headlight bulb SKODA OCTAVIA 2008 2.G / (1Z) Owner's Manual

Instruments and Indicator/Warning Lights
34
Further information about the turn signal system ⇒page 65.
Fog lights 
The warning light  comes on when the fog lights are operating ⇒page 62.
Main beam 
The indicator light  comes on when the main beam is selected or also when the
headlight flasher is operated.
Further information about the main beam ⇒page 65.
Low beam 
The warning light  comes on when low beam is selected ⇒page 59.
Rear fog light 
The warning light  comes on when the rear fog lights are operating ⇒page 63.
Cruise control system* 
The warning light  lights up, when operating the speed regulating system.
Failure of the light bulbs 
The warning light  comes on if a light bulb is damaged:
•up to 2 seconds after the ignition is switched on;
•when switching on the defective light bulb. The following text e.g will be displayed in the information display*:
Check front right dipped beam!
The rear side lights and the licence plate lighting require several light bulbs. The
indicator light
 only lights up if all light bulbs of the licence plate lighting or the
parking light (in one rear light unit) are defe ctive. Check regularly the function of the
light bulbs.
Diesel particle filter*  (diesel engine)
If the warning light  comes on, this means that soot has accumulated in the
diesel particle filter because of the frequent short distances.
In order to clean the diesel particle filter, the vehicle should be driven at an even
speed of at least 60 km/h at engine speeds of 1 800 - 2 500 rpm for at least 15
minutes or until the warning light goes ou t with the 4th or 5th gear engaged (auto-
matic gearbox: position S) when the traffi c situation permits it. This increases the
exhaust temperature and the soot deposited in the diesel particle filter is burnt.
Always pay attention to the valid speed limits ⇒.
The warning light
 goes out after the successful cleaning of the diesel particle
filter.
If the filter is not properly cleaned, the warning light
 does not go out and the
warning light  begins to flash. In the information display* appears Diesel-
particle Owner's manual . Afterwards the engine contro l unit shifts the engine into
the emergency mode, which only has a re duced power output. After switching the
ignition off and on again the warning light
 comes on.
Have the vehicle inspected without delay by your specialist garage.
WARNING
•If you do not pay attention to the warning light coming on and the corre-
sponding descriptions and warning notes, this may result in injuries or
major vehicle damage.
20A5Facelift.book Page 34 Saturday, September 6, 2008 2:13 PM

Lights and Visibility
64
Headlamp range adjustment 
Once the low beam is switched on you can then adapt the range of
the headlights to the load of the vehicle.
– Turn the control dial ⇒fig. 60 until you have adjusted the low beam
so that oncoming traffic is not dazzled.
Settings
The positions correspond approximat ely to the following vehicle loads:
Front seats occupied, lu ggage compartment empty.
All seats occupied, luggage compartment empty.
All seats occupied, luggage compartment laden.
Driver seat occupied, luggage compartment laden.
Caution
Set the headlight beam adjustment in su ch a way as to avoid dazzling oncoming
traffic.
Note
Headlights fitted with Xenon bulbs* adapt automatically to the load and driving
state of the vehicle (e.g. accelerating, braking) when the ignition is switched on and
when driving. Vehicles which are equi pped with Xenon bulbs* do not have a
manual headlight range adjustment control.
Switch for hazard warning lights 
–Press switch  ⇒ fig. 61 to switch the hazard warning light system on
or off.
All the turn signal lights on the vehicle flash at the same time when the hazard
warning light system is switched on. The indicator light for the turn signals and the
indicator light in the switch also flash at the same time. You can also switch on the
hazard warning light system if the ignition is switched off.
The hazard warning light system is switch ed on automatically if an airbag is
deployed in the event of an accident.
Please comply with any legal requirements when using the hazard warning light
system.
Fig. 60 Dash panel: Lights
and Visibility
A-
A1
A2
A3
Fig. 61 Dash panel: Switch
for hazard warning lights
20A5Facelift.book Page 64 Saturday, September 6, 2008 2:13 PM

