oil viscosity SKODA 120 LS 1980 Workshop Manual

r 2.1-t 2.3
I
I I
I
Dissssembly
ond
Reossembly of Pedols
This is usuolly not necessory. The pedols
con
be disossembled ofter removing the oxiol screw
in the pedol
pin
ond slipping off the return
spring. Do not remove the switches if it is not
obsolutely necessory -
see odiustment. On re-
ossembly, lubricote
the pedol
bush with lubri-
coting greose
of the some brond os used for the
steering linkoge -
see Chopter 7.5, por.3.
Pedol Free Trovel
Adiustment
Adjust the free
trovel of pedols
ossembled
with moster cylinders so thot the pedol piston
rod hos o
cleoronce of 0.5
to 1mm
when beoring
ogoinst the piston
heods of the
moster cylin-
ders. The free trovel of the pedol pod
should be
from 3 to 5 mm. lt
con be odiusted by rototing
the eccentric pin
on the pedol
brocket -
see
Fi9.12.111.
For the odjustment of the broke pedol
with
broke booster ond/or levelling of the broke
pedol with the
clutch pedol,
see Chopter 9.6 -
Ad justment.
Adiustment of Switches The switches con be
moved in
the ellipticol
holes of the brocket ofter loosening the fosten-
ing copscrews with ploin
woshers under their
heods. A pocking piece
should be slipped
under
the switch of the broke pedol
trovel worning
light ond the powl
of the switch pin
should be
held down under the fostening copscrew.
Ad just
the stop-light switch
so thot it
switches on the stop lights ot o pedol
trovel
of 10 to 15 mm meosured on the centre of the
pedol pod.
Adiust the pedol
trovel signolling switch so
thot the pushed-in
side push-button
pin
is
re,ecsed ot o pedol
trovel of 100 to 110 mm
mecsured on
the centre of the pedol
pod.
Press
the push
button into
the switch ofter hoving
completed the
odiustment.
12.2 ACCELERATOR PEDAL AND CABLE
The occelerotor pedol
forms o unit with its
self-lubricoting beoring ond the lever.
lt is
bolted to the f
loor tunnel. A coble possing
through the tunnel is ottoched to the pedol
lever ond the reloy
lever on the engine by
meons of clomps- The coble is protected
by
o Bowden tubing.
Pedol Removing ond Refitting
1. Loosen the clomp holding the coble on the
engine-mounted reloy lever. 2.
Remove the copscrews holding
down the
becrring with the pedol,
depress lightly the
pedol, ond lift it out of the f loor
tunnel together
with the beoring. 3. Disconnect the pedol
from the coble ofter
ioosening the clomp.
Removol ond Refitting of Bowden Tubing
ond Cqble
The Bowden tubing is
fostened to
the brocket
irr the floor tunnel by
meons of circlips. After
their removol, pull
the Bowden tubing inside
the cor. On ref
itting the tubing, lubricote it with
o low-viscosity oil (of
the SAE 20
closs). lt hos
been lubricoted with greose
in the foctory.
Fit
the clonrps so thot their longer ports (from
the
screw to their end) ore on the side of the
I evers.
Accelerotor Coble Adiustment
Adjust the coble so
thot it is not
excessively
tensioned or too slock. Loosen the clomps on
the engine side of the coble, move slightly
the
clomp toword the reloy lever,
ond tighten the
screws of the clomp.
12.3 GEAR SHIFT LEVER
AND LINKAGE
The geor shift mechonism consists of two
units: the geor
lever with its housing ond oc-
cessories, ond the geor
shifter rod
ond the
shifter lirrk with joint
(ot the georbox)
for
domping the vibrotion of the power
pock
tronsnritted to the geor
lever.
Removing Geor Lever
Housing ond Link
1. Lift owoy the mot from the floor tunnel in
the front ond reor comportment. lf seporote,
remove the individuol floor mots ofter hoving
prised out their clips with o screwdriver or
o similor tool. lf o one-piece floor
covering is
used, remove the door sill strips
on one side,
tip the seot, ond bend over the
floor covering.
2. Remove the geor
lever housing copscrews
ond prise
out the lid (next
to the clip) between
the seots. Proceed through the
operture to dls-
connect the bolted connection of the link with
the housing shifter rod.
3. Lift
owoy the housing with the lever
through the operture. Swivel the lever so thot
the shifter rod
does not protrude
over the
housing beoring thus obstructiong the removol.
4. Usuolly it is not necessory to remove the
geor shift link from
the cor. lf
obsolutely necess-
ory, the link con be
disconnected only ofter
162

