window SKODA SUPERB 2009 2.G / (B6/3T) Amundsen Navigation System Manual

General information
8 ated by touching the screen. Active
fields, which call up a function or a
menu, are called “
function buttons
” / .
The following information is displayed in the main menu: the selected radio station (i
ts frequency or
designation);
selected waveband; activation for the rece
ption of traffic reports;
current menu. “Pop-up window” If you press the function key on the sc
reen, a so-called “pop-up window” will
open where all possible se
t-up options are displayed.
Briefly press the desired set-up option. Th
e pop-up window will disappear and the
newly selected set-up option is
displayed in the function key.
“Check box” Some functions can only
be switched on or off.
There is a so-called “check box” in front of a function which can only be switched on or off. A tick in the check box
7 indicates that the functi
on is switched on, an
empty check box
8, indicates that it
is switched off.
Briefly press the corresponding function key for switching on or off.
Input mask for free text inputIn some of the menus you can enter a free text, for example, when entering a new destination or while se
arching for the name of a point of
interest. – Press to accept a character se
quence offered by the system or
press in order to delete the characters in the entry line.
– When in the entry window, press on a character shown on the keypad
block to accept it into the entry line.
– You can also delete or change the character sequence in the entry line
as well as insert additional characters.
Further input possibilities: - changes from upper case to lower case and vice versa. - opens the input mask for digits an
d special characters. The function key
changes to . Press , to change again to the letter input mask.˜ - space key for entering spaces. or - moves the character entry cursor (the cursor) in the entry line to the left or right.
- opens a pop-up window with special characters.
AD
AF
AAABACAE
AF
BAT-20H1085
Fig. 3 Input mask for free text input
OKDelete
45
A-Z
A-Z
‚
b
ÄÜ
s36c.b.book Page 8 Thursday, April 9, 2009 2:50 PM

General information
9
- deletes characters in the entry line
starting from the position of the char-
acter entry cursor from right to left. Selecting letters based on specific characters Some letters in the input masks are al
so marked with a small triangle “
a”. This indi-
cates that specific characters base
d on this letter can be selected.
Continue to press down on
the corresponding function key with your finger until a
pop-up window with these specific characte
rs can be displayed. Press to accept the
desired character into the entry line - the po
p-up window will close. If no entries are
entered, the pop-up window will cl
ose automatically after a few seconds.
Input mask for selecting the destination addressWhen entering the destination address,
it is only possible to enter the
characters in the sequence which corresponds to the destinations stored in the navigation system. Limiting the destination an
d selecting from the list
– You can open a list of the selectable destinations any time by pressing
the function key while making
entries in the entry line. Only
destinations selectable from the navigation memory which corre-spond to the requirements and the
character sequence in the entry
line will be displayed.
– The number of selectable destinatio
ns will be displayed in the entry
line if fewer than 99 dest
inations can be selected.
–If fewer than six destinations ar
e selectable, the entry window will
close automatically and a list of possible destinations will be displayed.
Delete
BAT-20H1086
Fig. 4 Input mask for selecting the destination address
List/OK
s36c.b.book Page 9 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
10
Range selector key SETUPTo n e s e t t i n g sBy press ing the button and pres si ng on the functi on key in the
RADIO

