service reset SKODA FABIA 2010 2.G / 5J Owner's Manual
[x] Cancel search | Manufacturer: SKODA, Model Year: 2010, Model line: FABIA, Model: SKODA FABIA 2010 2.G / 5JPages: 244, PDF Size: 29.53 MB
Page 16 of 244
Instruments and warning lights
15
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Instruments and warning lightsOverview of the instrument cluster
Engine revolutions counter
page 15
Display with counter for distance driven
page 17
with Service Interval Display
page 17
with digital clock
page 18
with Multi-functional indicator*
page 19
with Information display*
page 22
Speedometer
page 16
Coolant temperature gauge*
page 16
Button for display mode: Set hours / minutes Activating / deactivating the second speed in mph or km/h* Service interval - Display of the remaining number of days, kilometres or miles to the next Inspection Service / Reset*
1)
Button for: Reset trip counter for distance driven Resetting Service
Interval Display
Set hours / minutes Activate / deactivate display mode Fuel gauge*
page 16
Engine revolutions counterThe red zone of the rev counter scale
fig. 15
indicates the range in which the
engine control unit begins to limit the engi
ne speed. The engine
control unit restricts
the engine speed to a steady limit value.
Fig. 15 Instrument cluster
A1A2A3A4A5
1)Valid for countries where the values ar
e indicated in British measuring units.
A6A7
A1
s3j8.a.book Page 15 Tuesday, April 20, 2010 1:10 PM
Page 18 of 244
Instruments and warning lights
17
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Caution
Never run the fuel tank completely empty!
The irregular supply of the fuel system can
lead to irregular runni
ng of the engine. Unburnt fuel may get into the exhaust system
and damage the catalytic converter.Counter for distance drivenThe counter for the distance driven is loca
ted in the bottom area of the display. The
distance which you have driven
with your vehicle is shown
in kilometres (km). In some
countries the measuring
unit “mile”
is used.
Reset button If you hold the reset button
page 15, fig. 15
pressed for about 1 second, the trip
counter is set back to zero. Trip counter for distance driven The trip counter indicates the distance which
you have driven since it was last reset -
in steps of 100 metres or 1/10 of a mile. Counter for distance driven The counter for distance driven indicates th
e total distance in kilometers or miles
which the vehicle has been driven. Fa u l t d i s p l a y If there is a fault in the instru
ment cluster, the constant text
Error
appears in the display.
Have the fault rectified as soon as
possible by a specialist workshop.
WARNING
Never seek to adjust the trip counter for
distance driven while driving for safety
reasons!
Note
If vehicles which are fitted with the inform
ation display* the display of the second
speed is activated in mph or km/h, this driving speed is indicated instead of the counter for the total distance driven.
Service Interval DisplayDepending on the equipment installed in the vehicle, the text can differ on the display. Service Interval Display Before the next service interval a key symbol
and the remaining kilometers are
indicated after switching on the ignition
fig. 16
. At the same time, a display appears
regarding the remaining days until the next service interval. The following will be displayed in the information display*:
Service in ... km or ... days
The kilometre indicator or the days indicator reduces in steps of 100 km. or days until the service due date is reached. A flashing key symbol
and the text
Service
appears in the display for 20 seconds
as soon as the due date for the service is reached. The following will be displayed in the information display*:
Service now!
Display regarding the distance and days
until the following service interval
You can use the button to display the rema
ining distance driven and the days until
the next service interval
page 15.
A key symbol
and a display regarding the remaining kilometers appear for 10
second in the display. At the same time, a display appears regarding the remaining days until the next service interval.
A6
Fig. 16 Service Interval Display: Note
A5
s3j8.a.book Page 17 Tuesday, April 20, 2010 1:10 PM
Page 19 of 244
Instruments and warning lights
18On vehicles which are equipped with inform
ation display*, you ca
n call up this infor-
mation in the menu
SETUP
page 23.
The following will be displayed in the information display* for 10 seconds:
Service in ... km or ... days
Resetting Service Interval Display It is only possible to reset the Service Interval Display, if a service message or at least a pre-warning is shown on the display of the instrument cluster. We recommend having this resetting performed by a specialist garage.The specialist garage:
resets the memory of the display after the appropriate inspection;
makes an entry in the Service schedule;
affix the sticker with the entry of the following service interval to the side of the
dash panel on the driver's side. Reset the service interval displays by using the reset button
page 15 on the trip
counter. On vehicles which are equipped with inform
ation display*, you ca
n call up this infor-
mation in the menu
SETUP
page 23.
Caution
We recommend that you do not reset the Se
rvice Interval Display
yourself otherwise
this can result in the service interval display being incorrectly set, which may also result in problems with operation of your vehicle.
Note
Never reset the display between service intervals otherwise this may result in
incorrect readouts.
information is retained in the Service Interval Display also after the battery of the
vehicle is disconnected.
If the instrument cluster is exchanged af
ter a repair, the correct values must be
entered in the counter for the Service Interval Display. This work is carried out by a specialist garage.
The data displayed is the same after resetting the display with flexible service inter-
vals (QG1) using the reset button as that for a vehicle with fixed service intervals (QG2). We therefore recommend having the Service In
terval Display reset
only by an author-
ised Škoda Service Partner who is familiar with the procedure for resetting the display with a vehicle system tester.
Please refer to the brochure Service schedule for extensive information about the
service intervals.Digital clockThe time is set with the buttons and
page 15, fig. 15
.
Select the display which you wish to ch
ange with the button and carry out the
change with the button . On vehicles which are fitted out with the information display*, it is possible to set the time in the menu
Time
page 24.
WARNING
The clock should not be adjusted while driving for safety reasons but only when the vehicle is stationary!Shift recommendation for changing gears*An information for the engaged gear
fig. 17
is shown in the display of the instru-
ment cluster.
A6
A5
A6
A5
A6
Fig. 17 Shift recommendation for changing gears
AA
s3j8.a.book Page 18 Tuesday, April 20, 2010 1:10 PM
Page 26 of 244
Instruments and warning lights
25
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Language Here you can set in which language the
warning and information texts should be
displayed. Displays of the MFA Here you can switch off or on certain di
splays of the multi-
functional indicator.
Time Here you can set the time, the time format (12 or 24 hour indicator) and the time change summer/winter time. Winter tyres Here you can set at which speed a warning si
gnal should sound. This function is used
for e.g winter tyres with the permissibl
e maximum speed less than the maximum
speed of the vehicle. When exceeding the speed, the following is
displayed on the information display*:
Winter tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Measures Here you can set the units for temperat
ure, consumption and distance driven.
Second speed Here you can switch on the display of
the second speed in mph or in km/h
2).
Service Here you can have the kilometers still to
be driven and the days until the following
service interval shown and the Service Interval Display reset. Factory Setting After selecting the menu point
Factory Setting
the factory setting of the information
display is established again.2)Valid for countries where the values are indicated in British measuring units.
s3j8.a.book Page 25 Tuesday, April 20, 2010 1:10 PM