nolly
emerges into spoce under the floor toword
the georbox.
lt is ottoched to the speedometer
by meons of o union nut ond to the georbox
by
o sleeve ond o screw.
It is lubricoted
with oil from the georbox
which creeps olong it due to copillory elev-
otion" Lubricote it with engine oil of o lower
viscosity dripped into its sheoth only if the
lubricotion by creeping is inodequote. When refitting
it in position, put
it into the
cor from the front, connect its
both ends, ond
then orronge it so thot it does not form ony
shorp bends ond is
not too tout. The speedo-
meter con be disconnected ofter removing
the
instrument ponel,
ond removed by pulling
it in
forword direction.
For the speedometer drive shoft possoge
under the ffoor refer to Chopter 12.7.
166

tificotion
number, or in
words. For exomple
Mobiloil 30 is on oil in the SAE 30 viscosity
closs, Mobiloil Speciol belongs to the SAE
10 W/30 closs. We quote
the viscosity closs
symbol of oils identified
in this woy in brockets
following the oil brond (trode
nome).
Oils designoted by o doubled viscosity closs
symbol ore the so-colled multigrode oils. Their
complionce with viscosity clossificotion is ex-
pressed by the symbol before the froction line
progressively to the clossificotion expressed by
the symbol behind the froction line. Thus,
for
instonce, the SAE 10W/30 oil hos the properties
of the sAE 10w, sAE 20w120,
ond sAE 30
closs.
Czechoslovok oils
Motor oil M6 AD (SAE
30), M4AD (SAE
20W/
20), Mogul Super SAE 20W50,
Mogul Speciol
SAE 2OW/30
Modit Oil SAE 30 (M6
AD), Modit Oil SAE
2OWl2O (M4AD), Modit Oil Speciol
SAE 10W/
30, Modit Super SAE 10W/40
Foreign oils
Agip: Agip F. 1 Motor Oil HD SAE 10W/20,
2OWl30, 4Ol5O; Agip F. 1
Super Motoroil
10w/40,20wl50
BP: Energol HD SAE 40, 30, 2OW (2OW|?O),
10W; Super Visco-Stotic 10Wi30, 10W/40,
20wt20
Costrof : Costrol 40,
30, 20Wl2O, '10
W; Costrolite
(SAE 10W/30), XL (SAE 20W/50);
GTX
(SAE 10w/50)
Mobil: Mobiloil 40, 30, 2OWl2O,
10W; Speciol
(SAE 10W/30); Speciol 20W/50; Super (SAE
10w/so)
Shef l; X-100 40, 30, 2OWl20,
10W; Super (SAE
10w/so)
Other oils of foreign moke con be used if equi-
volent to the listed bronds, for
exomple, Avio,
Esso, Heno (Optimol
LD), INA (Delto TLX),
Noftogos (Golox GTX, Omnio) etc.
GEAR OILS -
type E. P. (high-pressure)
I Viscosity j Ambient
Lubricoting noint
I closs
! temperoture
sAE 140*) -r50
to +15 oC
Georbox/f inol
drive SAE
90
*35 to -15
oC
* 5 to -30oC
SAE 80
teering box SAE 90 throughout
the yeor Czechoslovok
oils
PP 90 (SAE
90) geor
oil; PP 80 (SAE 80)
geor oil
Foreign oils
Agip: F. 1 Rotro 140; 85/90; 75Wl8O
BP: Geor Oil 140
EP; 90 EP; 80 EP
Costrol: Hypoy B 140; B 90; B 80
Mobil: Mobilube GX 140; GX 90; GX 80
Shell: Spirox E. P. 140; E. P. 90; E. P. 80 W
Other geor
oils of foreign moke con be used
if equivolent to the listed oils.
SPECIAL OILS
Distributor beorings (service inspection)
Czechoslovok moke -
ON 1 low'pour-point oil
Foreign moke -
for exomple, Shell Clovus 17
ond similor oils
GREASES -
use throughout the yeor
Woter pump
Czechoslovok moke -
SP 4 sooP greose,
NH 2
or A4 motor greose
Front wheel beorings, geor lever
brocket
Czechoslovok moke -
SP 4 or NH 2 soop greose
King pins
Czechoslovok moke -
A 00 motor greose
Inner door mechonisms, locking mechonisms
Czechoslovok moke -
SP 2-3 soop greose*)
Clutch releose beoring
Czechoslovok moke -
SP 4 or NH 2 soop
greose* )
Steering tinkoge boll
ioints, cronkshoft
beoring
Greoses listed in the porogroph
on greoses
of
foreign moke
Greoses of foreign moke:
Agip: F.1 Greose 30; BP: Energreose L2; Costrol:
Costroleose l. M.; INA: Automost Speciol;
Mobil: Mobilgreose MP;
Shell: Retimox A,
ond other greoses
equivolent to
the listed
ones.
BRAKE FLUID
To SAE J 1703C Specificotion
ln Czechoslovokio -
SYNTOL HD 190 broke fluid
Abrood -
SYNTOL HD 190, Pentosin
Super Fluid,
Mobil Hydroulic Broke Fluid, ATE Blou, BP
Broke Fluid, STOP SP 19
r) Greoses of foreign moke should be preferred.
220
*)
Not used
in Czechoslovokio