light SKODA SUPERB 2010 2.G / (B6/3T) Amundsen Navigation System Manual

General information
4
precondition that the housing has not be en damaged and no unauthorised attempts
have been made to carry out repairs.
Note
Damage within the meaning of the warranty must not be the result of improper
handling of the system or from unprofessional repair attempts. It is also essential that
there is no external damage.Information on how to operate the radio navigation systemThe requirements of today's road traffic demand the driver’s full concentration at all
times.
Apart from the availability entertainmen t, the extensive and demanding equipment
details of this radio navigation system also offer a wide range of information, which will
help you to reach your destination quickly and safely.
Only if the traffic situation allows it, should you operate the radio navigation
system with its wide range of possibilites.
The volume settings must be selected in such a way that audible signals from the
outside, e.g. a Martins horn from utility vehicles (police cars, ambulances and fire
brigade), can be heard at all times.
WARNING
•
Please concentrate fully at all times on your driving! As the driver you are
fully responsible for road safety. Only use the functions of the radio navigation
system in such a way that you are always in full control of your vehicle in all
traffic situations!
•
The following must always have priority over the driving recommendations:
•
the road traffic legi slation, even if the drivin g recommendations contradict
the StVO,
•
the actual acknowledgement of traffic si gns, light signals or signs placed by
the police at the relevant location,
•
the facts and circumstances prevai ling at the relevant location.
Before using the radio navigation system•
Please observe the respective traffic regulations when driving.
•
Street and location names can be changed. It is therefore possible that the names
stored on the CD might not correspond to the changed names.
•
The route calculated by the radio navi gation system is a recommendation for
reaching the intended destination. While driving please pay attention to stopping
restrictions, traffic lights, one-way streets, lane changes, bodies of water and ferries,
railways etc.Caution
•
Press the buttons and the keys of the unit gently in order to avoid damaging them.
Gentle pressure on the appropriate key is sufficient to operate the unit. Please note that
the control buttons have predetermined breaking points, in order to reduce the risk of
injury.
•
Do not use any pointed or sharp-edged objects to operate the touch-screen. Slight
finger pressure sufficient to operate the equipment. A display on the screen, which
cannot be called up by pressing the button, is therefore not available at that time.
•
Please note that a dirty or scratched navigation CD can considerably impair the
speed and the functions of the radio navigation system.
Screen careTreat the screen with great care, because de nts and scratches can occur through finger
pressure or contact with sharp objects.
The screen can be cleaned with a soft clot h and finger marks can be wiped away with
pure alcohol.
Note
Do not use solvent such as turpentine or petrol as they will attack the screen surface.
s34g.6.book Page 4 Thursday, January 14, 2010 8:48 AM

Range selector key SETUP
10
Delete stored stations
– Press the function key and confirm the following safety interrogation in order to delete all radio stations stored in the memory list.Setup Telephone*Call up the Setup Telephone menu by pressing the range selector key and the
range selector key .Entering the voice mailbox number– If you want to enter the voice mailbox number (this number depends on the type
of the mobile phone network) in a mobile phone, press the function key . The entry of the voice mailbox number is intended for
listening to the messages left on a mobile phone.Updating telephone book in the unit– Press on the function key to update all entries in the unit, the
telephone book of the mobile phone or th e SIM card entered since the last connec-
tion. This procedure can take a few minutes.
– Confirm the following safety interrogatio n. The “old” data in the telephone book
can still be selected at the unit while the data is being updated.Delete call lists– Press on the function key .
– If you confirm the following safety interrogation by pressing , the stored call numbers of all calls made and calls accepted in the unit will be deleted.Deactivating the telephone module– After pressing the function key the mobile phone
deregisters from the network (this function is only available for the universal tele-
phone preinstallation GSM III).Factory settings– Sets the telephone preinstallation to the basic setting.
Note
The selection possibilities of the mobile phone set-up depend on the relevant type of
the universal telephone preinstallation.Setup traffic programmePress the range selector key and then the range selector key .
Switching the traffic announcements on or off
A tick in the check box
=
indicates that the traffic pr ogramme function is already
switched on.
Dynamic route
Opens a pop-up window where it is consider ed if the TMC traffic reports, received
during the route calculation, are to be entered.
Setup DisplayPress the button in the RADIO mode and then the function keys and
.Brightness– Press the function key and select the desired setting for brightness (5°stages) in a pop-up window.
– A light sensor, which is located in the top ri ght corner of the front panel, is used for
the automatic correction of the brightness depending on the light conditions in the
vehicle.Day/night– Press on the function key and sele ct a setting in the pop-up window.
– Press the function key if switching the headlights on and off should also change the map display from night to day design.
– Press on the function key or to manually determine the night and day design of the map display.
Delete presetsAll
PHONE
SETUP
Enter voice mailbox number
Load telephone bookDelete call lists
Delete
Deactivate the telephone module
TMC
SETUP
Traffic announcements (TP)
˜Dynamic routeSETUP
System
Screen
BrightnessDay/Night
Automatic
Day
Night
s34g.6.book Page 10 Thursday, January 14, 2010 8:48 AM

