ECU SKODA SUPERB 2005 1.G / (B5/3U) Owner's Guide

Towing a trailer201
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Distribution of the load
Distribute the load in the trailer in such a way that any heavy items are
located as close as possible to the axle. Secure the items to prevent them
slipping.
Tyre pressure
Select the tyre inflation pressure on your vehicle for that of “fully laden”,
⇒
page 236. The inflation pressure of the tyres fitted to the trailer adjust
in accordance with the manufacturer's recommendation.
Exterior mirrors
You have to have additional exterior mirrors fitted if you are not able to see
the traffic behind the trailer with the standard rear-view mirrors. Both exte-
rior mirrors should be attached to folding arms. Adjust the mirrors so that
they provide you with an adequate field of view to the rear.
Headlights
Before starting off with a hitched trailer, also check the setting of the head-
lights. Alter the setting as necessary with the aid of the headlight beam
adjuster ⇒page 59.
Detachable ball head
The ball rod is detachable on vehicles which feature a factory-fitted towing
device. It is stowed together with separate fitting instructions in the spare
wheel well in the luggage compartment of the vehicle.
Further information on the towing device ⇒page 202.
Note
•We recommend that you also have your vehicle inspected between
service intervals if you tow a trailer frequently.
•The handbrake on the towing vehicle must be put on when coupling
and decoupling the trailer.
Driving Tips
Particular caution is required when towing a trailer.
– Do not, as far as possible, drive with your vehicle unladen and the trailer laden.
– Do not make full use of the legal maximum speeds. This applies in particular to downhill sections.
– Apply the brakes in good time.
– Keep a check on the coolant temperature gauge if the outside temperature is high.
Distribution of weight
The distribution of the weight is very poor if your vehicle is unladen and
the trailer is laden. Maintain a particularly low speed if you cannot avoid
driving with this combination.
Driving speed
Do not drive faster than 80 km/hour for safety reasons. This also applies
for countries in which higher speeds are allowed.
The fact that the driving stability of the vehicle + trailer combination
reduces with increasing speed means that the legally allowed speed
should not be used when there are unfavourable road, weather or wind
conditions, particularly near accident black spots.
You must always reduce your speed immediately as soon as you detect
even just the slightest swaying of the trailer. On no account attempt to
stop the trailer from “swaying” by accelerating.
Apply the brakes in good time! If the trailer is fitted with a trailer brake,
apply the brakes gently at first and then brake firmly. This will avoid brake
jolts resulting from the trailer wheels locking. Shift down gears in good
s3ec.book Seite 201 Montag, 2. Mai 2005 3:42 15

Fuel
216
below 0°C can result in operational problems because the diesel becomes
viscous as a result of paraffin separation.
It is therefore the case that DIN EN 590 prescribes diesel fuel class for
certain periods of the year which can also be purchased at the corre-
sponding time during the year. “Winter-grade diesel fuel” will still operate
properly even at a temperature of -20°C.
It is often the case in countries with different climatic conditions that diesel
fuels available have a different temperature characteristic. Škoda dealers
and filling stations in the country concerned will be able to provide you with
information regarding the diesel fuels available.
Prewarming fuel
The vehicle is fitted with a fuel filter prewarming system. This secures
operation of a vehicle using diesel fuel down to an environmental temper-
ature of -25°C.
Biofuel
We recommend refuelling with diesel fuel at temperatures below -10°C.
Caution
It is not permitted to add the various fuel additives on the market, including
petrol, to diesel fuel in order to improve its flow properties.
Refuelling
Refuelling procedure
Opening the fuel filler cap
– Unlock the fuel filler flap with the switch in the driver door
⇒page 31.
– Open the fuel filler flap fully.
– Unscrew the cap by turning it to the left.
– Place the cap onto the top of the fuel filler flap ⇒fig. 166 .
Closing fuel filler cap
– Screw on the cap by turning it to the right until it is heard to lock.
Fig. 166 Filler flap with
cap unscrewed
s3ec.book Seite 216 Montag, 2. Mai 2005 3:42 15

Inspecting and Replenishing
220
•If you wish to work under the vehicle, you must secure the
vehicle from rolling away and support it with suitable supporting
blocks: the car jack is not sufficient for this - risk of injury!
•In cases where it be necessary to carry out inspection work
when the engine is running there is an additional risk from rotating
parts (e.g. the V-ribbed belt, alternator, radiator fan) and from the
high-voltage ignition system. Pl ease observe in addition the
following:
−Never touch the electrical cables of the ignition system.
− Absolutely avoid any jewellery, loose items of clothing or
long hair from getting into the rotating parts of the engine -
Hazard! Therefore remove any jewellery beforehand, tie up your
hair and wear tight fitting clothing.
•Please also comply with the warning instructions stated below
when carrying out any essential work on the fuel system or on the
electrical system:
−Always separate the car battery from the electrical system.
− Do not smoke.
− Never carry out any work close to naked flames.
− Always keep a working fire extinguisher at hand.
Caution
When replenishing fluids in the engine, always ensure that the fluids are
on no account mixed up. This may result in major operating problems and
also vehicle damage!
Overview of the engine compartment
The main inspection points
Fig. 170 6-cylinder 2.8 ltr./ 142 kW petrol engine
Battery (below a cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake fluid reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coolant expansion bottle . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil filler opening . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield washer fluid reservoir . . . . . . . . . . . . . . . . . . . .
Power steering reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING (continued)
A1228
A2222
A3227
A4225
A5223
A6233
A7191
s3ec.book Seite 220 Montag, 2. Mai 2005 3:42 15

