SKODA OCTAVIA TOUR 2010 1.G / (1U) Columbus Navigation System Manual

Seats and Storage
70
The roof rack*DescriptionPay attention to the following points if you wish to transport luggage or other items on
the roof of your vehicle:
A special roof luggage rack system was de veloped for the vehicle, that is why you
should only use a roof luggage rack which has been released for use by Škoda Auto.

The base carrier is the basis for a comple te roof luggage rack system. Separate
additional holders are required for safety reasons for transporting luggage, bikes, surf-
boards, skis and boats.

The basic version of the roof luggage ra ck system and further components are
obtainable as accessories from the specialist garages.Caution

If you use other roof rack systems or if th e roof bars are not properly fitted, then
any damage which may result to your car is not covered by the warranty agreements.
It is therefore essential to pay attention to the fitting instructions supplied with the roof
luggage rack system.

On models fitted with a power sliding/tilting roof, ensure that the opened
sliding/tilting roof does not strike any items of luggage transported on the roof.

Ensure that the opened boot lid does not collide with the roof load.For the sake of the environment
The increased aerodynamic drag results in a higher fuel consumption. One should
therefore take off the roof bar system after use.
Note
A roof rail is obtainable from a specialist garage if hasn't been fitted onto an estate car
at the works, which carries out the professional fitting.
Lashing points (Octavia)Installing– The plastic caps fig. 80 can be removed by inserting a thin screwdriver into the
recess of the caps and carefully leve r out the caps to avoid paint damage.
– The feet are inserted into the openings of the roof bars.
Note

Pay attention to the information regarding assembly and disassembly in the
attached instructions.

If you have any questions, plea se contact a specialist garage.

The figure is not valid for an estate car.
Roof loadDistribute weight evenly over the roof lu ggage rack system. The maximum permissible
roof load (including roof rack system) of 75 kg and the maximum permissible total
weight of the vehicle should not be exceeded.
You cannot make full use of th e permissible roof load if you use a roof luggage rack
system with a lower load carr ying capacity. The load transported on the roof luggage
rack system must not exceed the weight limit which is stated in the fitting instructions.
Fig. 80 Attachment points for
base roof carrier
s2rc.book Page 70 Thursday, April 22, 2010 10:58 AM

Seats and Storage71
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING

The items which you transport on the roof bar system must be reliably
attached - risk of accident!

You must on no account exceed the pe rmissible roof load, the permissible
axle loads and the permissible gross weight of your vehicle - risk of accident!

Please note that the handling properties of your vehicle change when you
transport heavy or bulky items on the roof bar system as a result of the
displacement of the centre of gravity an d the increased wind attack area - risk
of accident! You must absolutely adapt your style of driving and the speed of
the vehicle to the sp ecific circumstances.
Cup holder in front centre consoleAfter pressing in direction of arrow, the cup holder slides out and opens up fig. 81 .
It is designed to place drink cans or othe r beverage packagings in (with a content of
0.33°ltr. or 0.5°ltr.).
WARNING

Do not place any hot beverages into th e cup holder. If the vehicle moves,
they may spill - risk of scalding!

Do not use any cups or beakers which are made of brittle material (e.g.
glass, porcelain). You might be injured by them in the event of an accident.
Caution
Do not open the beverages in the cup holder while driving. They may spill when
braking and while doing so damage the vehicle.Note holderThe note holder is designed e.g. for attaching a car park ticket in parking areas.
The attached note has to always be removed before starting off in order not to restrict
the driver's vision.
Fig. 81 Front centre console:
Cup holder
Fig. 82 Windscreen: Note
holder
s2rc.book Page 71 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage
72
Ashtray*Front ashtrayOpening ashtray– Press on the bottom part of the cover of the ashtray at the point of the arrow
fig. 83 .Removing ashtray insert– Remove the ashtray insert in direction of arrow .Insert ashtray insert– Insert the ashtray insert and press it slightly in direction of arrow .
WARNING
Never lay flammable objects in the ashtray basin - risk of fire!Rear ashtrayRemoving ashtray– Fold the cover backwards and remove the ashtray in direction of arrow.Replacing ashtray– Press the ashtray vertically downwards and fold the cover down.
There is a can holder attached to the inner side of the ashtray cover.
WARNING
Never lay flammable objects in the ashtray basin - risk of fire!
Fig. 83 Centre console: Front
ashtrayFig. 84 Remove ashtray and
replace
AA
AB
Fig. 85 Low centre console: Rear
ashtray
s2rc.book Page 72 Thursday, April 22, 2010 10:58 AM