Range selector key SETUP11
Confirmation tone
– Press on the function key and select a setting in the pop-up
window.
– Press or to switch the tone for confirmation of a function key operation on the screen on or off.Media set-upsPress the button in the MEDIA mode.
Function keys in the menu°-°Media•
- a tick in the check box
=
means that the function of
the traffic programme is switched on.
•
- Check box for setting the play function mode Scan, Mix
and Repeat incl. sub-folder (“switched on”) or without sub-folder (“switched off”).
•
- Setting the volume of the external audio source (audio source AUX
is located on the unit).
•
* - Setting the volume of the external audio source (the audio source
MDI is located under the armres t of the front seats or in a storage compartment on the
front passenger side).
•
* - enables a wireless transfer of MP3 data to the tele-
phone preinstallation. Enables the audio play function by means of Bluetooth interface
of portable units (mobile phones) which support the protocol A2DP.
Navigation settingsPress the button in the Navigation mode.
Function keys in the menu°-°Navigation•
- determine the criteria according to which a route is to be calcu-
lated and what types of destinations you wish to assign.
•
, , and - route
criteria, dynamic route guidance, route wi thout motorways and route without toll
roads/ferries.
•
- Setting the volume of the navigation announcements.
•
- changes between day and night display, as well as automatic, if the
map display changes automatically accordin g to the setting of the light switch.
•
- displays a point of interest on the map.
•
- changes the map scale automatically depending on the speed and the
driven route (Motorway trip: small map scale - City center: large map scale).
•
- the speed limit for the current section of the route is indicated
at the top left of the screen.
•
- during a route guidance, either the arrival or the driving time is
shown in the map display.
•
- Enter home address.
•
- you can start a virtual (apparent) route guidance in the demo mode.
Virtual route guidance will be repeated when reaching the fictive travel destination.
Stop virtual route guidance normally and de activate the demo mode to restart “real”
route guidance. As in this case the unit must first reorient itself it can take some time,
depending on the number of the currently tracked satellites, until the unit has again
found the real location. Drive a short distance.
•
- Entering a fictive (invented) starting point in the demo
mode.
•
- Deleting the destination memory or the list of the last
destinations.
•
- Display of information via the data base on CD or SD card,
delete the data base of the SD card or copy the data.
Route criteria
Fa st : calculates the fastest route to the dest ination, even if a detour is necessary.
Short : calculates the shortest route, even if a longer driving time is necessary. Please
note that the setting “Short route” during route guidance can sometimes lead to unex-
pected results.
Economical : calculates a route with a driving time as minimal as possible and a driving
distance as short as possible.
Confirmation tone
On
OffSETUP
Traffic announcements (TP)Scan/mix/repeat incl. AUX volumeMDI volumeActivate Bluetooth audio?
SETUP
Route optionsRoute criteria
Dynamic route
Avoid motorways
Avoid toll roads/ferries
Announcement volumeDay/NightPOIs on mapAutozoomTraffic sign displayTime displayEnter home addressDemo modeDemo mode starting pointDelete destination memoryNavigation data basis
Route criteria
s34g.6.book Page 11 Thursday, January 14, 2010 8:48 AM

