock the im-
peller in position
by pressing -
on the lock ring
- ogoin the motor shoft
must be supported.
7. Close the motor beoring from obove by
fitting the cover.
13.14 WINDSCREEN WASHER
Technicol Description
The windscreen wosher is o unit comprising
o reservoir, o pump
with motor, o distributor
volve,two nozzles, ond the connecting pipeline.
Windscreen wosher type MEZ MM 2004
Roted voltoge
Roted input .
Pump dischorge,
minimum .
12 volts
. 50 wotts
. 15 c. c. ot o pressure
of 10 MPo
(1 kg/cme)
Fitting, Removol, ond
Adiustment
The reservoir is held in
its ploce
by o cover
bond secured by copscrews with flot woshers.
The motor with pump
is bolted down, using
flot woshers under the copscrews. The suction
bronch socket is smooth, thot of
the dischorge Fig.
13.1a11- Windscreen Wosher
1 -
Reservoir, 2-
Sproying nozzles, 3- Motor
with pump
bronch reinforced with o collor; the positive
pole is connected to the suction side, the
negotive pole
to the dischorge side
(when
viewing the cor from the front, suction is
on
the right-hond side, the dischorge on the left"
hond side).
The distributor volve
is fostened by o cop-
screw, the distribution pipeline
being simply
fitted on it. The nozzles (heods
with nozzles) ore se-
cured in position
by pressing
them down from
obove into bushings
inserted into the cor body
by their necks. To
odjust the required direction
of the woter streom,
turn the nozzles to
the
respective ongle using o needle inserted into
the nozzle hole.
Fil!ing the Reservoir Open the reservoir by turning its
cop onti-
clockwise. In
summer, fill it with woter or
o mix-
ture of woter ond one of the odditives for
wind-
screen woshers ovoiloble on the morket, ond in
winter exclusivelywith on ontifreeze of o brond
intended speciolly for windscreen woshers -
never use on ontif reeze
intended for motor
vehicle cooling systems. Be coreful if
the body finish is touched up
with other thon boking enomel. Additives in
the woter ond other
liquids, usuolly contoining
spirit, ore opt to leove
unremovoble spots on
the enomel. Use only woter when testing the
windscreen wosher.
13.15 INSTRUMENT
PANEL
Technicol Description
The instrument ponel
contoins oll meosuring
instruments ond indicotors recommended by
192

1 3.1 6-t 3.1
7
focio ofter removing two
copscrews ol-l the
ponel bottom. lt moy
be olso necessory to pull
off the heoter control push
buttons.
c) Switch of disobility worning lights
For fostening see
informotion sub
b). -l
he
switch operotes only
when connected to the
direction indicotor ticker.
d) Dipswitch, direction indicotor, horn, wind-
screen wiper, ond winscreen wosher switch
ox 1568
instolled on
the steering
fostened to
the reduction
with shoft
beorings ond to
steering wheel shoft
shroud.
Fig.
13.16/1 -
Switch Box with Steering Lock -
the orrows indicote the copscrews (M
3.5)
holding down the switch box in the steering
lock housing
disengoging the shoft from
the bodywork -
see
Chopter 7.8, porogrophs
1 to 5 -
without, how-
ever, disengoging the shoft from
the steering
box. The switch box con be removed
ofter loosen-
ing two copscrews on the steering lock hous-
ing (see
illustrotion).
Reverse this procedure
when refitting the
switch box. Turn
the key ond
the key hole of
the switch box into the left-hond extreme pos-
ition (STOP),
instoll the switch box in the
steering lock,tighten the copscrews ond secure
them with o dob of point.
13.17 SWITCHES OF LAMPS
AND WARNING
SYSTEMS, DIRECTION INDICATOR
TICKER, RECEPTACLE
For the wiring of these electricol devices
refer to Chopter 13.1 -
Electricol Equipment
Connections ond Wiring Diogrom -
ond for
their operotion to Chopter 1.3.
All the devices ore expendoble ond they hove
to be reploced with new units if defective.
All the switches ore of the contoct type,
speciol types ond exceptionol connections ore
mentioned in the following text.
o) Switch of porking
lights ond heodlights
(feeder of chonge-over
switch
of these
lights)
The switclr is fostened to the instrument
ponel by o nut with o wosher under the push
button. When instolling the switch,
turn it so
thot it engoges in the locking slots. The push
button con be removed
by pulling
it off ond
refitted bv pressing
it down.
b) Heoter switch
This is fostened in the some monner
os the
switch sub o). Access to the switch
body con
be goined
by removing the centre ponel
of the This switch
is
column shoft ond
sleeve of the tube
the top port
of the
Removol: Remove the steering wheel
ond the bottom
port of the shroud -
see Chopter 7.8.
The switch
con be releosed from the shoft ofter loosening
the screw in the driver ond the removol of the
driver (
if the switch is equipped with
such
driver), ond the loosening of the
screw in the
yoke on the switch bottom right-hond side.