Seats and Storage73
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Cigarette lighter*, power socketsCigarette lighter
You can also use the socket on the ci garette lighter for other electrical
appliances.Using the cigarette lighter– Press in the button of the cigarette lighter fig. 86 .
– Wait until the button jumps forward.
– Remove the cigarette lighter immediately and use it.
– Insert the cigarette lighter again into the socket.Using the socket– Take out the cigarette lighter.
– Insert the plug of the electrical appliance into the socket of the cigarette lighter.
The 12 volt power socket can also be used to supply power to additional electrical
accessories with a power uptake up to 120 watts.
WARNING

Take care when using the cigarette lighter! Not paying proper attention or
incorrect use the cigarette lighter in an uncontrolled manner may result in
burns.

The cigarette lighter and the power sock et also operates when the ignition
is switched off or the ignition key withdrawn. You should therefore never leave
children unattended in the vehicle.Caution
Always use matching plugs to av oid damaging the power socket.
Note

Connecting electrical components when the engine is not running will drain
the battery of the vehicle - risk of battery draining!

Further information page 166, “Accessories, changes and replacement of
parts”.
Power socket in the luggage compartment (Combi)The socket is located on the left in the luggage compartment.
– Open the cover of the power socket fig. 87 .
– Connect the plug of the electrical appliance to the socket.
Fig. 86 Centre console: Ciga-
rette lighter
Fig. 87 Luggage compartment:
Power socket
s2rc.book Page 73 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage
74
The power socket, which fulfils the requirem ents of DIN standard ISO 4165, must only
be used for connecting approv ed electrical accessories with a power uptake of up to
120 watts. The vehicle battery will be discharged in the process if the engine is
stationary.
The same remarks apply here as for page 73.
Further information page 166, “Accessories, change s and replacement of parts”.Storage compartmentsOverviewYou will find the following storage facilities in your vehicle:
WARNING

Please do not place anything on top of the dash panel. Such objects might
slide or fall down when driving (when accelerating or cornering) and may
distract you from concentrating on the traffic situation - risk of accident!

Use the storage compartments in the door panels only for small items which
do not project out of the compartment in order to avoid any interference with
the proper operation of the side airbags.

