maintenance reset SKODA OCTAVIA 2008 2.G / (1Z) Owner's Manual

Instruments and Indicator/Warning Lights17
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Instruments and Indicator/Warning Lights
General view of the instrument cluster
Engine revolutions counter ⇒page 18
Speedometer ⇒page 18
Coolant temperature gauge ⇒page 18
Display
− with counter for distance driven ⇒page 19
− with Service Interval Display ⇒page 20
− with digital clock ⇒page 21
− with Multi-functional indicator* ⇒page 21
− with Information display* ⇒page 26
Button for the selection of the mode (t urn button) / the setting (press button):
− Set hours / minutes
− Activating / deactivating the second speed in mph or km/h* −
Service interval - Display of the rema ining number of days or miles to the
next Inspection Se rvice / Reset* 1)
−Reset trip counter for distance driven
− Resetting Service Interval Display
− Activate / deactivate display mode
Fuel gauge ⇒page 18
Fig. 18 Instrument cluster
A1
A2
A3
A4
A5
1)Valid for countries where the values are indicated in British measuring units.
A6
20A5Facelift.book Page 17 Saturday, September 6, 2008 2:13 PM

Instruments and Indicator/Warning Lights19
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
The following will be displayed in the information display*:
Please refuel! (Please refuel!)
An audible signal sounds as an additional warning signal.
Caution
Never run the fuel tank completely empty! The irregular supply of the fuel system
can lead to irregular running of the engi ne. Unburnt fuel may get into the exhaust
system and damage the catalytic converter.
Note
After filling up, it can occur that during dynamic driving (e.g. numerous curves,
braking, accelerating and climbing a stee p hill) the fuel gauge indicates approx. a
fraction less. When stopping or during less dynamic driving, the correct fuel supply
quantity is indicated. Th is effect is not a fault.
Counter for distance driven
The distance which you have driven with your vehicle is shown in kilometres (km).
In some countries the measur ing unit “mile” is used. Reset button
If you hold the reset button
⇒page 17, fig. 18 pressed for about 1 second, the
trip counter is set back to zero.
Trip counter for distance driven
The trip counter indicates the di stance which you have driven ⇒fig. 19 since this
counter was last reset - in steps of 100 metres or 1/10 of a mile.
Counter for distance driven
The counter for distance driven ⇒fig. 19 indicates the total distance in kilometers
or miles which the vehicle has driven.
Fau lt dis pla y
If there is a fault in the instrument cluster, a constant text will appear in the display
Error . Have the fault rectified as soon as possible by a specialist workshop.
WARNING
Never seek to adjust the trip counter for distance driven while driving for
safety reasons!
Note
If vehicles which are fitted with the info rmation display* the display of the second
speed is activated in mph or km/h, this driving speed is indicated instead of the
counter for the total distance driven.
Fig. 19 Display: Counter for
distance driven
A5
20A5Facelift.book Page 19 Saturday, September 6, 2008 2:13 PM

Instruments and Indicator/Warning Lights23
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Operating with the buttons on the multifunction steering wheel*
Switching over and resetting is performed with the handwheel
⇒fig. 23 .
Selecting the memory
– Short-term pressing of the button allows to select the desired
memory.
Selecting the functions
– By pressing the button , you can call up the menu of the multi-func- tional indicator.
– Turn the handwheel upwards or downwards. In this way, call up in sequence the individual functions of the multi-functional indicator.
– Short-term pressing of the button allows to select the highlighted
function.
Setting function to zero
– Select the memory you want.
– Press the button for more than 1 second.
The following readouts of the selected memo ry will be set to zero with the button
:
•average fuel consumption,
•distance driven,
•average speed,
•Driving time.
You can only operate the multi-functional indicator when the ignition is switched
on. After the ignition is switched on, the fu nction displayed is the one which you last
selected before switching off the ignition.
Outside temperature
The outside temperature appears in the disp lay when the ignition is switched on.
If the outside temperature drops below +4 °C, a snow flake symbol (warning signal
for ice on the road) appears before the temperature indicator ⇒fig. 24 and a
warning signal sounds. After pressing the rocker switch at the windshield wiper
lever ⇒page 22, fig. 22 or the button at the multifunction steering wheel
⇒ fig. 23 , the function shown last is indicated.
Fig. 23 Multi-functional
indicator: Operating with the
buttons on the multifunction
steering wheel
AD
AD
AC
AD
AD
AD
AD
Fig. 24 The outside tempera-
ture
AAAC
20A5Facelift.book Page 23 Saturday, September 6, 2008 2:13 PM

Instruments and Indicator/Warning Lights31
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Lights and Visibility
Here you can set how long the light should
stay on for the function Coming/Leaving
Home and the intensity of the footwell li ghting. Furthermore you can here switch
on or off the function daylight drivin g lights and convenience turn signal.
After selecting the menu point Fac to r y s e tt ing the factory setting is established
again.
Time
Here you can set the time, the time format (12 or 24 hour indicator) and the time
change summer/winter time.
Winter tyres
Here you can set at which speed a warning signal should sound. This function is
used for e.g winter tyres with the permissible maximum speed less than the
maximum speed of the vehicle.
When exceeding the speed, the following is displayed on the information display*:
Snow tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Language
Here you can set in which language the warning and information texts should be
displayed.
Measures
Here you can set the units for temperat ure, consumption and distance driven.
Assistant
Here you can adjust the tones of the acoustic signals of the parking aid*.
Second speed
Here you can switch on the display of the second speed in mph or in km/h
3).
Service
Here you can have the kilomete rs still to be driven and the days until the following
service interval shown and the Service Interval Display reset. Factory Setting
After selecting the menu point
Factory Setting the factory setting of the informa-
tion display is established again.
3)Valid for countries where the values are indicated in British measuring units.
20A5Facelift.book Page 31 Saturday, September 6, 2008 2:13 PM