Range selector key MEDIA19
Audio menu Select title or audio sourceChange audio source– Press the range selector key to switch to the main menu MEDIA.
– Press one of the top function keys to select the corresponding audio source. The
play function of the selected audio source will continue from the last played point.Opening the selection menu of the available audio sources– When in the Audio menu, press the function key to display the title list of the
currently played audio source. The currentl y played track is shown as highlighted.
– If one of the buttons of the audio source da ta is pressed, the contents of the folder
or the data carrier is displayed.Changing track or selecting track manuallyPress the range selector key to switch to the main menu MEDIA.Select track– Briefly press the arrow key on the unit or while in the MEDIA menu.Fast forward/reverse– Hold the arrow key on the unit or pressed.
– If you have reached the desired title sequence, release the button.Audio CD– Press on the function key , in order to display the title list of the currently
played audio CD.
– Select the desired track from the title list using the menu control button .
MP3 Data: Select track– Press on the function key , in order to display the title list with the currently
played title and, if necessar y, to display the sub-folder contained in this folder.
– Press on the display of a data folder to open it.
– Press on the function key to open the appropriate higher priority folder.
– By pressing repetitively, you can reach the root folder of the played medium while moving from folder to folder. Then the function key is inactive.Repeat track– Press the function key in the Media menu and then the function key
(repeats the current track) or (constantly repeats all the
tracks in the folder).Random play function – Press on the function key in MEDIA.
– Press on the function key in the po p-up window. All titles of the current
audio source will now be played in random order.
– If you press the function key in the pop-up window, the tracks of the current folder are played in random order.
– Use the function key to terminate the function of the current title. The normal play function contin ues with the current title.Automatic play (Scan function)– Press on the function key in MEDIA.
– Press on in the pop-up window. All th e titles of the current audio source are
played for approximately 10 seconds.
– Press to terminate the play function of the current title. The normal play
function continues with the current title.
Alternatively, start and end the automatic play by briefly pressing the menu control
button .
MEDIA
Select
MEDIA
ƒ
„
ƒ
„
Select
A10
SelectUp
Up
Up
Extras
Repeat track
Repeat folder
MIXExtrasMix allMix folder
b Mix
Extras
ScanbScanA10
s34g.6.book Page 19 Thursday, January 14, 2010 8:48 AM

Range selector key NAV (Navigation)23
Range selector key NAV (Navigation)OverviewSafety information regarding the use of the navigation systemThe route is recalculated each time if you ignore driving recommendations or change
the route. This process takes only a few seconds. Driving recommendations can only
then be re-transmitted.
Incomplete navigation data
The navigation system cannot receive any data from GPS satellites if you drive for
longer periods under thick forest canopy or when your vehicle is in a garage, under-
pass or tunnel. In this case, the navigation system orientates itself solely with the help
of the vehicle sensors.
In regions not at all or only partially digitalised and stored as such on the navigation
CD, the navigation system will try to provide guidance to the destination. Please note
that under these circumstance s the guidance to the destination may not be completely
correct if, for example, one-way streets and road categories (motorway, country road
etc.) are not at all or only partially included in the navigation data used.
WARNING
•
Always concentrate fully on your drivin g. Inattention by the driver can lead
to accidents and injuries.
•
Do not allow yourself to be distracted or loose your concentration, pay
attention to the traffic situation and do not carry out settings or use the radio
navigation system.
•
Only use the radio navigation system if road, weather and traffic situations
permit this and you are not distracted.
•
The various volume settings must be selected in such a way that audible
signals from the outside, such as e.g. a Martins horn from police cars and fire
brigade, can be heard at all times.
WARNING
•
Please observe the legal requirements for road traffic when following the
driving recommendations provided by your radio navigation system.
•
The driving recommendations provided may vary from current situations,
e.g. due to road works or out of date navigation data. In such a case, always
observe the traffic regulations and ignore the driving recommendations.
•
Traffic signs and traffic regulations always have priority over the driving
recommendations provided by the navigation system.
•
Route guidance is subject to consta nt changes despite the information
about one-way streets, pedestrian zone s etc. stored on the navigation CD.
Information on traffic lights, stop and right of way signs, parking and stopping
restrictions as well as lane constrictions and speed restrictions is not included
in the radio navigation system.
•
Adjust your speed to suit weather, road and traffic conditions. Do not allow,
for example, the radio navigation system to make you drive faster in fog - risk
of accident!
GeneralYou can continue to listen to the radio or play CDs during the route guidance
When entering an address (city, street), on ly those letters or symbols which make up a
logical entry will be presented. A list of poss ible names will be shown. Do not forget to
enter the blank space in names made up of more than one word, such as High
Wycombe.
The route will be recalculated if you leave or disregard the route that was originally
calculated. This process takes only a few seconds.
The last voice response can be repeated by pressing the button or the menu control
button . The volume of a navigation reco mmendation can be changed whilst it is
being made.
The GPS satellites will not be able to reach the aerial once you are in a tunnel or under-
ground garage. The unit will orientate itself via the wheel sensors.
A10
s34g.6.book Page 23 Thursday, January 14, 2010 8:48 AM

