charging SKODA FABIA 2000 1.G / 6Y Workshop Manual

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
General pointsEdition 09.04
S00.5301.14.2002-1 page 3 02
Vehicle data sticker
The vehicle data sticker is located at the rear left on the
floor of the boot.
Storage of ŠKODA new vehicles
Notes on storage of new vehicles ⇒Technical Service
Handbook.
Vehicle handover from stock
–Before starting a stock vehicle, carry out a Pre-sales
Inspection.
–If the vehicle has been in stock for more than 6
months, replace the brake fluid.
–Inspect the electrolyte level of the battery and top up,
if necessary.
–Before the vehicle is sold, the recharging table must
be removed from the battery.
–If the battery is more than 52 weeks old or has been
recharged more than twice, it must be replaced with
a new battery.
Additional customer information regard-
ing inspection and maintenance
Information regarding the use of vehicles under
„severe conditions“:
–The service advisor should always point out to the
customer that the inspection intervals are based on
normal operating conditions.
–Under „severe conditions“ the inspection intervals
must be shortened.
„Severe conditions“ exist, for instance, if the vehicle is op-
erated continuously in one or several of the conditions
stated below:
♦Towing a trailer or when fitted with a roof rack.
♦Operated on dusty, poor, muddy roads or roads treat-
ed with road salt.
♦Driven for short distances and at ambient tempera-
tures below freezing point.
–If one or several of these „severe conditions“ exists,
please advise your customer whether it is necessary
to have work carried out between the normal service
intervals, such as:
♦Changing the engine oil before the normal specified
interval.
♦Cleaning or replacing the air filter element in the air fil-
ter housing.

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 3 02
Delivery Inspection (Export)
–Proper operation of seat belts, seat belt height adjuster, power windows and sun roof
–Inspect upholstery, interior trim, carpeting and footmats for cleanliness and damage
–Inspect all switches, all electrical components, gauges/indicators and controls02-6
–Radio: Inspect for proper operation, store stations, set clock, encode02-6
–Reset service interval display02-6
–Power windows: Inspecting positioning02-6
–Key switch for airbag deactivation, front passenger side: Check function „ON/OFF“ and
switch-over to the position „ON“02-7
–Fit net in luggage compartment (if available)
–Check the car tool kit, spare wheel and accessories, that they have all been supplied and
are properly secured
–Install the carpets supplied in the vehicle
–Perform a test drive
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5
–Inspect tyres and wheels for damage02-5
Concluding operations
–Interrogate fault memory of all systems, if necessary erase02-6
–Remove protective seat covers
–Remove recharging table (if affixed)
–Complete the service schedule, affix the vehicle data sticker in the Service Schedule to
the floor of the luggage compartment next to the spare wheel„Next Service Date“ sticker
and affix to the side of the dash panel on the driver's side, hand the card „Škoda Assist-
ance“ to the customer02-7
–Final inspection to ensure proper condition for handover to the customer
Inspections and operations to be completed Chapter
Vehicle (exterior)
–Plastic and rubber parts: Inspect for cleanliness and damage
–Inspect bodywork and paintwork for damage02-7
–Check operation of the tailgate lock and the fuel filler cap, door contact switch, operation
of the door handles, door locks and safety buttons, central locking from outside as well as
inside, child safety locks, ability to close all locks on the vehicle using all keys (including
the spare key)02-7
–Check operation of the anti-theft alarm system
–Tighten the wheel bolts to specified torque (steel and light alloy wheels 120 Nm), fit wheel
caps02-5
–Check the tyre inflation pressure (including spare wheel), if necessary correct the tyre in-
flation pressure, fit valve caps02-5
–Vehicles in stock for more than 6 months: Change brake fluid02-5

