lock SKODA OCTAVIA 2009 2.G / (1Z) Columbus Navigation System Manual

General information
4Information on how to operate the navigation systemThe requirements of today's road traffic demand the driver’s full concentration at all times. Apart from the availability entertainmen
t, the extensive and demanding equipment
details of this system also offer a wide range of information, which will help you to reach your destination quickly and safely. But you should only operate the navigation system with its wide range of possi- bilities when the traf
fic situatio
n allows.
The volume settings must be selected in
such a way that audible signals from the
outside, e.g. a Martins horn from utility
vehicles (police cars, ambulances and fire
brigade), can be heard at all times.
WARNING
Please concentrate fully at all times on yo
ur driving! As the driver you are fully
responsible for road safety. Only use the functions in such a way that you are always in full control of your vehicle in all traffic situations!Before using the navigation system•
Please observe the respective traffic regulations when driving.
•
Street and location names can be changed.
It is therefore possible that, in excep-
tional cases, the names stored on the na
vigation DVDs do not correspond to the
changed names.•
The route calculated by the navigation
system is a recommendation for reaching
the intended destination. While driving please pay attention to traffic lights, one-way streets, lane change restrictions, canals and ferries.
WARNING
Road traffic legislation (StVO) applies at
all times, even if a driving recommen-
dation contradicts the StVO.
Caution
•
Inserting a second CD/DVD while a CD/D
VD is being ejected can destroy the
CD/DVD drive in the unit. Please note that
the CD/DVD ejection lasts a few seconds
after pressing the
Eject key
. During this time the lock
in front of the CD/DVD case
is open. It is essential that
you wait until the CD/DVD has
been fully ejected before you
try to insert a new CD/DVD.•
Press the buttons and the keys of the unit gently in order to avoid damaging them.
Gentle pressure on the appropriate key is sufficient to operate the unit. Please note that the control buttons have predetermined breaking points, in order to reduce the risk of injury.•
Do not use any pointed or sharp-edged objects to operate the touch-screen. Slight
finger pressure sufficient to operate the equipment. A display on the screen, which cannot be called up by pressing the button,
is therefore not available at that time.
•
Please note that a dirty or scratched na
vigation DVD can cons
iderably impair the
speed and the functions of
the navigation system.
Note
•
Your navigation system is a high-powered
computer. Just as your computer at
home, this unit needs a few seconds for proc
essing complicated control sequences. In
such a case it is possible that the unit wi
ll no longer react when operated from the
outside until the triggered processes have
been dealt with processed in the back-
ground. Please be patient, as it is quite po
ssible that the unit “stores” the carried-out
operating steps even if it does not appear to react to the operation from the outside. These operating steps are processed one after the other by the unit once the processes in the background have been completed, which can be confusing.•
The DVD drive installed into this unit uses a Dolby Digital
® Audio coding system
and MLP Lossless
® for highest reproduction quality even with standard Audio DVDs.
“Dolby
®”, “MLP Lossless
®” and the Double-D-Symbol are trademarks of Dolby Labo-
ratories
®.
•
With the help of “DTS
®” and “DTS 2.0
®” the surrounding sound of a DVD is trans-
formed and replayed in best stereo quality. “DTS
®” and “DTS 2.0
®” are registered
trademarks of DTS, Inc.•
WMA audio data (Windows Media Audio) can also be replayed by the unit and
stored on the hard disk (HDD) providing
this has not been protected by the DRM
š
s32k.a.book Page 4 Friday, September 18, 2009 1:54 PM

General information
8With some of the menus you can enter a fr
ee text. For instance, when allocating a
folder name for storing MP3 data on the hard
disk or when searching for the name of
a special destination. – Press to accept a character sequence offered by the system or press to
delete the characters in the entry line.
– When in the entry window, press on a character shown on the keypad block to
accept it into the entry line.
– You can also delete or change the charac
ter sequence in the entry line as well as
insert additional characters.
– Press to accept the indicated character sequence in the entry line. By pressing
the input mask will be closed
without the entries being accepted.