mode, you can select the following para
meters using the menu control button :
•
- , ,
and - Volume when switching
on, volume of incoming traffic announce
ments, volume of navigation announce-
ments and speed dependent volume adjustment;•
- Treble setting;
•
- Midtone setting;
•
- Bass setting;
•
- Setting of the volume ratio between the left and right side;
•
- Setting of the volume ratio between the front and the rear;
•
* - Setting the equalizer (linear,
language, rock, cl
assical, dance);
•
* - setting of the surround tone.
GALA function Your radio increases automatically its volu
me with the increasing vehicle speed. A
higher setting value results in a stronger volume increase.
Note
You can set the tone parameters using th
e menu control button or the function
keys or .System settingsPress the button and select the function key .You can select between the following parameters:•
- Menu language for the displa
ys and the language messages;
•
- Keypad display for text entry;
•
* - if your vehicle
is equipped with clim
atronic, the setting
change is displayed when it is activated;•
- Setting the brightness of the screen;
•
- Factory settings;
•
- the information regarding the complete memory capacity of
the SD card and the size of the memory assi
gned to the navigation data is displayed
on the screen;•
- Removing the SD card.
Radio set-upsPress the button in the
RADIO
mode.
Switching the traffic announcements on or off – If you wish to switch the reception of traffic reports on or off, press the
function key .
Determining the station selection via the – By pressing on or , you can select the source
from which the stations are to be selected while in the
RADIO
mode
using the arrow keys. If the is selected, only stored stations from the memory list are called up. The symbol “
ƒ @ „” is
displayed on the screen.
Switching the RDS function on or off (RDS regional) – Press on the function key (regional station) and select a
set-up in the opening pop-up window.
SETUP
To n e
A10
Vo lume
Maximum switch on volume
Traffic announcements (TP)
Navigation volume
Speed dependent vol Adjustment
Tre b l eMidtoneBassBalanceFa d e rEQ SettingsSurround
A10
+
-
SETUP
System
Language
Keypad displayA/C display timeScreenFactory settingsSD card statusRemove SD card
SETUPTraffic information (TP)
Arrow keys
Station list
Memory listMemory listRDS regional
s36c.b.book Page 10 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
11
– Press on the button , doing so always chooses the
frequency for the heard radio statio
n which offers the best reception
at the present time.
– When pressing on the button , the unit attempts to hold a radio
station emitting regionally long en
ough until the reception quality is
so bad, that there is a risk of a program loss.
Delete stored stations – Press the function key and confirm the following safety interroga-
tion in order to delete all radio stations stored in the memory list.
Tra f f i c s t a t i o n s e t - u p sPress the range selector key and then the range selector key
.
Switching the traffic announcements on or off A tick in the check box
7 indicates that the traffic radio function is already switched
on. Dynamic route Opens a pop-up window where it is considered if the TMC traffic reports, received during the route calculat
ion, are to be entered.
Screen set-upsPress the button in the
RADIO
mode and then the function keys
and .
Brightness – Press the function key and select the desired setting for
brightness (5°stages) in a pop-up window.
– A light sensor, which is located in the top right corner of the front
panel, is used for the automati
c correction of the brightness
depending on the light conditions in the vehicle.
Day/Night – Press on the func tion key and s el ec t a setting in the pop-up
window.
– Press the function key if switching the headlights on and off
should also change the map display from night to day design.
– Press on the function key
or to manually determine the
night and day design of the map display.
Confirmation tone – Press on the function key and select a setting in the
pop-up window.
– Press or to switch the tone for confirmation of a function key
operation on the screen on or off.
Media set-upsPress the button in the
MEDIA
mode.
Function keys in the menu°-°Media•
- a tick in the check box
7 means that the function of the
traffic information is switched on.•
- Check box for setting the play function mode Scan,
Mix and Repeat incl. sub-folder (“switched
on”) or without sub-folder (“switched
off”).•
- Setting the volume of the exte
rnal audio source (audio source
AUX is located on the unit).
Automatic
Fix
Delete memoryAllTRAFFIC
SETUP
Traffic information (TP)
˜ Dynamic routeSETUP
System
Screen
Brightness
Day/Night
Automatic
Day
Night
Confirmation tone
On
OffSETUP
Traffic information (TP)Scan/Mix/Repeat incl.

