stop start SKODA OCTAVIA TOUR 2007 1.G / (1U) Owner's Manual
[x] Cancel search | Manufacturer: SKODA, Model Year: 2007, Model line: OCTAVIA TOUR, Model: SKODA OCTAVIA TOUR 2007 1.G / (1U)Pages: 205
Page 42 of 205
41
CONTROLS AND EQUIPMENT
Information for drivingStarting engineThe engine can only be started if the selector
lever is in position „N“ or „P“ - see page 44.Selecting a forward gear
Always first of all depress the brake pe-
dal before selecting a forward gear when
the vehicle is stationary and the engine
is running.
Do not depress the accelerator when
moving the selector lever if the car is sta-
tionary.
If you inadvertently move the gearshift
lever into position „N“ when driving, you
first of all have to release the accelera-
tor and wait until the engine is running
at idle speed before again engaging a
forward gear. Warning
When the engine is idling and the car
is stationary (e.g. at traffic lights or
when stopped in congested traffic)
it is always necessary to depress the
brake pedal in order to hold the ve-
hicle no matter the selector lever po-
sition, because the power transmis-
sion is not fully interrupted even
when the engine is idling and the car
may creep forward.
If a forward gear is engaged when the
vehicle is stationary, on no account
inadvertently operate the throttle
(e.g. by hand from the engine com-
partment) otherwise the car will im-
mediately move forward - this may
also happen even if the handbrake is
properly applied.
Move selector lever into position „P“
and apply the handbrake before car-
rying out any work on the running
engine.
Driving off
Select a gear (
R, D , 3 , 2 , 1 ). Wait until the
gearbox has shifted into gear and the
power is transmitted to the driven wheels
(can be felt from a slight engagement jolt)
before then pressing the accelerator.
Coming to a stop
You do not have to move the selector lever
to position „N“ if stopped only for a short
time, e.g. at traffic lights. It is sufficient to
hold the car with the brake. The engine
must only be running at idling speed, how-
ever.
Parking
On the flat it is sufficient to engage the Park
lock. If parked on a downhill stretch, first of
all apply the handbrake fully and then en-
gage the Park lock. Doing this ensures that
there is no excessive stress acting on the
Park lock mechanism and the Park lock can
be more easily released.
Warning
When the car is parked, the selector
lever should always be moved into
position „P“ for only this position
prevents the car moving off by itself.
Page 43 of 205
42CONTROLS AND EQUIPMENTTow-starting
If your car is fitted with an automatic gear-
box, it is not possible to start the engine by
tow-starting or pushing the car - see page
178.
If the battery is discharged, jump-starting
cables can be used for connecting the bat-
tery of another car to start the engine - see
page 177.
Towing car
It is essential to refer to the information on
page 179 if it is necessary to tow in the car.
Drive programsThe automatic gearbox features various dri-
ve programs. Depending on your style of
driving or the driving situation, an econo-
my , in other words consumption-oriented
program, or a sport program is selected.
The program is selected automatically
depending on how the accelerator pedal is
operated.
If the accelerator pedal is depressed slow-
ly , the gearbox selects the economy pro-
gram. This of fers improved fuel economy .
If the accelerator pedal is depressed rap-
idly , the gearbox selects the sport program. Kickdown
The kickdown facility makes it possible to
achieve maximum acceleration. If the ac-
celerator pedal is depressed as far as the
stop, the automatic gearbox shifts down into
a lower gear in line with the speed of the
car and of the engine. The gearbox waits
until engine speed has reached the maxi-
mum specified speed in each case before
shifting up into the next higher gear.
Page 44 of 205
43
CONTROLS AND EQUIPMENT
Adjustable steering columnThe steering column can be adjusted for
angle and length.
First of all, properly adjust the driver’s seat.
Swivel lever below steering column down
as far as the stop.
Adjust the angle and length of the steer-
ing wheel to suit your body proportions.
Push the lever back up again - toward
the steering column.
Warning
The steering column must not be ad-
justed when driving.
For safety reasons, the lever must al-
ways be pressed firmly up again so
that the steering wheel cannot move
while the vehicle is in motion.