Further input possibilities: - changes from upper case to lower case and vice versa. - opens the input mask for digits and special characters. The function key changes
to . Press , to change again to the letter input mask.
- space key for entering spaces. or - moves the character entry cursor (the cursor) in the entry line to the left or right.
- deletes characters in the entry line starting from the position of the character
entry cursor from right to left. Selecting letters based on specific characters Some letters in the input masks are also marked with a small triangle “
a”. This indi-
cates that specific characters based on this letter can be selected. Continue to press down on the correspondin
g function key with
your finger until a
pop-up window with these specific characte
rs can be displayed. Press to accept the
desired character into the entry line - the po
p-up window will close. If no entries are
entered, the pop-up window will clos
e automatically after a few seconds.
Some specific characters can be “written ou
t”. The navigation system will also recog-
nise the character sequence “AE”, “UE” and
“OE” instead of the German specific char-
acters “Ä”, “Ü” and “Ö” vom Navigationssystem erkannt. Other specific characters can
be ignored, for example instead of “É”, “Ê” or
“È” a normal “E” will be accepted by the
navigation system.Input mask for digit entry– Press to accept an indicated character sequence or press , to delete the
characters in the entry line from right to left.
– Press one of the to function keys
in the input mask to accept the corre-
sponding digit into the entry line.
– Press when the correct number is indicated in the entry line. By pressing
the input mask will be closed wi
thout the entries being accepted.
Special functions* Parking aid If your vehicle is equi
pped with “parking aid” and after
it is activated, the distance to
the obstacle is shown on the screen.
OK

OK
y
:;A-Z
A-Z
‚
b

Fig. 4 Input mask for digit entry
OK

0
9
OK
y
s32k.a.book Page 8 Friday, September 18, 2009 1:54 PM

General information
9
Climatronic If your vehicle is equipped with climatronic, a feedback is received on the screen when changing the settings. Display of time You can switch the display of the time on or off in the menu
Setup System
.
Switching the system on and off– The system is switched on or off by pressing the control button . The last active audio source before switching off is repeated. If the key is pulled out of the ignition lock while the unit is switched on, the unit will switch off automatically. You can then switch the unit on again. If the
ignition is switched off, the unit (discharge
protection of the vehicle battery) switches
off automatically after approx. one hour.
This process can be repeated as often as necessary.Anti-theft protectionThe anti-theft coding of your navigation sy
stem prevents an operation of the system
after a voltage interruption, e.g. during a vehicle repair or after theft. After discon-necting the battery, disconnecting the navigati
on system from the on-board voltage of
the vehicle and after a fuse failure, the code
must be entered before the vehicle can be
used again.Enter code– If a keypad appears after switching on
with the command to enter the code, the
unit can be unlocked by entering the corr
ect four-digit code number. The number
of the possible attempts is shown in the second touch-screen line.
– Press a digit from to on the digit block displayed on the screen. The digit is
accepted in the entry line.
– After a four-digit order has been entered, the group of digits will turn grey (inactive)
and no further digits can be accepted in the entry line.
– Press on the touch-screen to erase the digits in the entry line from right to left
and thereby correct your input, if necessary.
– If the correct code number is di
splayed in the entry line, press .
Code number The code number can only be called up “onlin
e” via the Škoda system, as this guaran-
tees even more effective anti-theft protec
tion. Please contact your Škoda dealer if
necessary. Incorrect code number If an incorrect code is confirmed after entry
of the code, the procedure can be repeated
once again
. The number of possible attempts is
shown in the second line on the
touch-screen. If the code number is entered incorrectly fo
r the second time, the unit will be blocked
for approx. one hour. It is possible to ente
r again the safety code
after one hour has
expired, when the unit and the ig
nition have been switched on.
If two invalid attempts are then made agai
n, the navigation syst
em will be blocked
again for an hour. The cycle - two attempts, blocked for
an hour - will continue to apply.
Note
The code is normally stored in the instrument
cluster. This ensures that it is automati-
cally decoded (convenience coding). Ma
nual input of the code is normally not
necessary.