Ensure that when driving no objects from the centre console of from other
storage possibilities may get into the fo otwell of the driver. You would then no
longer be able to apply the brakes, oper ate the clutch or accelerator - risk of
accident!
Storage compartment on the front passenger sideOpening and closing the storage compartment on the front passenger
side– Pull the handle of the lid in direction of arrow fig. 88 and fold it downwards.
– Raise the lid and press it until the catch is heard to engage.
The storage compartment can be locked an d unlocked using the vehicle key (if the
storage compartment is lockable*).
WARNING
The storage compartment must always be closed when driving for safety
reasons.
Storage compartment on the front passenger side
 page 74
Storage compartment below steering wheel
 page 9
Storage compartment in the middle part of the dash
panel
page 9
Storage compartment for spectacles*
page 75
Storage compartment in the front doors
 page 9
Front seat armrest with storage compartment*
page 75
Rear armrest with storage compartment*
page 76
Clothes hooks*
page 76
WARNING (continued)
Fig. 88 Dash panel: Storage
compartment on the front
passenger side
s2rc.book Page 74 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage75
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Storage compartment for spectacles*Opening and closing the storage compartment for spectacles– Press on the cover of the storage compartment at the point of the arrow, the
compartment opens or closes fig. 89 .Removing– Open the storage compartment in the vertical position and take it out by pulling on
the hinge.Installing– Installation takes place in the reverse order.
WARNING
The compartment must only be opened when removing or inserting objects
and otherwise must be kept closed.
Note
Do not insert particularly large spectacles.
Front seat armrest with storage compartment*The armrest is adjustable in height.Opening storage compartment– Press button fig. 90 .
– Open the lid of the armrest in the direction of arrow.Closing storage compartment– Fold down the cover of the armrest.Setting height– Press the button in direction of arrow.
– Fold the armrest downwards or upwards and release the button.
Note
The moving space of the arms can be restrict ed if the armrest is folded down. In city
traffic the armrest should not be folded down.
Fig. 89 Centre console: Storage
compartment for spectacles
Fig. 90 Armrest: Storage
compartment
ABAA
s2rc.book Page 75 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage
76
Rear seat armrest with storage compartment*– The armrest can be folded forwards in di rection of arrow with the aid of the belt
 fig. 91 .
– The armrest includes a storage compartment. Press the button in direction of arrow and open the storage compartment in direction of arrow .
Clothes hooks*A clothes hook is located above the rear doors fig. 93 .
WARNING

Ensure that any clothes hanging from the hooks do not impair your vision to
the rear.

Use the hooks for hanging only light item s of clothing and ensure that there
are no heavy or sharp-edged objects in the pockets.
Fig. 91 Rear seats: ArmrestFig. 92 Rear seats: Fold the
armrest forwards
A1
A2
Fig. 93 Rear door: Clothes hooks
s2rc.book Page 76 Thursday, April 22, 2010 10:58 AM

Heating and air conditioning system77
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Heating and air conditioning systemAir outlet ventsFig. 94 Air outlet ventsOpen air outlet vents– Turn the vertical thumbwheel (not when in the end position).Close air outlet vents– Turn the vertical wheel into the end position.Redirecting air flow– Swivel upward or downward the grille of the vents in order to change the direction
of the air flow using the vert ically arranged thumbwheel.
– Turn the horizontal thumbwheel on the vent to the right or left in order to change
the air flow to the appropriate side.
You can set the air supply to the individu al air outlet vents using the control
 fig. 95 . Air outlet vents 3 and 4  fig. 94 can also be opened or closed individually.
Unwarmed or cooled air will flow out of the opened air outlet vents according to the
setting of the control dial fig. 95 and according to outer atmospheric
conditions.
HeatingUsing the system
The heating system delivers air into the interior of the vehicle and
warms it as required.Setting temperature– Turn the control dial fig. 95 to the right in order to increase the temperature.
– Turn the control dial to the left in order to increase the temperature.Controlling blower– Turn the blower switch into one of the po sitions, 1 to 4, in order to switch the
blower on.
– Turn the blower switch into position 0 in order to switch the blower off.
– If you wish to shut off the fresh air su pply, use the button - recirculated air
mode .Control for air distribution– You can adjust the direction of the air flow using the air distribution control
 page 77.
AC
AA
Fig. 95 Heating: Control
elements
AAAAABAB
AD
AC
s2rc.book Page 77 Thursd ay, April 22, 2010 10:58 AM

Heating and air conditioning system
78
The air inlet in front of the windscreen must be free of ice, snow or leaves in order to
ensure that the heating and ventilation systems operate properly.
The heating effect is dependent upon the c oolant temperature, thus full heat output
only occurs when the engine has reached its operating temperature.
The blower should aways be on to prevent the windows from misting up.
WARNING
You should not leave recirculated air mode on over a longer period of time, as
“stale” air may result in fatigue in the driver and occupants, divert your atten-
tion and also cause the windows to mist up. The risk of having an accident increases. Switch recirculated air mo
de off as soon as the windows begin
misting up.
Note

The whole heat output will be needed to unfrost the windscreen and side
windows. No warm air will be fed to the footwell. This can lead to restriction of the
heating comfort.