Range selector key NAV (Navigation)29
– You can determine which types of destinations should be provided or not by using
the function keys , and
. These types of destinations will, however, be used for the
route calculation if there is no other logica l route to the destination (e.g an island is
to be used without using a ferry).
Determining the parameters for the route calculation•
Fa s t : calculates the fastest route to the dest ination, even if a detour is necessary.
•
Short: calculates the shortest route, even if a longer driving time is necessary.
Please note that the setting “Short route” during route guidance can sometimes lead
to unexpected results.
•
Economical : calculates a route with a driving time as minimal as possible and a
driving distance as short as possible.
Route guidance
Select the destination and start the route guidance. The unit will switch over to the map
display.
– You can change the scale of the map di splay by turning the menu control button
.
– The last navigation anno uncement is repeated if you press the menu control
button .
– If you press the range selector key , you can select between the menu
or .
– If you press the range selector key , you can change between the operating modes of the map by pressing the symbol
z.
If you press the function key in the operating mode , you can select
between the map displays.
•
,
•
and (different viewing angles of the map),
•
- during the active route guidan ce, the calculated route from the
current vehicle position to the entered destination is displayed,
•
.
The route to be driven is highlighted during the route guidance, the symbol
9
shows
the current vehicle position, the symbol

shows the distance to the destination and
the symbol

shows the estimated time of arrival or the driving time.
Stretches of the road ahead can also be blocked manually during a route guidance
⇒ page 30.
Stop route guidanceSelect the destination and start the route guidance. The unit will switch over to the map
display.
– The route guidance is interrupted and the function key changes to “ Start” by
pressing the range selector key and then the function key .
– If you press on the function key the route guidance will continue at the
current position.
˜ °Dynamic°route
˜°Avoid motorways
˜°Avoid toll roads/ferries
Fig. 15 Map display with function keysFig. 16 Map display during the route
guidance
A10
A10
NAV
Extras
Exit
NAV
Extras
NAV
2D north2D heading
3D heading
Overview mapMain menu
NAV
Exit
Start
s34g.6.book Page 29 Thursday, January 14, 2010 8:48 AM

Range selector key PHONE
32
Call a call number from the telephone book
– Turn the button to the right in order to display further entries in the menu Tele-
phone book .
– Press on the function key to select a telephone book entry via a search mask.
– Press on the display of a telephone book entry. If only one telephone number is stored during a telephone entry, this telephone number was selected. If several
telephone numbers are stored during a telephone entry, a menu will be opened
with these numbers.Display information relating to a telephone book entry– If you press the function key the telephone numbers, which are stored during this entry, will be displayed.
– If you press on the entry of a call number, the connection to this call number will
be established.Search for an entry in the telephone book– Press on the function key in the menu Telephone book to select a telephone
book entry via a search mask.
– Press a selectable character on the keypad while in the search window to accept it
in the entry line.
– Press the function key to open the input mask for entering numbers and special characters. Press , to change again to the letter input mask.
– Press the function key to open the inpu t mask for entering Cyrillic letters. In
order to return to the input mask for Latin letters, press .
– By pressing the function key , the characters in the entry line are deleted from right to left, starting from the position of the cursor.
– By pressing on the button , you can chan ge in the telephone book to an entry
which is highlighted in the edit line.
Adapt a call numberOpen the display of a call number from the te lephone book or a call list as described
in the corresponding chapter ⇒page 32.
– Press the arrow buttons or to move the character entry cursor in the entry line.
– Press on a character inserted into the ke ypad to accept it behind the character
entry cursor in the entry line.
– The connection to the disp layed call number will be established as soon as you
press the function key .Call listsDepending on the type of the mobile phon e and the telephone preinstallation, only
the telephone numbers of calls which were mi ssed, selected and accepted by the tele-
phone preinstallation in the vehicle can be stored. The call lists stored in a mobile
phone will not be transferred to the vehicle.
If the call number from a ca ll li st i s s to red in the te le phone book the s tored name in the
telephone book is displayed instead of the call number.
Call lists are always assigned to a user profile and are only displayed once the corre-
sponding SIM card is connected again with the mobile phone preinstallation.Holding a conversationIf you have started the process of connecting to a call number or accepted a call, the
main menu PHONE will change to the display Phone conversation.Incoming phone call– An incoming phone call will be displayed on the display by “Ringing” followed by
the call number of the caller. If the number of the caller is stored in the telephone
book, the name of the caller will be displayed instead of the call number.
– Press the function key to accept the call.
– Press the function key to reject the call.
FindDetailsFind;A-Z~
ABC
DeleteOK
‚
b
^
s34g.6.book Page 32 Thursday, January 14, 2010 8:48 AM