Loosen or remove the fostening screws of
the
shroud ond lift owoy the top port
of the shroud-
lf you
intend to remove olso the
steering
geor, do not loosen the screw
on the switch
bottom right-hond side but the screw on the
left-hond side, ond lift
owoy the switch
together with the reducit-tg
sleeve on the steer-
ing wheel shoft tube.
Refitting ond Adiustment
Reverse the described procedure when
re-
fitting the switch. lf the cor is equipped with
:" outomotic
direction
indicotor concelling
Fig. 13.1711- Adiusting Elements of
Directiorr
lndicotor Self-concelling Device
1 -
Centering pin
of the left-hond
switch or
mork on the switch foce, 2 -
Boss on the bush
foce, 3 -
Driver
194

13.18 FOG
LAMPS AND
OTHER OPTIONAL
EQUIPMENT
Fog lomps
The fog lomps ore optionol equipment. When
f itting them on the cor, refer to the wiring dio-
grom while observing notionol regulotions (in-
ternotionol regulotions
hove not yet
been uni-
fied os for os individuol requirements ore
con-
cerned) ond the following informotion. In
Czechoslovokio, the Decree
No.100/1975 of the
Book of Stotutes, porogroph
51, is opplicoble. Switching
reloy
Use o switching reloy of the some design
os
for the ouxiliory heodlomps (on
cors with twin
heodlomps) or onother reloy operoting in the
some woy. Any ploce
con be chosen for its
in-
corporotion into the circuit.
Cobles For worning lomps ond the reloy
switching
circuit use cobles with o section of 0.75 mm2,
for the remoining electricol equipment 1.5 mm2
section cobles.
R,ELAY SWITCHING OF HEADLAMPS
Optionol equipment moy include on incorpor-
crted reloy for switching in the heodlomps. In
some countries (for
exomple Sweden), this
reloy is required by regulotions. For the re-
spective connections see the following wiring
diogrom.
1L7 1L7a DK 1582
Fig. 13.1812 -
Wiring Diogrom of Heodlomps
Using Switching Reloy -
odditionol incorpor-
otion into the bosic electricol equipment
( Fi9. 13.1/1)
147 -
Reloy of moin heodlomps
147o- Reloy of ouxiliory heodlomps
Heated Rear Window (1979
on)
Circuit Divide into two sections.
1. Heater switch with five positions from
left
to right. a) Heated screen b) off c) High speed
fan d) Slow speed fan e) Slow speed and
heated screen. 2. Power supply.
;;---A.i'
t..[9-+'--'o
B
A
ll
Y
5-
r369
Fig. 13.18i 1 -
Wiring Diogrom of Fog Lontps
1- Switch, 2-Fog lomps, 3- Worning lomp,
4 -
Switching reloy (A -
reloy closing circuit,
B -
fog lomps feeding circuit), 5 -
Fuse No.1 of
cor electricol equipment, 6 -
Fuse No. 4 of cor
electricol equipment, 7 -
Fuse No. 7 of cor
electricol equipment, 8 -
Fog toil light, I -
Switch of fog toil light, 10 -
Wcrning lomp
Switches Instoll them on the ouxiliory ponel
(stondord
port of the
cor) under the focio. Use
the switch
with the built-in worning lomp for the toil light.
Worning lomps Use the unconnected green
wo,rning lomp in
the instrument ponel
for fog lomps; the worning
lomp oppertoining to the toil light
is built-in
in the switch.
I
I
I
l';
196

1 t.1
-1
4.3
surfoces ore
sproyed with o
Protective com'
pound. The floor boords including the floor of
the boot ore covered with textile corpets while
rubber mots ore used in Skodo 105 S.
The in-
terior luggoge comportment is
lined with insu-
loting felt
sheet.
fne body finish consists of severol loyers of
speciol onti-corrosive cootings, o primer
coot,
ond o synthetic boking enomel top
coot in
colours complying with
o speciol specificotion.
14.1 BUMPERS
To Remove Front BumPer
Disconnect the
leods of the horn ond front
direction indicotors. Remove bolts connecting
the side sections of
the bumper with the wings
ond bolts of the bumper brockets, connecting
them to the wheel splosh guords. Now
the
entire bumper is free ond it con be removed.
Te Remove Reor BumPer
Proceed in the some woy with the exception
thot there ore no leods to be disconnected.
To Remove Overriders
Screw off the nut M 10 ond lift owoy the
overri der.
14.2 WTNGS
To Remove Front Wing
First remove the front bumper (see
Chop-
ter 14.1), the front door (see
Chopter 14.5), ond,
in the cose of the left-hond wing, the boot lid
Fig. 14.211- Removing Front Wing -
orrows
indicote fostening points (see
Chopter 14.3). lf the door sill is covered
with o trim moulding, loosen this moulding
portiolly. Now remove the bolts fostening the wing to
the bodywork under the sill (from
underneoth),
on the side edge of the body post,
in the chon'
nel next to the boot, ond in the forebody under
the heodlomp.