Lights and Visibility65
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Note
Switch on the hazard warning light system if, for example:
•you encounter traffic congestion,
•your vehicle breaks down or an emergency situation occurs.
The turn signal   and main beam lever 
The parking lights and headlight flas her are also switched on and off
using the turn signal and main beam lever.
The turn signal and main beam lever perform the following functions:
Right
 and left  turn signal light
– Push the lever upwards or downwards ⇒fig. 62 .
– If you only wish to flash three times* (the so-called convenience turn signal), push the lever briefly up to the upper or lower pressure point
and release it. This function can be activated/deactivated in the infor-
mation display* ⇒page 26.
– Turn signal for changing lanes - in or der to only flash briefly, move the
lever up or down to the pressure po int and hold it in this position. Main beam

– Switch on the low beam.
– Push the lever forwards.
– Pull the lever back into the initial position in order to switch the main
beam off again.
Headlight flasher

– Pull on the lever of the steering wheel (sprung position) - the main beam and warning light in the instrument cluster come on.
Parking light

– Switch off the ignition.
– Push the lever up or down - the right-hand or left-hand parking light is switched on.
Information concerning the function of the lights.
•The turn signal system only operates when the ignition is switched on. The
corresponding indicator light  or  in the instrument cluster also flashes.
•The turn signal is automatically cancelled after negotiating a curve.
•The indicator light flashes at twice its normal rate if a bulb of the turn signal light
fails.
•The side light and rear light on the appropriate side of the vehicle are switched
on when the parking light is selected. The parking light only operates if the ignition
is switched off.
Caution
Use main beam or the headlight flasher only if this does not risk dazzling other road
users.
Fig. 62 Turn signal and main
beam lever
20A5Facelift.book Page 65 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs
258
Fuse cover in engine compartment
The fuse box in the engine comp artment exists in two different
versions. You can determine which vers ion your vehicle is fitted with
after removing the fuse cover at the location of the fuses.
For particular model versions, the battery must be removed before
removing the fuse cover ⇒page 232.
Removing fuse cover
– Move the circlips ⇒fig. 236 as far as the stop, the symbol