Ignition lockPetrol engines1 - Ignition off, engine off
2 - Ignition on
3 - Starting engineDiesel engines1 - Fuel supply cut off, engine off
2 - Preglow (ignition off)
Do not switch on any large current consum-
ers when heating the glow plugs to prevent
draining the battery unnecessarily.
3 - Starting engine
Emergency programIf a fault develops in the gearbox electron-
ics, emergency programs are activated de-
pending on the type of fault.
The gearbox does continue to shift au-
tomatically but more severe shift jolts can
be felt in this case. You should drive the
car to the nearest Škoda Dealer.
The gearbox no longer shifts automati-
cally.
In this case, the gearbox can still be shifted
manually but only 3rd gear is available in the
selector lever positions „D“ , „3“ and „2“.
1st gear and Reverse gear are available as
usual when the selector lever is moved into
positions „1“ and „R“.
However, the torque converter has to per-
form more work, particularly because 2nd
gear is no longer available. In such cases,
it is possible that the gear oil may become
too warm.
It is therefore necessary to drive the car
immediately to a Škoda Dealer.
Page 45 of 205
44CONTROLS AND EQUIPMENTFor all models:Position 1
To lock the steering wheel , withdraw key
and turn wheel until you hear the locking
pin engage.
Warning
Do not withdraw key from lock until
vehicle is stationary! The steering
lock might otherwise unintentionally
engaged.
Note
If you forget to switch off the side lights or
a turn signal light, an audible signal will
sound after you switch off the ignition or
withdraw the key and then open the driv-
er’s door.
Position 2
If the key is difficult to turn in the lock or
cannot be turned to this position at all, move
the steering wheel back and forward slightly
to release the locking pin. Warning
If the vehicle is allowed to roll, the
ignition key must be in position 2 in
the lock - ignition on. This position
is also indicated by the warning
lights coming on. Failure to turn the
ignition key into this position can
result in the steering locking uninten-
tionally.
Do not withdraw the ignition key un-
til after the vehicle has come to a stop
and has been properly secured to
prevent it moving by applying the
handbrake or engaging a gear.
Position 3
The starter is operated when the key is
turned into this position. The ignition key
must be turned back each time into posi-
tion „1“ before again attempting to start the
engine. The starter repeat lockout in the ig-
nition lock prevents the starter again being
operated when engine is already running.
When the key is in this position, the main/
low beam headlights and other major elec-
trical components which are on, are then
switched off.
The starter may only be operated (ignition
key position 3), if the engine is not run-
ning. If the starter is immediately operated
after switching off the engine, the starter
or the engine can be damaged.
Starting engineGeneral notesWarning
Never run the engine in non-venti-
lated or enclosed areas, the exhaust
gases of the engine contain besides
the odourless and colourless carbon
monoxide a poisonous gas - hazard!
Carbon monoxide can cause uncon-
sciousness and death.
Never leave your vehicle unattended
with the engine running.
Before starting, move gear lever into
Neutral (selector lever of automatic gear-
box into position „P“ or „N“ ) and apply
handbrake firmly.
On models with a manual gearbox, de-
press the clutch pedal when operating
starter so that the starter only has to crank
the engine.
As soon as engine starts, release igni-
tion key immediately - otherwise the starter
may suffer damage.
After starting a cold engine, it may sound
noisy for a moment or two because the oil
pressure has to build up in the hydraulic
tappets first.
Do not warm engine up by running it with vehicle stationary. Drive off
straight away.
Page 47 of 205
46CONTROLS AND EQUIPMENTIf the engine does not start, once again pre-
heat and start once again as described. If
the engine still does not fire, the fuse for
the diesel glow plug system may have
blown - see page 167.
Contact your Škoda Dealer.
Starting a warm engine
If the engine is already at operating tem-
perature when started, the glow warning
lamp does not come on - the engine can
be started straightaway.
Switching off engineDo not switch off the engine immediately
after operating it for a lengthy period at
high engine loads, but allow it to run at
idling speed for about 2 minutes to avoid
any build-up of heat.Warning
Never switch off the engine before
the vehicle is stationary - risk of ac-
cident!
The brake booster only operates
when the engine is running. Greater
physical effort for braking is required
when engine is switched off. Be-
cause if you do not stop as normal,
this can cause an accident and se-
vere injuries.