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 4 02
–Fit roof aerial
Engine compartment (from above)
–Check battery no-load voltage; recharge if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Brake fluid level (at „MAX“ marking)02-5
–Check the engine oil level (to be in-between the marking on the dipstick)02-3
–Check the coolant level (in-between marking), for special equipment antifreeze down to -
35 °C02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
–Check windscreen wiper and washer system, the spray nozzle adjustment and the resting
position of the windscreen wipers02-7
Vehicle interior
–Inspect upholstery, interior trim, carpeting and footmats for cleanliness and damage
–Inspect all switches, all electrical components, gauges/indicators and controls02-6
–Radio: Inspect for proper operation, store stations, encode, set clock02-6
–Fit net in luggage compartment (if available)
–Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), short introduction, technical data, support in the
case of a breakdown, other manuals (radio,...) ) - all in the vehicle log book pouch
–Reset service interval display02-6
–Power windows: Inspecting positioning02-6
–Key switch for airbag deactivation, front passenger side: Check function „ON/OFF“ and
switch-over to the position „ON“02-7
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5
–Inspect tyres and wheels for damage02-5
Concluding operations
–Perform a test drive02-9
–Interrogate fault memory of all systems, if necessary erase02-6
–Complete the service schedule, affix the vehicle data sticker in the Service Schedule to
the floor of the luggage compartment next to the spare wheel, complete the „Next Service
Date“ sticker and affix to the side of the dash panel on the driver's side02-7
–Remove recharging table (if affixed)
–Remove protective seat covers
–Install the carpets supplied in the vehicle
–Final inspection to ensure proper condition for handover to customer

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 2 02
1)Regular grade unleaded petrol (min. 91 ROZ) can be used although engine power output is slightly reduced.
Engine identifi-
cation charac-
tersAME ATZ AQW AUA BBY
Emission stand-
ardEU2 D4 EU4,
EU3 DDKEU3,
EU4,
EU2 DDK,
EU3 DDKEU4,
EU2 DDK,
EU3 DDK
Manufacturing
(from...through)08.99 ... 04.03 11.99 ... 07.00 08.00 ... 03.03 05.00 ... 03.02 03.02 ... 05.04
Displacement in
litres1,4 1,4
Output (kW at
rpm)50 / 5000 55 / 5000
Max. torque
(Nm at rpm)120 / 2500 126 / 3800
Bore (∅ mm) 75,5 76,5
Stroke (mm) 78 75,6
Compression 10 10,5
Hydraulic valve
clearance com-
pensationXX
Mixture forma-
tionSimos 3PB Simos 3PA Magneti Marelli 4LV
Fuel RON (mini-
mum)unleaded 95
1)
1) Regular grade unleaded petrol (min. 91 ROZ) can be used although engine power output is slightly reduced.
unleaded 951)
Fuel CN (mini-
mum)--
Firing order 1-3-4-2 1-3-4-2
Exhaust gas re-
circulation-X
Ignition system/
fuel injectionSimos 3PB Simos 3PA Magneti Marelli 4AV
Self-diagnosis X X
Catalytic con-
verterXX
Turbocharging - -
Charge air cool-
er--
Lambda probe X X
Camshaft ad-
justment--

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 3 02
Engine identification
charactersAMF AUB BBZ ASY
Emission standard EU3 EU4
EU2 DDK,
EU3 DDKEU4,
EU2 DDK,
EU3 DDKEU3
Manufacturing
(from...through)05.03 08.99 ... 05.02 05.02 08.99
Displacement in litres 1,4 1,4 1,9
Output (kW at rpm) 55 / 4000 74 / 6000 47 / 4000
Max. torque (Nm at rpm) 195 / 2200 126 / 4400 125 / 1600 - 2800
Bore (∅ mm) 79,5 76,5 79,5
Stroke (mm) 95,5 75,6 95,5
Compression 19,5 10,5 19,5
Hydraulic valve clearance
compensationXXX
Mixture formation Bosch PDE - injec-
torsMagneti Marelli 4LV Bosch VP
Fuel RON (minimum) -
unleaded 98
1)
1)Regular grade unleaded petrol (min. 95 ROZ) can be used although engine power output is slightly reduced.
-
Fuel CN (minimum) 49 - 49
Firing order 1-2-3 1-3-4-2 1-3-4-2
Exhaust gas recirculation X X X
Ignition system/fuel injec-
tionBosch PDE - injec-
torsMagneti Marelli 4AV Bosch VP
Self-diagnosis X X X
Catalytic converter X X X
Turbocharging X - -
Charge air cooler X - -
Lambda probe - X -
Camshaft adjustment - - -
Engine identification char-
actersATD ASZ AZL BMD BKY
Emission standard EU3 EU3 EU4,
EU2 DDK,
EU3 DDKEU4,
EU2 DDKEU4,
EU2 DDK
Manufacturing (from...through) 02.00 06.03 08.00 05.04 05.04
Displacement in litres 1,9 1,9 2,0 1,2 1,4
Output (kW at rpm) 74 / 4000 96 / 4000 85 / 5400 40 / 4750 55 / 5000
Max. torque (Nm at rpm) 240 / 1800 -
2800310 / 1900 170 / 2400 108 / 3000 126 / 3800
Bore (∅ mm) 79,5 79,5 82,5 76,5 76,5
Stroke (mm) 95,5 95,5 92,8 86,9 75,6

