headlights SKODA FABIA 2010 2.G / 5J Owner's Manual

Instruments and warning lights
16Shift into the next higher gear or select th
e selector lever position D of the automatic
gearbox before reaching the red zone of the rev counter scale. Avoid high engine speeds du
ring the driving time and before the engine has been
warmed up to operating temperature
page 145.
For the sake of the environment
Shif ting to a highe r g ear in g ood tim e hel p
s to reduce the fuel
consumption, minimises
operating noise levels, protects the environment and contributes to a longer life and reliability of the engine.SpeedometerWarning against excessive speeds* An acoustic warning signal will sound when
the vehicle speed exceeds 120 kilometres
per hour. The acoustic warning signal will switch off again when the vehicle speed goes below this speed limit.
Note
This function is only
valid for some countries.
Coolant temperature gauge*The coolant temperature gauge
page 15, fig. 15
operates only when the ignition
is switched on. In order to avoid any damage to the engine,
please pay attention to the following notes
regarding the temperature ranges. Cold range If the pointer is in the left-hand area of the scale it means that the engine has not yet reached its operating temperatur
e. Avoid running at high engine speeds, at full throttle
and at severe engine loads.
The operating range The engine has reached its operating temperature as soon as the pointer moves into the mid-range of the scale. The pointer may
also move further to the right at high
engine loads and high outside temperatures. This is not critical provided the warning symbol
 in the instrument cl
uster does not flash.
If the symbol
 in the instrument cluster flashes it means that either the coolant
temperature
is too high or the coolant
level
is too low. Observe the guidelines
 page 29, “Coolant temperature/coolant quantity
 ”.
WARNING
Pay attention to the warning notes
page 166, “Working in the engine
compartment” before opening the bonn
et and inspecting the coolant level.
Caution
Additional headlights and other attached components in front of the fresh air inlet impair the cooling effi
ciency of the coolant. There is
then a risk of the engine over-
heating at high outside temper
atures and high engine loads.
Fuel gauge*The fuel gauge
page 15, fig. 15
only operates when the ignition is switched on.
The fuel tank has a capacity of
about 45 litres. The warning symbol
 in the instrument
cluster lights up when the pointer reaches the reserve marking. There are now about 7 litres of fuel remaining in the tank.
This symbol is a reminder for you,
that you must
refuel
.
The following will be displayed in the information display*:
Please refuel!
An audible signal sounds as an additional warning signal.On some vehicles, the fuel gauge is shown
in the display of the instrument cluster.
A4
A7
s3j8.a.book Page 16 Tuesday, April 20, 2010 1:10 PM

Lights and Visibility
48Lights and VisibilityLightsSwitching lights on and off

Fig. 36 Dash panel: Light switch / fuse box: Switch for daylight driving lightsSwitching on side lights– Turn the light switch
fig. 36
- left into position
.
Switching on the low beam and main beam– Turn the light switch into position
.
– Press the main beam lever forward in order to switch on the main beam
 page 52, fig. 40
.
Switching off lights (except daylight driving lights)– Turn the light switch into position O. During the engine start, the low beam
lights are switched off automatically.
On vehicles fitted with
right-hand steering
* the position of the switches differs to
some extent from the position shown on
fig. 36
. The symbols which mark the switch
positions are identical, however.
WARNING
Never drive with side lights on - risk of accident! The side lights are not bright enough to light up the road sufficiently in front of you or to be seen by other oncoming traffic. In this case, always switch on the low beam when it is dark or if visibility is poor.
Note

O n R S v e h i c l e s w i t h s e p a ra t e l i g h t s * f o r d a
ylight driving lights (in the bumper below
the main headlights) these lights also serve as side lights.
An audible warning will sound if you wi
thdraw the ignition key and open the
driver's door when the vehicle lights are still on.
The acoustic warning signal is switched off over the door contact when the driver's
door is closed (ignition off). The vehicle
can be parked with
the side lights on.