After the ignition has been switched
off, the fan may continue running for
a while (up to about 10 minutes) with
the ignition switched off. It may also
start to run again suddenly after a
short time if
- the coolant temperature increases
due to heat build-up
- when engine is warm and the en-
gine compartment is heated addi-
tionally by strong sunlight.
Special care must therefore be taken
when working in the engine compart-
ment!
Audible signalsThe status of certain systems is indicated
by an audible signal sounding; refer to the
chapters on:
- Audible signal when reversing - page 47
- Excess speed signal - page 47
- Warning lamp - page 56
- Information display - page 53
- Switch - page 62.
The audible signal may also sound when
using a car radio - see operating instruc-
tions of the radio.
Page 62 of 205
61
CONTROLS AND EQUIPMENT
Electronic differential lock (EDL)*The EDL system operates in combination
with the ABS. A failure of the EDL system
is indicated by the ABS warning light co-
ming on. You should then contact a Škoda
Dealer without delay.
Models fitted with ESP are equipped with
electronic differential lock (EDL).
If a major fault is present in the ABS sy-
stem, an audible warning signal also
sounds (3 peeps). Further information on
the ABS and EDL systems is given on
pages 122 and 124.Electronic immobiliserWhen the ignition is switched on, a data
harmonization is performed between key
and control unit. If the data exchanged are
correct, this is confirmed by the warning li-
ght coming on for a few seconds.
If an unauthorized car key (e.g. forged key)
has been used, the warning light changes
to a continuous flashing light. It is then no
longer possible to start the car - see page
7.
Brake fluid levelThe warning light comes on for a few se-
conds after switching on the ignition.Warning
If the warning light comes on when
the ignition is switched on or when
driving, there is a fault in the brake
system. Contact the nearest Škoda
Dealer without delay and have the
brake system inspected.
An audible warning signal sounds
(3 peeps).
You can drive on carefully to the near-
est Škoda Dealer but allow for higher
pedal pressures, longer braking dis-
tances and greater idle travel of the
brake pedal.
The warning light also comes on when the
handbrake is applied.
Charge indicatorThe warning light comes on when the igni-
tion is switched on. It should go out when
the engine is started.
If the warning light comes on when driving
or does not go out after the engine has
started, stop the car and switch off the
engine. Check the ribbed belt.
If it is loose or broken, do not drive any
further . The belt has to be tensioned or
replaced.
If the ribbed belt is in proper order and the
warning light nevertheless comes on, it is
possible to drive on to the nearest Škoda
Dealer. In this case, the battery will not be
charged; switch off all unnecessary elec-
trical components in the vehicle.
An audible warning signal sounds (single
peep signal).Seat belt warning system*This warning light comes on to request the
driver to fasten the seat belt.
If the driver’s belt is not fastened, an audi-
ble warning signal sounds for 6 seconds.
Page 119 of 205
118DRIVING TIPS
Driving economically while protecting the environmentVarious factors determine fuel consump-
tion, the impact on the environment and
wear-and-tear of the engine, brakes and
tyres.
Your personal style of driving
determines to a great extent the economi-
cal aspect and the development of exhaust
and noise:
Do not warm up engine when the vehicle is stationary.
At idling speed it takes a very long time until
the engine becomes operationally warm.
However, in the warm-up phase, wear and
the discharge of pollutants is particularly
high. For this reason, drive off immediately
the engine has started and avoid high en-
gine speeds.
The cold engine consumes approx. 15 - 20
litres/100 km of fuel immediately after start-
ing. Fuel consumption drops to 10 litres/100
km after just 1 kilometre. The engine
reaches its operating temperature (outside
temperature and engine dependent) only
after about 4 to 10 kilometres and the fuel
consumption then stabilizes. You should
therefore avoid driving short distances
whenever possible.
Avoid full throttle acceleration.
Accelerating with feeling not only consid-
erably improves fuel economy but also re-
duces the impact on the environment and
wear-and-tear.
Do not drive at unnecessarily highengine revs - change up as soon as
possible and only change down when the engine no longer runs smoothly.
Fuel consumption, for example, is more
than twice as high in 2nd gear than it is in
top gear. At the same time, the lower en-
gine speed means a reduction in engine
noise.
Try not to drive at maximum speed.