appears behind the circlip and remove the cover.
Installing fuse cover
– Position the fuse cover on the fuse box and push the circlips as far as the stop - the symbol
 is visible behind the circlip.
Caution
•When unlocking and locking the fuse cover, it must be pressed on the sides to
the box, otherwise damage can occur to the locking mechanism.
•Carefully position the fuse cover in the engine compartment. If the cover was
not correctly positioned, water can get into the fuses and this results in a damage
to the vehicle!
Fuse assignment in engine compartment - version 1
Certain electrical components are only standard on certain vehicle model versions
or only suppliable as optional equipment for certain models.Fig. 236 Fuse cover in engine
compartment
AA
AA
No.Power consumerAmperes
F1Central control unit, right main headlight, right rear light
unit30
F2Valves for ABS20
F3Not assigned
F4Measuring circuit5
F5Horn15
F6Not assigned
F7Valve for fuel dosing15
F8Not assigned
F9Activated charcoal filter, exhaust gas recirculation valve10
F10Leakage diagnosis pump10
F11Lambda probe upstream of catalytic converter, engine
control unit10
F12Lambda probe downstream of catalytic converter10
Fig. 237 Schematic repre-
sentation of fuse box in
engine compartment -
version 1
20A5Facelift.book Page 258 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs259
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
F13Control unit for automatic gearbox15
F14Not assigned
F15Coolant pump10
F16Not assigned
F17Instrument cluster, windshield wiper lever and turn sig-
nal light lever5
F18Audio amplifier (sound system)30
F19Radio15
F20Phone5
F21Not assigned
F22Not assigned
F23Engine control unit10
F24Control unit for CAN databus5
F25Not assigned
F26Not assigned
F27Not assigned
F28Engine control unit15
F29Actuation for coolant pump after-running5
F30Control unit for auxiliary heating20
F31Front window wiper30
F32Not assigned
F33Not assigned
F34Not assigned
F35Not assigned
F36Not assigned
No.Power consumerAmperes
F37Not assigned
F38Radiator fan, valves10
F39Clutch pedal switch, brake pedal switch5
F40Ignition coils20
F41Not assigned
F42Actuation of fuel pump5
F43Not assigned
F44Not assigned
F45Not assigned
F46Not assigned
F47Central control unit, left main headlight, left rear light
unit30
F48Pump for ABS40
F49Power supply for terminal 15 (ignition on)40
F50Not assigned
F51Not assigned
F52Power supply relay - terminal X a)40
F53Accessory equipment50
F54Not assigned
a)In order not to drain the battery unnecessarily when starting the engine, the electrical com-
ponents of this terminal are automatically switched off.
No.Power consumerAmperes
20A5Facelift.book Page 259 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs
260
Fuse assignment in engine compartment - version 2
Certain electrical components are only st andard on certain vehicle model versions
or only suppliable as optional equipment for certain models.
No.Power consumerAmperes
F1Not assigned
F2Control unit for automatic gearbox DQ 20030
F3Measuring circuit5
F4Valves for ABS30/20
F5Control unit for automatic gearbox15
F6Instrument cluster, windshield wiper lever and turn sig-
nal light lever5
F7Power suppy terminal 15, Starter40
F8Radio15
F9Phone5
F10Engine control unit, Main relay5/10
F11Control unit for auxiliary heating20
F12Control unit for CAN databus5
Fig. 238 Schematic repre-
sentation of fuse box in
engine compartment -
version 2
F13Engine control unit15/30
F14Ignition20
F15Lambda probe, NOx-sensor, Fuel pump relay
Glow plug system relay15 5
F16Central control unit, right main headlight, right rear light
unit30
F17Horn15
F18Amplifier for digital sound processor30
F19Front window wiper30
F20Water pump10
F21Lambda probe10/15
F22Clutch pedal switch, brake pedal switch5
F23Secondary air pump
Air mass meter
Fuel high pressure pump5
10
15
F24Activated charcoal filter, exhaust gas recirculation valve10
F25Pump for ABS30/40
F26Central control unit, left main headlight, left rear light
unit30
F27Secondary air pump
Preglowing40
50
F28Not assigned
F29Power supply terminal 3050
F30Te r m i n a l Xa)40
a)In order not to drain the battery unnecessarily when starting the engine, the electrical com-
ponents of this terminal are automatically switched off.
No.Power consumerAmperes
20A5Facelift.book Page 260 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs
262
Electrically adjustable seats are protected by automatic circuit breakers, which
switch on again automatically after a few seconds after the overload has been
eliminated.
Bulbs
Changing bulbs
The relevant lamp must always be switch ed off before a light bulb is replaced.
Defect light bulbs should only be replaced with light bulbs of the same type. The
designation is located on the light socket or the glass bulb.
Changing certain bulbs is not something wh ich you can do yourself, but requires to
be done by a specialist. Other parts of the vehicle must be removed in order to change the light bulbs. This applies, in particular, to bulbs which can only be
reached from the engine compartment.
We therefore recommend that you have any bulbs changed by a Škoda Service
Partner or, in exceptional cases, by ca
lling on other professional assistance.
Please note that the engine compartment is a hazardous area ⇒page 225,
“Working in the engine compartment”.
We recommend that you carry the set of light bulbs with you which was delivered
in your vehicle. Replacement light bulbs
23) are available at specialist garages.
The set of light bulbs can be stowed in the locable box in the spare wheel.
Fitted with a xenon headlight