If the car is parked for a lengthy period,
we recommend switching off all lights, or
leaving only the parking lights switched on.
The switching on of the described lights
should only be undertaken in accordance
with the legal requirements.
In the event of cool or humid
weather conditions
, the headlights can be misted up
from inside.
 The temperature difference between interior and external area of the headlight lenses is decisive.  When the driving lights are switched on,
the light outlet surfaces are free from
mist after a short period. The headlight lens
es can possibly mist up at the border
areas.  It also concerns reverse light and turn signal lights.  This mist has no influence on th
e life of the lighting system.
“DAY LIGHT” *Activating daylight driving lights*– Remove the cover of the fuse box on
the left side of the dash panel
page 195.
s3j8.a.book Page 48 Tuesday, April 20, 2010 1:10 PM

Lights and Visibility
49
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Turn the light switch into position O
page 48, fig. 36
- left.
– Switch on the switch for daylight driving lights
page 48, fig. 36
- right.
Activating daylight driving lights*
on vehicles with the “START-STOP”
system– Pull the turn signal light lever towards the
steering wheel, at the same time slide it
to the top and hold it in this position.
– Switch on the ignition - the right turn signal light flashes 4x.– Switch off the ignition - an audible signal
sounds, which confirms
the activation of
the daylight driving lights.
– Release the turn signal light lever.Deactivating daylight driving lights*– Switch off the switch for daylight driving lights
page 48, fig. 36
- right.
– Turn the light switch to the position side lights
 or low beam
 page 48,
fig. 36
- left.
Deactivating daylight driving ligh
ts* on vehicles with the “START-
STOP” system– Pull the turn signal light lever towards the
steering wheel, at the same time slide it
to the bottom and hold it in this position.
– Switch on the ignition - the left turn signal light flashes 4x.– Switch off the ignition - an audible signal
sounds, which confir
ms the deactivation
of the daylight driving lights.
– Release the turn signal light lever. On vehicles with separate ligh
ts* for daylight driving lights in the fog lights or in the
front bumper, the parking lights and the lice
nce plate light do not come on when acti-
vating the function daylight drivin
g lights (neither front nor rear).
If the vehicle is not equipped with separate lights* for daylight driving lights, the combination of the low beam, the parking ligh
ts (front and rear) including the licence
plate light is used as daylight driving lights.
In some countries, the national
legal provisions require that the rear parking lights also
come on together with the separate lights* for daylight driving lights when activating the function daylight driving lights.Halogen projector headlights with cornering light function*For a better cornering illumination, the halogen projector headlights with cornering light function are set in the optimal position in line with the vehicle speed and the steering angle. If the warning light
 comes on while driving or after the ignition is switched on, a
fault is confirmed.
WARNING
If there is a fault in the halogen projec
tor headlights with
cornering light func-
tion, the warning light
 lights up in the instrument cluster. The halogen
projector headlights with cornering light function are automatically lowered to the emergency position, which prevents a po
ssible dazzling of oncoming traffic.
Thus the illuminated length of the road is shortened. Drive carefully and have the car inspected immediately by a specialist garage.Tourist light*Halogen projector headlights with cornering light functionThis mode makes it possible to drive in countries with opposing traffic system, driving on the left/right, without dazzling the oncoming vehicles. When the mode “tourist light” is active, the side to side swivel of the headlights is deactivated.Activating tourist lightBefore activating the tourist light,
the following condit
ions must be met:
Ignition switched off, light switched off (light switch in the position O), control dial for the headlamp beam adjustment in the position
0, no gear engaged or selector lever in
the position
N (automatic gearbox), tourist light deactivated.
– Switch on the ignition.Up to 10 seconds after the ignition is switched on:
s3j8.a.book Page 49 Tuesday, April 20, 2010 1:10 PM