A1
0
9

OK
s32k.a.book Page 9 Friday, September 18, 2009 1:54 PM

Range selector key MEDIA
20Range selector key MEDIAGeneral information for CD/DVD operationAudio-CDs (CD-A) and Audio-DVDs, MP3-CDs and MP3-DVDs as well as Video-DVDs can be played in the internal CD/DVD drive. CD not legible If the unit cannot read
an inserted CD/DVD, “
CD fault will be displayed for a short
period of time. Please check CD.
” or “
Wrong data format. Data cannot be read.
”
and the CD/DVD is reinserted into the initial position after a few seconds. If the CD/DVD is not taken out within 10 seconds, it is drawn in again for safety reasons.
WARNING
•
The CD player is a 1st class laser product. There is a definite risk of injury
from invisible laser beams if it is opened.•
The CD player contains no parts that ha
ve to be serviced or repaired. Please
contact your specialist garage if a mechan
ica l d e fe c t o ccurs o r t he CD pl a ye r ha s
to be repaired.
Caution
•
Inserting a second CD/DVD while a CD/D
VD is being ejected can destroy the
CD/DVD drive in the unit. Please note that the CD/DVD ejection lasts a few seconds after pressing the
Eject key
. During this time the lock in front of the CD/DVD case
is open. It is essential that you wait until
the CD/DVD has been fully ejected before you
try to insert a new CD/DVD.•
If the CD/DVD drive becomes mechanically defective or a CD/DVD has been
inserted incorrectly or not fully, first of all “
CD fault will be displayed on the touch-
screen. Please check CD.
” and then the “
DVD drive fault
” indicated on the touch-
screen. Please check the CD/DVD and place it again correctly and fully into the drive. If a “ DVD drive fault
” is indicated again,
please contact your Škoda Service Partner.
•
If the inside temperature of the unit is t
oo high, no CDs or DVDs will be accepted.
The unit switches into the last active operating mode.
Note
•
If the function key is inactive, no ne
w Audio CD/DVD has been inserted or an
inserted Audio CD/DVD is not readable.•
It is possible that CDs/DVDs protected
by copyright and non-original CD-R, CD-
RW and DVD-RWs are not returned at all or only in certain circumstances.•
WMA audio data (Windows Media Audio) can also be replayed by the unit and
stored on the hard disk (HDD) providing
this has not been protected by the DRM
procedure copyright (Digital Rights Manage
ment). The operation and behaviour of the
unit complies with the MP3
compressed audio data and are not described further.
•
Please observe the following information for the MP3 operation
⇒page 24.
•
Please comply with the national legal
copyright requirements in your country.
•
The DVD drive installed into this unit uses a Dolby Digital
® Audio coding system
and MLP Lossless
® for highest reproduction quality even with standard Audio DVDs.
“Dolby
®”, “MLP Lossless
®” and the Double-D-Symbol are trademarks of Dolby Labo-
ratories
®.
•
With the help of “DTS
®” and “DTS 2.0
®” the surrounding sound of a DVD is trans-
formed and replayed in best stereo quality. “DTS
®” and “DTS 2.0
®” are registered
trademarks of DTS, Inc.
š
CD
s32k.a.book Page 20 Friday, September 18, 2009 1:54 PM

Range selector key MEDIA
22
- changes over to the TV mode when a TV Tuner* is connected
⇒page 30.
- changes over to a Video-DVD inserted into the internal CD/DVD drive
⇒ page 28. Additional function keys in the AUDIO menu
- changes over into the
DVD menu
and plays the last selected video source.
- opens a pop-up window in which the repeat function determines whether
the or the (in audio CD operation) respectively the current (in the MP3 operation
⇒page 24) should be repeated.
- opens a pop-up window in which the random play function
Mix
or the auto-
matic play
Scan
, the capacity of the hard disk
HDD capacity
or Switch off display
can
be selected.
- opens the title list of the current audio source in order to select another title
or audio source. Additional function keys in the DVD menu
- changes to the
Audio menu
and plays the last selected audio source.
- switches over the DVD played in the internal CD/DVD drive to the menu selec-
tion of the film and also opens the incorporated menu control.