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 4 02
Engine fitted
The engine identification characters and serial number
are located in the front at the engine/gearbox joint.
In addition, a sticker with the engine identification charac-
ters and serial number is affixed to the timing belt guard.
Engine with identification characters ARV, AQV, AZE,
AZF, AME, ATZ and AQW.
Engine with identification characters AUA, AUB, BBY,
BBZ, BKY.Compression 19 19 10,5 10,3 10,5
Hydraulic valve clearance
compensationXX X X X
Mixture formation Bosch PDE -
injectorsBosch PDE -
injectorsBosch ME 7.5 Simos 3PG Magneti Marelli
4TV
Fuel RON (minimum) - -
unleaded 95
1)unleaded 951)unleaded 951)
Fuel CN (minimum) 49 49 - - -
Firing order 1-3-4-2 1-3-4-2 1-3-4-2 1-2-3 1-3-4-2
Exhaust gas recirculation X X - - X
Ignition system/fuel injection Bosch PDE -
injectorsBosch PDE -
injectorsBosch ME 7.5 Simos 3PG Magneti Marelli
4TV
Self-diagnosis X X X X X
Catalytic converter X X X X X
Turbocharging X X - - -
Charge air cooler X X - - -
Lambda probe - - X X X
Camshaft adjustment - - - - -
1)Regular grade unleaded petrol (min. 91 ROZ) can be used although engine power output is slightly reduced.
Engine identification char-
actersAT D A S Z A Z L B M D B K Y

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 1 02
02-6 Electrical System
Power windows: Inspecting positioning
If the battery is diconnected the power windows forget
their current position.
Test conditions:
•All car doors closed
The inspection procedure is carried out from the outside
Close window with the car key using the convenience
closing system.
–Turn car key into close position and hold until all the
windows are closed.
–After closing the windows hold the key in the close po-
sition for approximately another 3 seconds.
Electrical components: Check for proper
operation
–Inspect lighting, main headlights, headlight beam con-
trol, fog lights, turn signal lights, hazard warning light
system, tail lights, rear fog lights, reversing lights,
brake lights, parking light control for brightness and
proper operation.
–Inspect interior lights, illuminated storage compart-
ment, illuminated ashtray for proper operation.
–Airbag warning lamps: Check operation ⇒Chapter
02-7.
–Inspect warning buzzer, onboard computer, all switch-
es in centre console as well as on the dash panel and
horn for proper operation.
–Inspect power windows, exterior mirrors (heated and
electrically adjustable), central locking system, infra-
red remote control and convenience closing system
for proper operation
–Inspect heating of front seats for proper operation.
–Inspect radio for proper reception and absence of in-
terference, also inspect speakers ⇒02-6 page 2.
Battery: Testing no-load voltage
Special tools, test and measuring equipment and
auxiliary items required
♦Multimeter (e.g. -V.A.G 1526 A-)
Prior to the measurement the vehicle must have been in
the no-load state for at least two hours (no engine starts,
no charging or discharging of battery).
The following procedure applies to measuring the battery
voltage in the no-load state (after at least two hours):
–With the battery installed measure the voltage be-
tween the terminals (ignition switched off).