Lights and Visibility
51
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
If the vehicle is not fitted with fog lights*, the rear fog light is switched on by turning the light switch to the position
 and is pulled out directly to the position . This switch
does not have two position
s, but only one position.
The warning light
 lights up in the instrument cluster when the rear fog light is
switched on
page 26.
Only the rear fog light of the trailer lights up if the vehicle is fitted with a
towing device
from Škoda original accessories
and when you are towing a trailer which is fitted
with the rear fog light.
Caution
The rear fog light should only be switched on
if visibility is particularly poor (conform
with any varying legal provisions) to avoi
d dazzling vehicles be
hind your vehicle.
Headlamp range adjustment

Once the low beam is switched on
you can then adapt the range of the
headlights to the lo
ad of the vehicle.
– Turn the control dial
fig. 38
until you have adjusted the low beam so that
oncoming traffic is not dazzled.
Settings The positions correspond
approximately to the
following vehicle loads:
Front seats occupied, luggage compartment empty. All seats occupied, luggage compartment empty.
All seats occupied, luggage compartment laden. Driver seat occupied, luggage compartment laden.Caution
Set the headlight beam adjustment in su
ch a way as to avoid dazzling oncoming
traffic.Switch for hazard warning lights

– Press switch
 fig. 39
to switch the hazard warning light system on or off.
All the turn signal lights on the vehicle flas
h at the same time when the hazard warning
light system is switched on. The indicator
light for the turn signals and the indicator
light in the switch also flash at the same time. You can also switch on the hazard warning light system if the ignition is switched off. The hazard warning light system is switched on automatically if an airbag is deployed in the event of an accident. Please comply with any legal requirements when using the hazard warning light system.
Note
Switch on the hazard warning light system if, for example:
you encounter traffic congestion;

your vehicle breaks down or an emergency situation occurs.
A2
Fig. 38 Dash panel:
Lights and Visibility
A-A1
A2A3
Fig. 39 Dash panel: Switch for hazard warning lights
s3j8.a.book Page 51 Tuesday, April 20, 2010 1:10 PM

Lights and Visibility
56
Do not use the windscreen washer sy
stem at low temperatures, without
heating the windscreen beforehand.
Otherwise the window cleaner could
freeze on the windscreen and re
strict the view to the front.

In the event of a freezing up of the wi
ndscreen, first of al
l eliminate the ice
 page 157 and then operate the windscr
een wiper otherwise the windscreen
wiper blades could be damaged.
Caution
In frosty weather, please firs
t of all check whether the windscreen wiper blades are not
frozen to the windscreen before switching
them on. Switching on windscreen wipers
when the blades are frozen to the windscreen may result in damage both to the blades and the motor of the windscreen wipers!
Note
The content of the windscreen wiper reserv
oir is 3.5 litres. On vehicles which are
equipped with a headlight cleaning system*, the content of the reservoir is 5.4 litres.Headlight cleaning system*The headlights are being cleaned after the windscreen washer system has been oper- ated for the fifth time, the low beam or main
beam are switched on as well as the wind-
screen wiper lever is held in the position
page 55, fig. 46
for about 1 second.
You should remove stubborn dirt (such as in
sect residues) from the headlight lenses at
regular intervals, for example when refuelling
. Please refer to the following guidelines
 page 158, “The headlight lenses”. You should remove any snow from the fixtur
es of the washer nozzles and clear ice in
winter with a de-icing spray in order to
ensure proper operation of the cleaning
system.
Replacing wiper blades for the windscreen wipersTaking off the wiper blade– Fold windscreen wiper arm away from the windscreen. – Press the locking button, in order to un
lock the wiper blade and pull off in the
direction of arrow.
Attaching a wiper blade– Push the wiper blade until it locks up to the stop. – Check whether the wiper blade is correctly attached.– Fold the windscreen wiper ar
m back onto the windscreen.
Wiper blades in proper condition are essentia
l to obtain good visibility. Wiper blades
should not be allowed to become dirtied by
dust, insect remains and preserving wax.
Juddering or smearing of the wiper blades co
uld then be due to wax residues left on
the windscreen by vehicle washing in automa
tic vehicle wash systems. It is therefore
important to
degrease
the lips of the wiper blades after every pass through an
auto-
matic vehicle wash system
.
WARNING

If the windscreen wipers are handled ca
relessly, there is a risk of damage to
the windscreen.
WARNING (continued)
A5
Fig. 47 Wiper blade for the windscreen wiper
s3j8.a.book Page 56 Tuesday, April 20, 2010 1:10 PM

Driving and the Environment
150

Solvent-free protection of the vehicle for
transportation from the production plant
to the customer.
The use of solvent-free adhesives.