- opens a set-up menu to adapt the display set-ups for the current film. - opens the chapter selection for the DVD played in the internal CD/DVD
drive.Inserting or ejecting a CD/DVDInserting a CD/DVD– Push a CD/DVD with the written side facing up as far as possible into the CD/DVD
case until it is automatically drawn in. Th
e play function will start automatically.
Ejecting a CD/DVD– Press the button to move the CD/DVD
in the internal CD/DVD drive into the
eject position.
If a CD/DVD is not removed when ejected, it will be reinserted after approximately ten seconds for safety reasons. Pl ayable MP3 a nd WMA data ca n als o be stored o n the hard di sk of the unit
⇒page 27.
WMA Data (Windows Media Audio) The copyright of audio data compressed by
Windows
Media
Audio, can also be
protected by the DRM procedure (
Digital
Rights
Management). Such WMA data is not
supported by the unit.Inserting or removing a memory card Inserting a memory card– Push the memory card into the memory ca
rd case with the trimmed edge to the
front right (horizontal case) or to the front top (vertical case), until it is locked in position. The play function
will start automatically.
Taking out a memory card– Press against the spring resistance of the inserted memory card, the memory card
“skips” back into
the Eject position.
Destination entry from the memory card– You can enter the destinations from the SD card using the function
in the
Navigation menu
. The destinations must only be stored
on the SD card in the corresponding format.
Only MP3 data and unprotected WMA data can
b e re a d f ro m t h e S D c a rd . A l l o t h e r d a t a
is ignored. Pl ayable MP3 a nd WMA data ca n als o be stored o n the hard di sk of the unit
⇒page 27.
Memory card empty or data not readable If a memory card is inserted, on which no audio data has been stored, it will
not
be
switched over into the memory card mode
after the loading procedure. When in the
Audio menu
the function key remains inactive on the top line of the touch-screen
and the function cannot be seleced
⇒page 21, fig. 8
.
TVDVDVideoRepeat
titel
CD
folder
ExtrasSelect.AudioMenuDisplayChapter
š
Import destinations
SD
s32k.a.book Page 22 Friday, September 18, 2009 1:54 PM

Range selector key MEDIA
27
Store and edit audio data (HDD)Store MP3 and WMA data on the hard disk (HDD)Select titles or folders to be saved– Check the available audio sources for titles
or folders which you may wish to store
on the hard disk. You can also select the
complete contents of an installed data
carrier for storing on the hard disk in th
e selection window of
the available audio
sources.
– If you press on the function key behind the display of a title or folder, a pop-up
window will open.
– Pressing in the pop-up window
will start the play function.
– Press in the pop-up window to store the respective title or folder on the hard
disk.
– Press in the following pop-up wind
ow for confirmation that you have
taken note of the message.
Select memory space and save titles– Press , if the title or folder should be saved directly on the first level,
which is the root folder of the hard disk.
– Or press if a new folder should be created for the title or folder. Choose
a name for this folder from the following menu. The newly created folder is opened and the name you choose will be indicated in the title line.
– You can now create another folder (o
ne folder has a maximum of seven sub-
folders) or you can save the selected title or folder in the currently described folder. Press the function key to open the
appropriate higher
priority folder.
– Press the function key if you wish to save the title or folder at the
selected point.
– Press to cancel the saving process of the currently stored title. Once the
saving process has been completed, the
pop-up window will close automatically.
Saving 100 music titles of average length of time (3 - 5 minutes) will take approximately 40 minutes.
If the unit is switched off during the saving
process, the saving process will be termi-
nated with the last fully saved title. Functions and progress display during the memory procedure You can continue listening to
this or another audio source while storing other audio
data. Data names with a length of max.
32 characters can be displayed.
The function key is blocked in the
Audio menu
during the memory procedure.
If the function key is pressed regardless, a pop-up window will open instead of the selection menu where the progress of the
saving process is displayed. If you press
in the pop-up window, the storing proces
s will be cancelled with the last fully
stored title. Press the range selector key twice to close the pop-up window and continue the storing process.Edit stored audio data (titles) and foldersSelect title or folder– Open the selection menu of
the available audio sources
⇒page 23.