To Reinstqll Front Wing
lf the seol strip in the front
Port of the wing
is domoged, reploce it with o new one, ond
stick it on if it hos got
unstuck. Pock olwoys
o new seoling strip between the wing edge ond
the body fromework. Then instoll
the wing in
position ond locote it by tightening slightly the
connecting (fostening) bolts.
Do not tighten
the bolts firmly before hoving fitted properly
the wing.
14.3 BONNET AND BOOT LID
Removing Boot Lid
Remove the nut ond bolt of the strut ond
the screws fostening the
hinges, ond lift owoy
the complete lid.
Removing Engine Bonnet
Slip the bonnet strut out of
its guide,
screw
off the nuts of the hinge fostening bolts, ond
lift owoy the bonnet.
Reinstollotion ond Adiustment of Boot Lid
ond Engine Bonnet
Instoll the lid (or
bonnet) over
the luggoge
(or engine) comportment ond
tighten lightly
the bolts ond/or the nuts of the hinge bolts.
Moke the lid (or
bonnet) fit perfectly
with the
edges of the bodywork by shifting the hinges
in their respective holes
os necessory, ond
tighten fost the bolts ond/or nuts of the hinges-
Assemble the strut of the boot lid.
Boot Lid Releose Rod ond Engine Bonnet
Releose Coble
The releose rod of the boot lid (Fig.
1.3113)
is connected with the reloy link by meons of
o pin
ond forms on ossembly unit with the lid
locks. The
hondle of the releose rod con be
removed ofter pushing
out the pin.
The entire
ossembly con be lifted owoy ofter removing the
lid locks.
Reverse this procedure
to reinstoll the os'
sembly. Tighten the bolts of the locks lightly
ond fit the lid properly
in positlon.
Now odiust
202 c
o
o
o ir
e
tt d

I-
.'t Fig.
15.3/3 -
Oil Filter
oil f ilter bowl
witlr f ilter
element
centre-boll oil pressure
switclr pressure
oir. When driving often
on dusty roods,
ihe cleoning intervols
should
be shortened by
holf. For oir cleoner mointenonce in tropicol
re'
gions refer to
ChoPter 16.2.
Air Cleoner -
winter oPerotion
Remove the rubber
cop from
the cover exten-
sion orm ond
use it to stop the mouth of
the
orm. Fit o guide extension into
the cleored hole
in the ornr ond
insert the
corrugoted poper hose
(included in the
cor equipment) into
the
ex-
iension ond
the holder on the
intoke ond
ex-
houst monifold.
Give the
hose the required shope by
bending
it slowly ond corefully. Above
oll, ploce
it into
the holcier so thot
there is
o suff icient distonce
(wide enough to
insert o
finger) between it
crnd the exhot-tst monifold.
Tightening of
cYlinder heod bolts
The cylinder heod
bolts should be tightened
in the running-in period before
the gosket gets
settled ond then
ofter every replocement of the
gosket, i.e., ofter
obout 1,000
kilometres' For
itre tightening procedure,
s9e
Chopter
-2'16'
Check'ilg of vilve
cleoronce ofter
every tighten'
ing of tlie
cylinder heod
is o
routine procedure
which must not be omitted.
Volve Cleoronce
For checking procedures
ond odiusting volues,
refer to ChoPter 2.13.
Alternotor V'belt
Tensioning
Loosen the
nuts of the bolts
in the olternotor
f longe (fostening
it to
the engine ond
the strut)
ond'of itre
bottJ holding down
the strut on
the
olternotor, ond
swing
oside (tip)
the olternotor'
Adiust the
belt so
thot it gives
woy 10- to
15 mm midwoy between the
belt pulleys
when
depressed lightly (ot
if o- weight of obout
2 kg were opplieal with
the
finger ot this point'
LoCk the
olternotor in
this position
by tighten-
ing properlY
oll the nuts.
Belt dimensions: 9x9.5x1,0O0 mm.
To Cleon the
Distributor
The contoct breoker points, the
cover, ond
the rotor orm
of the distributor must never
be
greosy or dirty. Scrope off
ony burns on the
distributor cover.
lf you hove
cleoned the
distributor with
oetrol, do
not ref it the cover till ofter
the petrol
hos comPletelY evoPoroted.
222
oll
the greose
into the beorings. Tighten
the
cop thoioughly so
thot it connot be worked
loose by vibrotion.
Air Cleoner -
cleoning ond
replocing of
filter
element
Unclosp the cover
fostening clips
and lift
owoy the lid. Depress the
cross broce in
the
1ock6t, rotote
it
slightly to disengoge it, ond
withdrow the filter
element. Wipe
cleon the
inside of the
iocket, cleon
the filter
element or
reploce it with o new
one, ond reclose the oir
cleoner proceeding
in reverse order.
Shoke ond
top the filtet element to
rid it of
clirt porticles, oncl
blow it off ond through with
Fiq.15314
-
Lubricotor of
Woter Pump Beorings