AUX Volume
s36c.b.book Page 11 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO
13
Range selector key RADIORadio modeRetrieve radio stationCall up main menu RADIO and choose frequency range – Press the range selector key . The currently heard radio station
is displayed in the middle of the screen
⇒
page 7, fig. 2
.
– Press the range selector key
to change the frequency range.
Alternatively, press on the function key in the main menu RADIO
and select or in the pop-up window.
Changing radio station – By briefly pressing the function ke
ys or , you can change to the
previous or following radio station of the selected frequency band.
– If the symbol “
TP” is displayed on the screen, you can only change
over to the radio stations
with traffic announcements.
– If the symbol “
ƒ @ „” is displayed on the screen, you can only
change over to the stored radio stations.
Selecting a radio station from the station list – If you wish that all the presently receivable radio stations are
displayed, press on the function key and then on the func-tion key . The list “skips” directly to the display of the currently heard radio station.
– Select the desired radio station using the menu control button . Change radio station in the memory list – Press the function key and then the function key and
select the desired radio station using the function keys - .
Manual station finding – If you wish to set the radio statio
n manually using its frequency, press
the function key and then the function key .
– Set the radio station using the menu control button or using the
arrows and on the unit.
BAT-20H1064
Fig. 5 Menu radio: Function key band
BAT-20H1064
Fig. 6 FM station list
RADIO
AA
RADIO
Band
FM
AM
ƒ
„
Freq. Band
FM/List
A10
Extras
Memory1
24
Extras
ManualA10
ƒ
„
s36c.b.book Page 13 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO
15
– You can select the station stored on one of the station keys to
in the main menu
RADIO
by briefly pressing the desired station key.
Calling up available stati
ons from the memory list
– Press the button and then the button and the func-
tion key .
– Select the desired radio station using the menu control button .RDS function– If you wish to switch the display of additional information to a radio
station on or off, press the button
, the function is displayed in the
top right corner of the screen by the letter “i”.
RDS (“
Radio
Data
System”) serves to transmit program identification and additional
services therefore also enabling automatic tracking of stations. In the event of sufficiently satisfactory reception, the suitable RDS radio stations will display the station name instead of the station frequency. If a radio station sends additional information via the RDS function while a station is being stored, it can occur that the name
of the radio station is later displayed
incorrectly in the memory list. In this case, the stored station name can be restored by selecting the desired radio station, wait until the correct station name is displayed as radio text then press the menu control button and a pop-up window is displayed on the screen.Traffic information function TPSwitching traffic information TP
(Traffic Program) on or off
– Press the function key in the
RADIO
mode.
– Briefly press on in the opening pop-up window to switch the
traffic information on or off.
The display “
TP” in combination with a station name (e. g. in the station or memory
list), indicates a traffic information station. Irrespective of which radio station is heard,
an additional receiver part in the unit
ensures that a traffic information station can always be received as long as the traffic information function is switched on. The functionality of the function for the traffic information “
TP” is displayed at the
top right in the screen. If no traffic information station can be re
ceived because, for
example, radio recep-
tion is interrupted in general, “
No TP
” will be displayed instead of “
TP”. Remember
that car parks, tunnels, high buildings or
mountains can interrupt the radio signal
up to the total loss of reception. Incoming traffic announcement If you wish to interrupt the transmission of the traffic announcement, press on the function key in the pop-up window
Traffic announcement
. The traffic infor-
mation function remains available and a following traffic announcement is replayed if a random source is switch
ed on. Pressing the function key will
switch off the traffic information function permanently.
1
24
RADIO
Freq. Band
FM/List
A10
º
A10
Station name stored
Extras
TP
Cancel
TP off
s36c.b.book Page 15 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA
17
Range selector key MEDIAGeneral information for CD operationAudio-CDs (CD-A) and MP3-CDs can be
played in the internal drive.
CD not legible If you insert a CD which cannot be read by
the unit, a pop-up window is displayed
with a note. Press on the function key , the CD is driven to the initial position. If the CD is not taken out within 10 seconds, it is drawn in again for safety reasons.
WARNING
•
The CD player is a 1st class laser produc
t. There is a definite risk of injury
from invisible laser beams if it is opened.•
The CD player contains no parts that have to be serviced or repaired.
Please contact your speciali
st garage if a mechanical
defect occurs or the CD
player has to be repaired.
Caution
•
Inserting a second CD while a CD is being ejected can destroy the CD drive in
the unit. Please note that the CD ejecti
on lasts a few seconds after pressing the
Eject button
. During this time the lock in fr
ont of the CD case is open. It is
essential that you wait until the CD has been
fully ejected before you try to insert a
new CD.•
If the CD drive becomes me
chanically defective or
a CD has been inserted
incorrectly or not fully, “
Fa u l t : ° C D
” will be displayed on the screen. Please check the
CD and place it again correctly and fully into the drive. If “
Fa u l t : ° C D
” is indicated
again, please contact your Škoda Service Partner.•
If the inside temperature of the unit is
too high, no CDs will be accepted. The
unit switches into the last active operating mode.
Note
•
If the function key is inactive, no
new Audio CD has been inserted or an
inserted Audio CD is not readable.•
It is possible that CDs protected by copyright and self-made CD-R and CD-RW
are not returned at all or on
ly in certain circumstances.
•
Please observe the following information for the MP3 operation
⇒page 20.
•
Please comply with the national legal copyright requirements in your country.
Main menu MEDIAMain menu MEDIA - Overview
OK
š
CD
BAT-20H1065
Fig. 9 Main menu MEDIA: CD