– Press on the function key to display the stored titles and folders on the hard
disk.
– Select the title or folder to be processed. Press on the display of a folder
to open it. Press the function key to open the appropriate higher priority folder. The names of the currently opened folders are displayed in the title line.
– Press the function key behind the display of the title or folder you wish to
process. A pop-up window will open.
– The play function can be started and the
title or folder can be copied, renamed or
erased via the pop-up window.
Function keys in the pop-up window:
- starts the play function of
the selected title or folder.
- stores a copy of the title or folder
⇒page 27, “Select memory space and save
titles”.
- opens the input mask to change the title or folder name.
H
PlayCopyContinueEnter file/folderNew folder
FEnter file/folder
Cancel
Select.Select.
Cancel
MEDIA
J HDD
G... Name
F
H
PlayCopyRename
s32k.a.book Page 27 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
36– Press the range selector key . The last
opened menu in the navigation will be
displayed.
– Press on the range selector
key again if the main menu
Navigation

⇒ page 35, fig. 14
has not been displayed.
and set - opens a window with information about your current location. When in this
menu you can store the displayed location by pressing in the destination memory. - stores the current position as “Flagd
est.” in the destination memory. Only one
destination can be stored in the destinatio
n memory under “Flagdest.”. If the flagged
destination is not renamed, it is overwritten by renewed pressing of . Further function keys in the main menu Navigation
- opens a selection menu to select the type of destination entry.
•
- used for the entry of a new destination.
- opens a pop-up window:
•
- for selecting an already stored travel destination.
•
- in order to store the displayed travel destination in the main
menu
Navigation
.
•
- switches over to the destination memory.
•
used for the display of the destination imported into the
memory from the SD card
- opens a pop-up window during route guidance:
•
- uses the direction arrows to disp
lay a list with turning points still
to be driven during route guidance.•
- used for the manual entry of a congestion ahead and the
recommendation of the next available route•
- used for manual entry of ce
rtain sections of the route
which are blocked.•
- displays a list with street names or street descriptions of those parts of
the journey still to be driven during route guidance.•
- to cancel manually a route block.
- opens a pop-up window:
•
- for changing over into the tour mode if more than two destinations
still have be driven during route guidance.•
- for entering an additional destination which must still
be driven during route guidance.•
- used for route guidance close to the entered stopover.
•
- used for route guidance to an exactly determined stopover.
•
- used for switching over into the
waypoint nav. if
in non-digitalised
areas, specific points are set (Offroad Navigation).
- starts the route guidance to the displayed travel destination.
Determine parameters for the route calculation The menu
Route options
⇒fig. 15
is called up by pressing in the main
menu
Navigation
⇒page 35, fig. 14
. The menu
Route options
is used to determine
the criteria according to which a route is to
be calculated and what types of destination
you wish to allow for the route calculation. The changes in the menu
Route options
must be confirmed with , as they cannot
be taken over otherwise.
- opens a pop-up window:
Fig. 15 Select route option.
NAVNAV
Position
$
Position
Store
$
$
New dest.
New dest.
Memory
Load destinationSave destination
Edit memoryImport destination
Route
Manoeuvre listCongestion aheadManage blocked routesRoute listRemove exclusion
Extras
To u r m o d eEnter stopover destinationClose toExactlyWaypoint nav.
Start
Route options
OK
 Route
s32k.a.book Page 36 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
40
- Move a crosshair to choos
e a point on the map in the
surrounding area where you intend to search for a point of interest. Proceed as described in chapter “Select travel destination from the map”.
- During current route guidance the
search for a point of interest is
limited to the surrounding area of the calculated route. Further options for POI search
- You can search for a particular point of interest by entering a name.
- You can search for a particular point of interest by entering a phone number.
Please enter only the phone number,
without a city or country code.
Select travel destination from the map
– In the menu
New dest.
, press on the function key . The last travel destina-
tion for which route guidance was started will be shown in the map display. If no travel destination was arrived at, the curren
t location will be displayed in an over-
view map.
– Turn button to zoom in and out of the map and/or to change the map scale.