Change of light bulbs on Xenon lights (low beam lights, parking lights and main
beam lights) should be undertaken by a specialist garage.
Overview of bulbs
36Headlight cleaning system20
37Front seat heating30
38Heated rear seats30
39Not assigned
40Air blower for heating and air conditioning40
41Rear window wiper15
42Not assigned
43To w i n g d e v i c e15
44To w i n g d e v i c e20
45To w i n g d e v i c e15
46Heated windscreen washer nozzles5
47Relay for auxiliary heating5
48Not assigned
49Light switch5
No.Power consumerAmperes
23)Replacement light bulbs are, on the other hand, part of the basic equipping of the vehicle in
some countries.
Front headlightHalogen headlightXenon headlight
Low beam H7D1S
Main beam lightH1
Parking lightsW5W/W5W BL
Daylight driving lights*PY21W SLL/LEDa)
a)Octavia RS
Tu r n s i g n a l sPY21W
Fog lightsH8/HB4a)
20A5Facelift.book Page 262 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs263
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
•Bulbs H7 and H1 are pressurised and may burst when changing the bulb
- risk of injury!
•It is recommended to wear gloves and eye protection when changing a
light bulb.
•Gas discharge bulbs* (xenon bulbs) op erate with a high voltage, profes-
sional knowledge is required - danger to life!
Caution
Do not take hold of the glass bulb with naked fingers (even the smallest amount of
dirt reduces the working life of the light bu lb). Use a clean cloth, serviette or some-
thing similar.
Note
This Owner's Manual only describes the replacement of bulbs where it is assumed
that no major complications wi ll arise. Other light bulbs should be changed by your
specialist garage.
Front headlight
Light unit (Octavia)Bulb
Reversing lightP21W
Tu r n s i g n a l sPY21W
Twin filament light bulb for the brake lights and tail
lightsP21/4W
Twin filament light bulb for the rear fog lights and tail
lightsP21/4W
Parking lightsW3W
Rear light unit (estate car)Bulb
Reversing light, brake lights, tail lights and rear fog
lightP21W
Tu r n s i g n a l sPY21W
Parking lightsW3W
OthersBulb
Side turn signal lightsLED
Licence plate lightC5W
3. Brake lightLED
Entry lightingW5W
front interior lightingC10W
Reading lightsW5W
Rear interior lightingC10W
Luggage compartment lightW5W
Door warning lightC5W
Lighting in storage compar tment on front passenger
sideC3WFig. 240 Front headlight:
Installing the light bulbs
20A5Facelift.book Page 263 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs
264
Positions of the light bulbs in the front headlight ⇒page 263, fig. 240 .
- Front turn signal light
- parking lights and low beam
- main beam light
Removing the headlight
The headlight must be removed in order to change the light bulb of the
parking lights, low beam lights and main beam lights as well as the turn
signal lights.
Removing the headlight
– Switch the ignition and all lights off.
– Open the bonnet ⇒ page 224.
– Unscrew the plastic nut ⇒fig. 241 .
– Pull the fuse in upward direction.
– Pull the locking lever of the headlight as far as the stop in the direction of arrow . – Unplug the plug connector and carefully take out the headlight in the
direction of arrow .
Installation takes place in the reverse order.
Note
We recommend that you have the headlight setting checked by a specialist garage
after installing the headlight.
Turn signal light (at the front)
Changing light bulb for turn signal light (at the front)
– Switch the ignition and all lights off.
– Remove the headlight ⇒page 264.
– Turn the socket in the direction of arrow OPEN (open) and take it out
together with the light bulb for the turn signal light ⇒fig. 242 .
– Press the defective light bulb into the socket, turn to the left and remove.
– Press a new light bulb into the socket and turn the light bulb to the right as far as the stop.
AA
AB
AC
Fig. 241 Front headlight:
Installing the light bulbs
AA
AB
A1
A2
Fig. 242 Removing the light
bulb for the turn signal light
20A5Facelift.book Page 264 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs265
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
– Insert the socket with the changed light bulb into the headlight and
secure it by turning in the direction of arrow CLOSE (close) to the
right.
Note
We recommend that you have the headlight setting checked by a specialist garage
after installing the headlight.
Front parking lights and low beam
Removing the light bulb for the parking light
– Switch the ignition and all lights off.
– Remove the headlight ⇒page 264.
– Remove the protective cap ⇒page 263, fig. 240 .
– Remove the socket ⇒fig. 243 .
– Take the faulty bulb out of the fixture and insert a new one.
– Insert the protective cap. Removing the light bulb for the low beam light
– Switch the ignition and all lights off.
– Remove the headlight ⇒
page 264.
– Remove the protective cap ⇒page 263, fig. 240 .
– Turn the connector with the light bulb up to the stop towards the left and remove ⇒fig. 243.
– Replace the lamp, insert the connector with the new lamp and turn to the right up to the stop.
– Insert the protective cap.
Note
•In order to facilitate the removal of th e bulb for the parking lights, we recom-
mend to remove first of all the bulb for the low beam light.
•We recommend that you have the headli ght setting checked by a specialist
garage after installing the headlight.
Main beam light
– Switch the ignition and all lights off.
Fig. 243 Removing the bulbs
for the parking and low beam
light
AB
AA
AB
AB
Fig. 244 Removing the light
bulb for the main beam light
20A5Facelift.book Page 265 Saturday, September 6, 2008 2:13 PM