The used air streams out through the air removal openings in the luggage compart-
ment.

The button cannot be pressed if the control dial is in the position
 or close
to this position.
Set heatingRecommended settings of heating controls for:
WARNING (continued)
AD
AC
Setup
Setting of the control dial
Button
Air outlet vents 3
Air outlet vents 4
Defrosting the windscreen and
side windows
To the right up to
the stop
3

Switched off
Closing
Open and align with the side window
Free windscreen and side win-
dows from mist
In heating area
2 or 3

Switched off
Closing
Open and align with the side
window
The fastest heating
To the right up to the stop
3

Switched off
Opening
Opening
Comfortable heating
Desired tempera- ture
2 or 3
 or 
Switched off
Closing
Opening
Fresh air mode - ventilation
To the left up to the
stop
Desired position

Switched off
Opening
Opening
AA
AB
AC
AD
s2rc.book Page 78 Thursd ay, April 22, 2010 10:58 AM

Heating and air conditioning system79
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Recirculated air mode
In recirculated air mode air is sucked out of the interior of the vehicle
and then fed back into the interior.Recirculated air mode prevents polluted air outside the vehicle from getting into the
vehicle, for example when driving through a tunnel or when standi ng in a traffic jam.Switching recirculated air mode on– Press the button - the warning light lights up in the button page 77, fig. 95 .Switching recirculated air mode off– Press again the button - the warning light in the button goes out.
The button cannot be pressed if the control dial is in the position
 or close
to this position.
WARNING
You should not leave recirculated air mode on over a longer period of time, as
“stale” air may result in fatigue in the driver and occupants, divert your atten-
tion and also cause the windows to mist up. The risk of having an accident
increases. Switch recirculated air mode off as soon as the windows begin
misting up.Air conditioning system*Description
The air conditioning system is a combined cooling and heating system.
It makes it possible to optimally control the air temperature at any
season of the year.Description of the air conditioning system
It is important for your safety and for your driving comfort that the air conditioning
system is operating properly. The air conditioning only operates if button
page 80, fig. 96 is pressed and
the following conditions are met:

engine running,

outside temperature above +5 °C and

blower switch switched on (positions 1 to 4).
If the cooling system is switched on, the temperature and air humidity drops in the
vehicle. The wellbeing of the occupants of the car is enhanced as a result of this partic-
ularly at high outside temperatures and a high air humidity. The system prevents the
windows misting up during the cold season of the year.
The heating effect is dependent upon the c oolant temperature, thus full heat output
only occurs when the engine has reached its operating temperature.
It is possible to briefly activate recirculat ed air mode in order to enhance the cooling
effect  .
Air at a temperature of about 5°C may flow out of the vents under certain circum-
stances when the cooling system is operating. Lengthy and uneven distribution of the
air flow out of the vents (in particular at the leg area) and large differences in temper-
ature, for example when getting out of the ve hicle, can result in chills in sensitive
persons.
The air inlet in front of the windscreen must be free of ice, snow or leaves in order to
ensure that the heating and cooling systems operate properly.
After switching on the cooling Condensation from the evaporator of the air condi-
tioning may drip down and form a puddle be low the vehicle. This is quite normal and
not an indication of a leak!
WARNING

For your own safety and that of other road users, ensure that all the
windows are free of ice, snow and misting. Please familiarize yourself about
how to correctly operate the heating and ventilation systems, how to demist
and defrost the windows, as well as with the cooling mode.

You should not leave recirculated air mode on over a longer period of time,
as “stale” air may result in fatigue in the driver and occupants, divert your
attention and also cause the windows to mist up. The risk of having an accident



AC
AC
AD
s2rc.book Page 79 Thursd ay, April 22, 2010 10:58 AM