jump start terminals SKODA FABIA 2006 2.G / 5J Owner's Manual

Breakdown assistance229
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
– Have the tightening torque checked with a torque wrench as
soon as possible. Steel and light alloy wheels must be tightened to
a tightening torque of 120 Nm.
The safety wheel bolts on vehicles fitted with them (one safety wheel bolt per wheel) can only be loosened or tighte n up by using the adapter provided.
It is meaningful to note the code num ber hammered into the rear side of the adapter or the rear side of the safety wheel bolts. You can obtain a replacement adapter from a Škoda Service Partner, if necessary, by quoting this number.
We recommend that you always carry th e adapter for the wheel bolts with you in the vehicle. It should be stowed in the vehicle tool kit.
Caution
•Damage can occur to the adapter and sa fety wheel bolt if the safety wheel bolt is tightened up too much.
•On steel wheels, the theft-deterrent whee l bolt must always be installed in the hole, which is close to the valve. Otherwise the full wheel trim cannot be mounted and the full wheel trim can be damaged during the assembly.
Note
The set of safety wheel bolts can be obtained from a Škoda Service Partner.
Jump-starting
Initial steps
You can use the battery of another vehicle for jump-starting yours if the engine does not start because the battery on yo ur vehicle is flat. You will require jump- start cables for this purpose.
Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the battery supplying the power must not be si gnificantly less than the capacity of the discharged battery in your vehicle.
Jump-start cables
Only use jump-start cables which have an adequately large cross-section and insulated terminal clamps. Please pay attention to the manufacturer's instruc- tions.
Positive cable - colour coding in the majority of cases red.
Negative cable - colour coding in the majority of cases black.
WARNING
•A discharged battery may already freeze at temperatures just below 0°C. In case of frozen battery carry out no jump-starting - risk of explo- sion! Also after thawing of the battery there is a risk of caustic burns due to leaking acid. Replac e the frozen battery.
•Please pay attention to the warning instructions relating to working in the engine compartment ⇒page 198.
Note
•There must not be any contact between the two vehicles otherwise current may flow as soon as the negative terminals are connected.
NKO A05Fabia 20.book Page 229 Tuesday, September 26, 2006 8:38 AM

Breakdown assistance230
•The discharged battery must be properly connected to the system of the vehicle.
•Switch off any installed telephone and al so pay attention to the instructions for use of the telephone in such a situation.
•We recommend purchasing jump-start cables from Škoda Service Partners as a Škoda original accessory or from retailers who sell branded batteries.
Start engine
It is important to connect the jump-start cables in the correct order.
Connecting positive terminals
– Attach one end to the positive terminal ⇒fig. 162 of the
discharged battery .
– Attach the other end to the positive terminal of the battery
supplying the power .
Connecting negative terminal and engine block
– Attach one end to the negative terminal of the battery
supplying the power .
– Attach the other end to a solid metal part which is connected
firmly to the engine block, or to the engine block itself ⇒.
Starting engine
– Start the engine of the vehicle providing current and run the engine
at idling speed.
– Now start the engine of the vehicle with the discharged battery.
– Interrupt the attempt at starting an engine after 10 seconds if it
does not start right away and wait for about 30 seconds before
repeating the attempt.
– Disconnect the cables on the engine in exactly the reverse order
they were connected up.
WARNING
•The non-insulated parts of the terminal clamps must never make contact with each other. Furthermor e, the cable connected to the posi- tive terminal of the battery must not come into contact with electrically conducting parts of the vehicle - risk of a short circuit!
•Do not affix the jump starting cables to the negative terminal of the discharged battery. There is the risk of detonating gas seeping out the battery being ignited by the strong spark which results from the engine being started.
•Do not affix the cable end to pa rts of the fuel and brake system.
•Run the jump-start cables so that they cannot be caught by any rotating parts in the engine compartment.
Fig. 162 Jump-starting using the battery from another vehicle: A - flat vehicle battery, B - battery providing current
A1
AA
A2
AB
A3
AB
A4
A4
NKO A05Fabia 20.book Page 230 Tuesday, September 26, 2006 8:38 AM