No CFCs used in the production process.

Without use of mercury.

Use of water-soluble paints.
Trade-in and recycling of old cars Škoda Auto meets the requirements of the brand and its products regarding environ- ment and ressource protection. All new Škoda
vehicles can be utilized up to 95% and
always
11) be returned. In a lot of countries sufficient trade-in networks have been
created, where you can trade-in your vehicle.
After you trade-in your vehicle, you will
receive a confirmation stating the recycling
in accordance with environmental regula-
tions. Vehicles with special built-on types Technical documents regarding changes carried
out on the vehicle must be kept by the
vehicle user, in order to hand over later to the old car user. This ensures the recycling in accordance with en
vironmental regulations.
Motoring abroadGeneral Other circumstances may exist abroad.It is also possible, in certai
n countries, that the
Škoda Service Partner network is limited
or has not been established yet. This is
the reason why obtaining certain spare parts
may be somewhat complicated and specialist
garage personnel may only be able to
make limited repairs. Škoda
Auto in the Czech Republic and relevant importers are
happy to provide information
about technical aspects of the vehicle, required mainte-
nance work and possibilities for getting repairs done.
Unleaded petrolA vehicle fitted with a petrol engine must
always be refuelled
with unleaded petrol
 page 146. The automobile associations can provide you with information regarding the locations of filling stations which offer unleaded petrol.HeadlightsThe low beam of your headligh
ts is set asymmetrically. It illuminates the side of the
road on which you are driving to a greater ex
tent. If you drive abroad on the other side
of the road, you will da
zzle oncoming traffic.
Halogen projector headlights The adaptation of the headlights (valid for vehicles which are designed for driving on the left and on the right) must be performe
d by switching over a bezel by a specialist
garage. Halogen headlight When using Halogen headlights, it is necessary to stick a sticker over a certain part of the headlights in order to prevent the dazzling of oncoming traffic. You can purchase headlight stickers from
the range of the Škoda original parts.
Note
You can obtain further information regardin
g masking over or converting the head-
lights from your specialist garage.Avoiding damage to your vehicleWhen driving on poor roads and lanes or when driving over kerbstones, steep ramps etc., you must pay particular attention to
ensuring that any low-slung parts of the
vehicle, such as spoiler and exhaust,
do not touch the ground and get damaged.
This particularly applies to models with a lowered suspension (sport suspension) and also when your vehicle is fully laden.
11)Subject to fulfilment of the national legal requirements.s3j8.a.book Page 150 Tuesday, April 20, 2010 1:10 PM