Breakdown assistance
248
•Do not drive with this spare wheel at more than 80 km/h - risk of acci-
dent. Avoid accelerating at full throttle, sharp braking and fast cornering.
•The inflation pressure for this spare wheel is identical to the inflation
pressure of the standard tyres.
•Use this spare wheel only to reach the nearest service station as it is
not intended for continuous use.
Changing a wheel
Preliminary work
The following steps should be carried out before actually
changing the wheel.
– If it is necessary to change a wheel, park the vehicle as far away as possible from the traffic flow. The place you choose
should be level.
– Have all the occupants get out. While changing a wheel, the
occupants of the vehicle should not stand on the road (it is
better behind a crash barrier).
– Apply the handbrake firmly.
– Engage 1st gear or if your vehicle is fitted with an automatic
gearbox, position the selector lever into position P .
– If a trailer is coupled, uncouple it.
– Take the vehicle tool kit and the spare wheel ⇒ page 247
out of the luggage compartment.
WARNING
•If you find yourself in flowing traffic switch on the hazard
warning lights system and place the warning triangle on the side of
the road at the prescribed distance from your vehicle while
observing all national legal provisions. In this way you are
protecting not only yourself but also other road users.
•Never start the engine with the vehicle sitting on the raised jack
- danger of suffering injury!
Caution
If you have to change a wheel on a slope first block the opposite wheel
with a stone or similar object in order to secure the vehicle from unexpect-
edly rolling away.
Note
Comply with the national legal regulations.
Changing a wheel
Always change a wheel on a level surface as far as possible.
– Take off the full wheel trim* ⇒page 249 or the caps
⇒ page 251.
– In the case of light alloy wheels remove the wheel trim cap ⇒page 250.
– Slacken the wheel bolts ⇒page 251.
s3ec.book Seite 248 Montag, 2. Mai 2005 3:42 15

Breakdown assistance
250
Installing
– First press the full wheel trim onto the wheel at the valve opening provided. Then press the full wheel trim into the
wheel in such a way that its entire circumference locks
correctly in place.
Caution
•Use the pressure of your hand, do not knock on the full wheel trim!
Heavy knocks mainly on the points where the full wheel trim has not been
inserted into the wheel, can result in damage to the guide and centering
elements of the full wheel trim.
•First check for yourself that the theft-deterrent wheel bolt is located
⇒ page 254, “Securing wheels against being stolen” in the hole in the
area of the valve before fitting the full wheel trim onto a steel wheel which
is attached with a theft-deterrent wheel bolt.
Wheel trim caps*
Removing
– Carefully ⇒fig. 188 lever off the wheel trim cap using the
removal hook .
Fig. 188 Changing a
wheel: Pulling off the
wheel trim cap
s3ec.book Seite 250 Montag, 2. Mai 2005 3:42 15

Breakdown assistance
254
– Screw in the wheel bolts and tighten them slightly with the aid
of the hexagon socket.
– Unscrew the assembly pin and screw in the remaining wheel bolt also slightly.
The wheel bolts must be clean and must turn easily.
The hexagon socket in the handle of the screwdriver makes it simpler to
fit on the wheel bolts. The reversible blade should be pulled out for this
step.
When fitting on unidirectional tyres, ensure that the tyres rotate in the
correct direction ⇒page 241.
Note
Do not use the hexagon socket in the handle of the screwdriver for slack-
ening or tightening the wheel bolts.
Securing wheels against being stolen
You need a special adapter for slackening the safety
wheel bolts.
– Pull off the full wheel trim/cap from the wheel hub or cap from
the safety wheel bolt.
– Insert the adapter with its toothed side fully into the inner toothing of the safety wheel bolt right down in such a way
that only the outer hexagon is jutting out ⇒ fig. 194.
– Insert the wheel wrench fully onto the adapter .
– Slacken the wheel bolt, or tighten it firmly ⇒page 240.
– Reinstall the full wheel trim/wheel cap after removing the adapter or place the cap onto the safety wheel bolt.
Fig. 194 Safety wheel
bolt with adapter
AB
AA
AB
s3ec.book Seite 254 Montag, 2. Mai 2005 3:42 15