mode
s36c.b.book Page 17 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA
18
Calling up the main menu MEDI
A and changing the media source
– Press the range selector key to switch to the main menu
MEDIA
. The last used audio source will continue to play.
Buttons on the unit for controlling the current audio sources The arrow keys on unit or will always affect the currently heard audio source, irrespective of the current menu used. - briefly press to go to the beginning of
the current track, press repeatedly to
return to the beginning of the previous track. - brief pressing changes over to the beginning of the next track.When in the menu of the currently played audio source it is also possible to change titles using the setting up button. - by briefly pressing, you can select the display for the additional information of the audio sources. Selectable audio sources in the menu AUDIO
CD - changes over to an inserted CD. CD 1-6
* - changes over to a connected external CD changer.
SD card
- changes over to an inserted memory card.
, or * - changes over to a connected external audio source.
Operating an externally connected audio
source is possible, wi
th certain restric-
tions, via the radio navigation unit and depends largely on the type of the connec- tion. Additional function keys in the AUDIO menu
- opens a pop-up window wher
e the random play function
Mix
, the auto-
matic play
Scan
or the replay of the track or the folder can be started.
- opens the list of the tracks for the current audio source in order to select
another track.Inserting or ejecting a CDInserting the CD – Push a CD with the written side facing
up as far as po ssible into the CD
case until it is automatically drawn in
. The play function will start auto-
matically.
Taking out the CD – Press the button to move the CD
in the internal CD drive into the
Eject position.
If a CD is not taken out in the initial position, it will be reinserted after approximately 10 seconds for safety reasons.Inserting or removing a memory cardInserting a memory card – Push the memory card into the me
mory card case with the trimmed
edge to the front top, until it is locked in position. The play function will start automatically.
Taking out a memory card – Press the button and then the function key .
BAT-20H1066
Fig. 10 Selectable sources in