Towing a trailer
152
Towing a trailerTo w i n g a t r a i l e rTechnical requirements The towing device must satisfy certain technical requirements.Your vehicle is designed primarily for tr
ansporting persons and luggage. It can,
however, also be used for towing a traile
r - provided certain technical equipment is
fitted. If your vehicle has been eq
uipped with a towing device
from Škoda Original Accesso-
ries, then the towing device satisfies all technical and legal requirements. Your vehicle is fitted with a 13-pin power so
cket for the electrical connection between
the vehicle and trailer. If the tr
ailer which you wish to tow has a
7-pin connector
, you
can use a suitable adapter
12) from Škoda original accessories.
This work must be carried out in accordance
with the manufacturer's specifications if
a towing device is retrofitted. Specialist garages are familiar with details re
lating to retrofitting a towing device and
for any necessary modifications to the cooling system.
WARNING
We recommend that you have the towing device from Škoda original accesso-ries installed by a specialist garage. He
is familiar with all the relevant details
relating to retrofitting such equipment. There is a risk of an accident if the towing device is not properly fitted!General Maintenance There are a number of points to pay attention to when towing a trailer.Trailer load The permissible trailer load must
on no account be exceeded.
You can negotiate appropriately steeper inclin
es and descents if you do not make full
use of the permissible trailer load. The trailer loads specified only apply for
altitudes
up to 1 000 metres above mean sea
level. On petrol engines without forced indu
ction, the engine power output drops with
increasing height due to a lowering of air pr
essure and thus the ability to climb, this
means that the trailer load must be reduced by 10% for every further increase of 1 000 metres in height above sea le
vel. The towed weight is the weight of the (laden) vehicle
and the (laden) trailer together. One should ta
ke this into account before driving up to
higher altitudes. Petrol engines with forced induction use an air pressure correction method, so that their power output does
not depend on the he
ight above sea level.
The trailer and drawbar load information on the type plate of the towing device are merely test data for the towing device
The data relating to your vehicle, which
is often less than this test data, can be found in your vehicle registration docu- ments. Distribution of the load Distribute the load in the trailer in such a
way that any heavy items are located as close
as possible to the axle. Secure th
e items to preven
t them slipping.
Tyre pressure Correct the tyre inflation pressure on yo
ur vehicle for that of “fully laden”,
page 178.
The inflation pressure of the tyres fitted to
the trailer adjust in accordance with the
manufacturer's recommendation. Exterior mirrors You have to have additional ex
terior mirrors fitted if you are not able to see the traffic
behind the trailer with the standard rear-view mirrors. Both exterior mirrors should be attached to folding arms. Adjust the mirrors so that they provide you with an adequate field of view to the rear. Headlights Before starting off with a hitched trailer, al
so check the setting of the headlights. Alter
the setting as necessary with the aid of the headlight beam adjuster
page 51.
12)In some countries the adapter is supplied with the towing device.s3j8.a.book Page 152 Tuesday, April 20, 2010 1:10 PM

Taking care of your vehicle and cleaning the vehicle
158
Do not affix any stickers over the inside of
the rear window to avoid damage to the
heating elements of the rear window heater
.
We recommend using a preserva
tive from Škoda genuine accessories offered by your
Škoda dealer.
Caution

Never remove snow or ice from the glass pa
rts with warm or hot water - risk of
formation of cracks in the glass!
When removing snow or ice from the windows and mirror lenses make sure not to
damage the paintwork of the vehicle.The headlight lensesPlease do not use any aggressi
ve cleaning or chemical so
lvent products for cleaning
the front headlights - risk of
damage to the
plastic lenses.
Please use
soap and clean
warm water.
Caution
Never
wipe the headlights dry and do not use any sharp objects for cleaning the plastic
lenses, this may result in damage to the
protective paintwork and consequently in
formation of cracks on the headlight lenses, e.g through effect of chemical products.Door and window sealsThe rubber seals on the doors, boot lid,
bonnet and windows remain supple and last
longer if you treat them from time to time with a rubber care product (e.g. with a spray with silicone-free oil). You also avoid premature wear of the seals and prevent leakages in this way. It is also easier to open the doors. Rubber seals which are well cared for also do not stick together in cold winter weather.Locking cylinderWe recommend that you use the spray from Škoda original accessories with regreasing and anticorrosive effect for de-icing locking cylinders.
Note
When washing your vehicle, ensure that as
little water as possible gets into the locking
cylinders.WheelsSteel wheels You should also thoroughly wash the wheels
and wheel trims when giving your vehicle
its regular wash. This prevents any brake dust, dirt and road salt from sticking to the wheel hubs. You can remove stubborn brake
abrasion adhering to the wheels with an
industrial cleaner. Touch up
any damage to the paintwork on the wheels before rust is
able to form. Light alloy wheels Regular care of light alloy wh
eels is necessary in order to retain their decorative
appearance over long periods. It is particul
arly important to remove any road salt and
brake abrasion from light alloy wheels every two weeks, otherwise the surface will suffer. Wash thoroughly and then treat the wheels with a protective product for light alloy wheels which does not
contain any acidic componen
ts. You should provide the
wheel hubs with a hard wax layer every thre
e months. You must not use any products
which cause abrasion when treating the wheel hubs. Any damage to the paint layer on the wheel hubs must be touched up immediately. We recommend using a preservative from Šk
oda genuine accessories offered by your
Škoda dealer.
WARNING
One should remember when cleaning th
e wheels that moisture, ice and road
salt may adversely affect braking ef
ficiency - risk of an accident!
Note
Severe layers of dirt on the wheels can also
result in wheel imbalance. This may show
itself in the form of a wheel vibration which
is transmitted to the steering wheel which,
in certain circumstances, can
cause premature wear of the
steering. This means it is
necessary to remove the dirt.
s3j8.a.book Page 158 Tuesday, April 20, 2010 1:10 PM