Press the function key or .
– Keep pressing on the map display and do not stop. The crosshair will follow your
movements. If you move the crosshair to
the edge of the screen, the adjoining map
section will appear after a few seconds. The geo-position (position display via coordinates) or the street name for the
current position of the crosshair will be
displayed at the top of the touchscreen.
– If the desired travel destination or destination area is displayed, press the function
key . Route guidance will start automatically.
– Press on the function key , if initially you only wish to store the displayed
destination.
Determining a map destination more accurately You can further restrict a travel destination selected from the map display later on in the menu
Address entry
. For this purpose press the range selector key after the
start of route guidance to change from the map display to the main menu
Navigation
.
Here you can press the function key to
terminate route guidance. If you now
change into the menu
Address entry
, the travel destination selected in the map will be
displayed in the form of an address and can be determined there more precisely. On the other hand
you can use the menu
Address entry
to determine the area to be
displayed in the map display as a destination selection. Further function keys in the map display - briefly switches the map display to the
overview display (large scale). After a few
seconds it will switch
back automatically to the last
selected zoom display (smaller
scale).
- opens a menu for entering a travel destination via its coordinates. - saves the travel destination selected from the map in the destination
memory.
Entering a travel destination via coordinates
– In the menu
New dest.
, press on the function key .
– Press the function key on the map disp
lay. The coordinates of the last travel
destination for which a route guidance was started are displayed. If no travel desti- nation was approached, the coordinates of
the current location will be displayed.
– Press the function key or
to open the corresponding input
mask.
– By pressing on and , you can move the character entry cursor within the input
fields or change to the next input field.
– When in the input mask, press on a character shown in the keypad block to accept
it behind the character input cursor. Ex
isting characters will be overwritten.
– Press on if the desired latitude or longitude is displayed in the entry fields. – Pressing , will erase characters from right
to left as of the position of the char-
acter input cursor. By pressing the input mask will be closed without the entries being accepted.
If the entered coordinates are outside the stored navigation area, a pop-up window will open with the following information: “
These GPS coordinates cannot be
Select point on the mapAlong the routeName withTe l .Map/GPS
Map/GPS
A8
ˆ
}
OK
Save
NAV
Stop
/GPSSaveMap/GPS
Map/GPS
GPSLatitude
Longitude
‚
b
OK
y
s32k.a.book Page 40 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
50– Press the range selector key in the
map display to insert the split-screen.
– Press the function key at the top left in the split-screen. – In the pop-up window press on to
display the direction arrows in the
split-screen
⇒page 49, fig. 22
.
– Press on in the pop-up window to
display an overview map in the split-
screen with the starting and finishing point.
Press briefly on this map to change its
type of display.
– Press the function key or the range selector key to close the split-screen. Route guidance tour plan When driving to a tour plan, route guidance
will start automatically to the next desti-
nation after reaching a stopover. If an exac
t stopover cannot be reached, it must be
deleted from the tour plan before route guidance continues to the next destination. If route guidance to the next destination has been started manually, only this destination will be approached and all further dest
inations of the tour
plan are ignored.
Note
•
If you have missed a turn-o
ff during route guidance an
d there is no other opportu-
nity to turn at that moment,
continue driving until the navi
gation system offers you an
alternative route.•
The quality of the messages transmitted by the unit depends on the available navi-
gation data and, during traffic problems, also
on the available traffic reports. The radio
stations broadcasting the traffic reports are responsible for the content and quality of the available traffic reports.Dynamic route guidance with TMC use Switching the dynamic navigation on or off– In the main menu
Navigation
press on the function key .
– In the map display, press on or on
⇒page 49, fig. 21
during
a route guidance and on in the pop-up window.
– In the menu
Route options
, press on the function key and select
the desired set-up by pressing yo
ur choice in the pop-up window.
– Press to confirm your input. Traffic problems received via TMC which affect the route are displayed in the map by means of a coloured symbol. Traffic proble
ms, which do not affect the route, are
displayed in the map by means of a grey
symbol. The direction in which a traffic
problem is found, is displayed by means of an arrow in the symbol. The duration of a traffic problem on the route is displayed
in the map by means of continuous PKW
(motor car) symbols
.