Fuses and light bulbs267
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Lighting in storage compartment on front passenger
side
– Insert a small screwdriver into the slot next to the light
⇒fig. 205 and carefully lever out the light in the direction of
the arrow .
– Unplug the connector.
– Take the faulty bulb out of and insert a new one.
– Plug in plug.
– Insert the light and press it into the wall of the storage compartment.
Entry lighting
– Insert a small screwdriver into the slot next to the light ⇒fig. 206 and carefully lever out the light.
– Unplug plug .
– Push away the spring clip on the cover and remove the cover.
– Take the faulty bulb out of and insert a new one.
– Insert the cover again and secure it by locking it in place.
– Plug in plug.
– Insert the light from the rear and press it forwards up to the stop.
Fig. 205 Storage
compartment: Lighting
A1
Fig. 206 Inner part of
the door: Entry light
A1
A2
s3ec.book Seite 267 Montag, 2. Mai 2005 3:42 15

Index275
Operation in winter
Biodiesel . . . . . . . . . . . . . . . . . . . . . . . . 215
De-icing windows . . . . . . . . . . . . . . . . . . 208
Snow chains . . . . . . . . . . . . . . . . . . . . . . 241
The battery . . . . . . . . . . . . . . . . . . . . . . . 231
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Overview of the engine compartment . . . . . 220
P
Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Paint damage . . . . . . . . . . . . . . . . . . . . . . . 208
Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Parking aid . . . . . . . . . . . . . . . . . . . . . . . . . 127
Parking light . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Parking lights . . . . . . . . . . . . . . . . . . . . . . . . . 57
Passive Safety . . . . . . . . . . . . . . . . . . . . . . . 149
Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Petrol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Petrol engines Starting engine . . . . . . . . . . . . . . . . . . . . 124
Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Polishing . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Power socket . . . . . . . . . . . . . . . . . . . . 100, 101
Power steering . . . . . . . . . . . . . . . . . . . . . . 191
Power windows Central locking system . . . . . . . . . . . . . . . 52
Operational problems . . . . . . . . . . . . . . . . 53
Switch on the driver's door . . . . . . . . . . . . 50
Switches in front passenger door and in rear doors . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
R
Raise vehicle . . . . . . . . . . . . . . . . . . . . . . . . 252
Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Rear fog light . . . . . . . . . . . . . . . . . . . . . . . . . 58
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Rear window
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Rear window heater . . . . . . . . . . . . . . . . . . . . 64
Rear-view mirror Exterior mirrors . . . . . . . . . . . . . . . . . . . . . 70
Interior rear-view mirror . . . . . . . . . . . . . . 68
Recirculated air mode Heating and ventilation . . . . . . . . . . . . . . 112
Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Emergency release of fuel filler flap . . . . 217
Remote control . . . . . . . . . . . . . . . . . . . . . . . 47 Synchronisation . . . . . . . . . . . . . . . . . . . . 48
Replacing fuses . . . . . . . . . . . . . . . . . . . . . . 260
Replacing windscreen wiper blades . . . . . . . 68
Roof aerial . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Running in the car . . . . . . . . . . . . . . . . . . . . 192
S
Safe distance to steering wheel . . . . . . . . . . 121
Safe securing . . . . . . . . . . . . . . . . . . . . . . . . . 43
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Safety instructions Engine compartment . . . . . . . . . . . . . . . 219 Safety wheel bolts . . . . . . . . . . . . . . . . . . . . 254
Saving electrical energy . . . . . . . . . . . . . . . . 194
Seat belt
Warning light . . . . . . . . . . . . . . . . . . . . . . . 38
Seat belt height adjuster . . . . . . . . . . . . . . . 159
Seat belt warning light . . . . . . . . . . . . . . . . . 158
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Belt tensioners . . . . . . . . . . . . . . . . . . . . 160
blocking . . . . . . . . . . . . . . . . . . . . . . . . . 160
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 213
fasten . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Height adjustment . . . . . . . . . . . . . . . . . . 159
Safety instructions . . . . . . . . . . . . . . . . . 157
taking off . . . . . . . . . . . . . . . . . . . . . . . . . 159
Warning light . . . . . . . . . . . . . . . . . . . . . . . 38
Seat heaters . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Selector lever . . . . . . . . . . . . . . . . . . . . . . . . 132
Selector lever positions . . . . . . . . . . . . . . . . 132
Service Interval Display . . . . . . . . . . . . . . . . . 16
Service intervals . . . . . . . . . . . . . . . . . . . . . . . 16
Service key . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Setting temperature The air conditioning system . . . . . . . . . . 110
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . 15
Shifting of gears . . . . . . . . . . . . . . . . . . . . . . 125
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . 167
Ski bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . . 241
s3ec.book Seite 275 Montag, 2. Mai 2005 3:42 15