Inspecting and replenishing
176
Caution
On vehicles with the “START/STOP” system,
the pole terminal of the charger must not
be connected directly to the negative termin
al of the vehicle battery, but only to the
engine earth
page 192, fig. 158
.
Disconnecting and reconnecting the batteryOn disconnecting and reconnecting the batt
ery the following functions are initially
deactivated or are no longer able to operate fault-free. We recommend having the vehicle checked by a specialist garage to ensure full func- tionality of all electrical systems.Replacing the batteryYou should only replace a battery with a ne
w battery of the same
capacity, voltage (12
V), amperage and of the same size. Specialist garages have a range of suitable batteries available. We recommend that you only have an old ba
ttery disposed of by a specialist garage
since it does require special disposal.
For the sake of the environment
Batteries contain poisonous substances such
as sulphuric acid and lead. They must be
disposed of in accordance with local environmental protection regulations and on no account as domestic waste.
Windshield washer systemThe windshield washer reservoir contains the
cleaning fluid for the
windscreen or rear
window and for the headlamp cleaning system*.
The reservoir is located in the front of
the engine compartment on the right side of the vehicle
fig. 146
. On some vehicles,
the reservoir is located on the left si
de of the vehicle next to the battery.
The
filling level
of the container is about 3.5 litres and about 5.4 litres on vehicles
which have a headlight washing system. Clear water is not sufficient to intensivel
y clean the windscreen and headlights. We
therefore recommend using clean washing water together with the screen cleaner from Škoda genuine accessories (in winter additionally with antifreeze) which is capable of removing stubborn
dirt. Follow the instructions for use on the packaging
when using screen cleaning products. You should always add antifreeze to the cleani
ng water in winter even
if your vehicle is
fitted with heated wind
screen washer nozzles*.
It is also possible in exceptional cases to use methylated spirits when no screen cleaner with antifreeze is available. The concentration of methylated spirits must not be more than 15 %. Please note, however, that the anti
freeze protection at this concentration is
only adequate down to -5°C.
WARNING
Read and observe the warning notes
page 166, “Working in the engine
compartment” before working in the engine compartment.
Operation
Operating measure
Electrical power window
(operational faults)
page 45
Enter radio code number
see Radio Operat
ing Instructions
Set hours
page 18
Data in the multi-functional indicator* are deleted.
 page 19
Fig. 146 Engine compartment: Wind- shield washer fluid reservoir
s3j8.a.book Page 176 Tuesday, April 20, 2010 1:10 PM

Inspecting and replenishing
177
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Caution

On no account should you add radiator an
tifreeze or other additives to the wind-
screen washer fluid.
If the vehicle is fitted with a headligh
t cleaning system, you should only add
cleaning products which do no
t attack the polycarbonate co
ating of the headlights to
the windscreen washer fluid. Please contac
t your specialist garage, who will tell you
which cleaning agent you can use.
Note
Do not take the filter out of the windscreen
wash container when filling it up again with
liquid otherwise dirt can get into the liquid
transportation system and can lead to faults
in operation of the windscreen wash system.
s3j8.a.book Page 177 Tuesday, April 20, 2010 1:10 PM