 Dynamic route
b Off
When the dynamic navigation is
switched off you will not be advised of traffic prob-
lems affecting your route duri
ng route guidance and you are not directed away from or
through the traffic problems. TMC traffic reports are updated automatically in the unit ⇒ page 51, “Requirements for a dynamic rout
e guidance” and displayed by pressing
the range selector key . If one of the announced traffi
c problems is on your route,
you can also switch on the
dynamic route guidance during the current
route guidance or block the route manually
⇒ page 52, “Manually blocking a stretch of the route”. Dynamic route
b Manual
If the dynamic navi
gation is set to
manual
and you are in route guidance mode you
can select to avoid the announced traffic problems on your route
⇒page 51,
“Requirements for a dynamic route guidance”. If the navigation system is alerted of a tr
affic problem on the calculated route, the
driver will be notified of this by means
of an audible message and information in a
pop-up window. The expected delay incurred in avoiding this traffic problem and the length of the alter- native route will be displayed. The expected time lost when driving through this traffic problem will also be displayed.•
Press to remain on the calculated route and to pass through the
traffic problem.•
Press on for an alternative route to
be calculated taking
into account the
announced traffic problem.
MAP
NAV symbol
Overview
O
MAP
Options
Navigation
 ... /...
Route options
 Dynamic route
OK
TMC
Current routeBypass
s32k.a.book Page 50 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
51
 Dynamic route
b Automatic
If the dynamic navigati
on system is set to
Automatic
and you are in route guidance
mode, you will automatically be guided around the announced traffic problem on your route
⇒page 51, “Requirements for a dynamic route guidance”.
After input of relevant traffic information
for your route you wi
ll be advised of the
change in the current route guidance by mean
s of an acoustic message. You will auto-
matically be guided around an
nounced traffic jams or blocked roads, if this saves time.
Such announcements will take place if a traf
fic problem affects the
original route calcu-
lation, the traffic problem has been solved and the navigation system can see only one possibility of driving the actually most advantagous route. Requirements for a dynamic route guidance TMC (Traffic Message Channel) is a digital radio data service for
continuous
transmis-
sion of traffic information. The unit has a continuous background of TM
C traffic reports providing a TMC station
at the current location can be received. The quality of the transmitted traffic reports depends on the broadcast editing carried out by the radio station. The reception of
the TMC traffic reports cannot be switched
on or off. The station you are listening to does not have to be a TMC station.TMC traffic reports can only be evaluated an
d displayed by the uni
t if the navigation
data for the currently driven area is stored
in the unit memory or can be called up via
an inserted navigation DVD. The current TMC traffic reports can be disp
layed by pressing the range selector key
.Note
•
There may not be any advantage in avoiding the traffic jam if, as a result of the TMC
traffic reports, the diversio
n is also heavily congested.
•
You can manually block the information for th
e route in front of you if traffic prob-
lems ahead have not yet been included in the TMC traffic reports
⇒page 52.
Fade in route or manoeuvre listThe route or manoeuvre list can only
be displayed during a route guidance.
Split-screen in the map display– Press the range selector key in the map display to open the split-screen. – Press on the function key on the top left in the split-screen and on
in the pop-up window. The ma
noeuvre will be displayed
⇒fig. 23
. The route list
can only be called up via the main menu
Navigation
.
Main menu Navigation– You can open the main menu
Navigation
during route guidan
ce by pressing the
range selector key .
– Press on the function key in the main menu
Navigation
and on or
in the pop-up window.
In the
Manoeuvre list
the turning points still to be pa
ssed will be displayed in the list
by means of direction arrows. Street name or street description refers to the street into which to turn
⇒fig. 23
.
In the
Route list
the street names or street descriptions for the parts of the journey still
to be driven are displayed in a list.
TMC
BAT-20H647
Fig. 23 Manoeuvre list in the map display.
MAP
Manoeuvre list
NAV
Route
Route list
Manoeuvre list
s32k.a.book Page 51 Friday, September 18, 2009 1:54 PM