Fuel consumption, exhaust pollution and
noise increase disproportionately at high
speeds. If you make use of approximately
only 3-quarters of top speed, your fuel con-
sumption will be reduced by about half.
Experience has shown that the loss in time
is only marginal.
Drive as smoothly as possible andlook well ahead.
Unnecessary acceleration and braking has
to be paid for with higher fuel consumption
and a greater impact on the environment.
Switch off the engine when stand-
ing in traffic (traffic lights, railway
crosses etc.).
Individual operating conditions
naturally also affect fuel consumption.
The following factors, for instance, are not
favourable to good fuel consumption:
High traffic density, particularly in large
towns with numerous traffic lights.
Frequent stop/start driving, always re-
starting and warming up the engine.
Driving in heavy, slow moving traffic in
low gear so that the engine speed is rela-
tively high in relation to the speed driven.
Obviously, fuel consumption is also affected
by factors over which the driver has no con-
trol. It is, for example, normal for fuel con-
sumption to increase in the winter or in
severe conditions such as poor roads, tow-
ing a trailer etc.
Page 138 of 205
137
GENERAL MAINTENANCE
Warning
Particular care is required when per-
forming work in the engine compart-
ment!
Never open the bonnet if you see
that steam or coolant is escaping
from the engine compartment - risk
of scalding!
You must wait long enough, until the
steam or coolant has stopped escap-
ing.
Switch off engine and withdraw ig-
nition key.
Apply handbrake properly.
Move gearshift into Neutral (on
models with automatic gearbox mo-
ve selector lever into position „P“).
Allow engine to cool down.
If the engine is still warm:
- do not place your hand into the ra- diator fan, it might start suddenly.
- do not open filler cap of coolant reservoir as cooling system is
pressurized - risk of scalding.
Avoid short circuits in the electri-
cal system - particularly at the bat-
tery!
If you wish to work under the ve-
hicle, you must secure the vehicle
from rolling away and support it with
suitable supporting blocks: the car
jack is not sufficient for this - risk of
injury!
If it is necessary to carry out test
work when engine is running, there
is an additional risk from rotating
parts - e.g. ribbed belt, alternator,
radiator fan etc. - and from the high-
voltage ignition system.
Never touch the electrical cables
of the ignition system.
Absolutely avoid any jewellery,
loose items of clothing or long hair
from getting into the rotating parts of
the engine - Hazard! Therefore re-
move any jewellery beforehand, tie
up your hair and wear tight fitting
clothing.
It is essential to comply with all the
warning information given in this
manual and with the general rules of
safety when carrying out work on the
engine.
When topping up fluids, ensure that no mix-
ups occur otherwise this may cause severe
operating problems!
The floor below the car should be
inspected regularly in order to de-
tect leaks in good time. If patches of oil or other fluids are visible, the car shouldbe taken to a Škoda Dealer for an inspec-
tion.
Page 164 of 205
163
DO-IT-YOURSELF
Changing a wheelWarning
In the case of a flat tyre or punc-
ture, park the vehicle off the road,
switch on the hazard warning lights
and place the warning triangle in po-
sition - note any statutory require-
ments.
All the vehicle occupants should
leave the car and move to a safe area
(e.g. behind safety barrier).
Apply handbrake firmly and engage
a gear. Chock the opposite wheel with
a stone or similar if the car is stand-
ing on a slope.
Never start the engine when the
car is jacked up - risk of accident!
If towing a trailer, unhitch the
trailer from the car before changing
the wheel.
Carry out wheel change on a flat, level
surface, as far as possible.
Remove the car tool kit and spare wheel
from the luggage compartment.
Attach the wire hook (from the car tool
kit) at the edge of the full wheel trim* oppo-
site the air valve. Push the wheel wrench
through the wire hook and pull off the wheel
trim - see illustration.
If light-alloy wheels are fitted, use the
plastic clip supplied to pull off the covers
for the wheel bolts.
Unscrew the safety wheel bolts* - see
page 166.
Fit wheel wrench onto the wheel bolt as
far as the stop and turn to the left. Hold the
wrench as close as possible to its end for
this operation. If the bolts cannot be slack-
ened, you can carefully apply pressure to
the end of the wheel wrench with your foot.
Ensure that you are standing properly and
hold tight on the car. Slacken the wheel
bolts about one turn.