the menu MEDIA
MEDIA
ƒ
„
ƒ„ºFFF

HAUX
MDI
BT audio
ExtrasSelect
šSETUP
System
s36c.b.book Page 18 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA
20
– Press on the function key to open the appropriate higher priority
folder.
– By pressing repetitively, you can reach the root folder of the
played medium while moving from folder to folder. Then the function key is inactive.
Repeat track – Press the function key in the
Media
menu and then the func-
tion key (repeats the current track) or (constantly repeats all the tracks in the folder).
Random play function – Press on the function key in
MEDIA
.
– Press on the function key in the pop-up window. All titles of the
current audio source will now be played in random order.
– If you press the function key in the pop-up window, the
tracks of the current folder are played in random order.
– Use the function key to terminate the function of the current
title. The normal play function continues with the current title.
Automatic play (Scan function)– Press on the function key in
MEDIA
.
– Press on in the pop-up window. All the titles of the current audio
source are played for approximately 10 seconds.
– Press to terminate the play function of the current title. The
normal play function continues with the current title.
Alternatively, start and end the automatic
play by briefly pressing the menu control
button .MP3 and WMA dataGeneral information for MP3 operationRequirements for the MP3 data and data carrier•
CD-ROM, CD-R, CD-RW with a capacity of 650 MB and 700 MB.
•
The CDs must correspond to the ISO 9660
Level 1 or Level 2 standard as well as
the Joliet data system (single and multi-session).•
Data names must be no longer than 256 characters.
•
The list structure is restricted
to a depth of 8 list levels.
•
An MP3 CD must not have more than 50°folders and 500°data.
•
A memory card must not have more than 5°000°folders and 15°000°data. Thus,
one folder must not have more than 6°000 data.•
The name of the artist, the album and the title of the reproduced MP3 data can
be shown as ID3 tag, providing this information is available. The list and data name will be displayed if
there is no ID3 tag.
•
Playlists are not supported.
•
WMA data (
Windows
Media
Audio) can also be played
even if the copyright is
additionally protected
by the DRM procedure (
Digital
Rights
Management). Such
WMA data is not supported by the unit. Bit rate (data flow per time unit)•
The system supports MP3 data with bit rates of 32 to 320 KB/s as well as MP3
data with variable bit rates.•
The indicated playing time data with variable bit rates is not reliable.
Up
Up
Up
Extras
Repeat track
Repeat folder
MIX
ExtrasMix all
Mix folder
b MixExtras
Scan
bScan
A10
s36c.b.book Page 20 Thursday, April 9, 2009 2:50 PM

Range selector key NAV (Navigation)
28
Starting the search – If you have completed your entries in the search mask, press on the
function key . A pop-up window will open and the search for the points of interest, which correspond to the entry, will start.
– The surrounding area where the points of interest are searched for is
displayed and continues to increase.
– If you press on the function key the search will be terminated
without a display.
– From the moment when all the points of interest are found, which
correspond to the entered text, they are displayed in the list.
– T h e s e a rc h e x t e n d s u p t o a d i s t a n c e o f a p p ro x . 7 5 k m f ro m t h e e n t e re d
position. You can interrupt the search of the displayed distance by pressing the function key .
– When the search has ended, the function key changes to the
function key .
Selecting a point of interest from the search results – Selecting the menu point from the list of the points of interest found,
starts the route guidance.
– If several points of interest were found, they will first of all be displayed
in a list. At the top of the list you ca
n find the points of interest closest
to the entered search area (distance and direction information refer to linear distance).
– If you press the function key , the details for the point of
interest are displayed. A route guidance is started after pressing the function key .
– In the list of the points of interest
or in the display of the details for a
destination, you can store the point of interest in a destination memory by pressing the function key .
Destination memoryStore last destinations– Press on the function key
Last destins.
while in the main menu
Navigation
.
– Press one of the displayed destinations. The unit will change to the
map display and the route guidance to
this travel destination will start
automatically.
– If you press the function key , the detailed information for the
destination is displayed.
– If you wish to store a destination, press on the function key .Store destinations in the destination memory– If you press the function key , an input mask for entering the
destination name opens.
– After entering the destination
name, press the function key .
– If you wish to change the destination name, press the function key
and select your ow
n destination name.
Edit stored destinations– Press the function key
Destination memory
while in the main
menu
Navigation
. A list of the manually stored destinations in the
destination memory is displayed.
– Press one of the displayed destinations. The unit will change to the
map display and the route guidance to
this travel destination will start
automatically.
Search
Abort
Stop
Stop
Details
Details
Start
Store

Details
Store
Store
OK
Delete

s36c.b.book Page 28 Thursday, April 9, 2009 2:50 PM