inflation pressure SKODA SUPERB 2013 2.G / (B6/3T) User Guide

WARNING■When the indicator light  illuminates, immediately reduce the speed and
avoid sudden steering and brake manoeuvres. Stop the vehicle as soon as
possible and inspect the tyres and their inflation pressure.■
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light  may light up after a delay, or not at all.
CAUTION
■
The tyre control display does therefore not replace the regular tyre inflation
pressure control, as the system cannot detect an even loss of pressure.■
The system cannot warn in case of very rapid tyre inflation pressure loss, e.g. in
case of sudden tyre damage. In this case carefully bring the vehicle to a standstill
without sudden steering movements or sharp braking.
■
To ensure a proper functioning of the tyre control display, it is necessary to re-
peat the basic setting every 10000 km or once a year.

Spare wheel
Fig. 172
Boot: Spare wheel
First read and observe the introductory information and safety warn-
ings on page 220.
The spare wheel is located in a well under the floor covering in the boot and is
fixed in place with a special bolt » Fig. 172.
Take out the wheel
›
Open the boot lid.
›
Lift up the floor in the luggage compartment.
›
Remove the box with the tool kit.
›
Unscrew the bolt » Fig. 172 in a counterclockwise direction.
›Take out the wheel.
Stow the wheel›
Stow the replaced wheel in the spare wheel well with the rim facing down.
›
Screw the bolt » Fig. 172 in a clockwise direction until the wheel is safely se-
cured.
›
Place the box with the tool kit back into the spare wheel and secure it with the
tape.
›
Fold back the floor in the luggage compartment.
›
Close the boot lid.
Fit a wheel in the appropriate dimensions and design as soon as possible.
If the dimensions or design of the spare wheel differ from the tyres fitted to the
vehicle (e.g. winter tyres or low-profile tyres), it must only be used briefly in the
event of a puncture and if an appropriately cautious style of driving is adop-
ted »
.
Spare wheel
A warning label is displayed on the rim of the temporary spare wheel.
Please note the following if you intend to use the temporary spare wheel. › The warning label must not be covered after installing the wheel.
› Be particularly observant when driving.
› The inflation pressure for the temporary spare wheel is identical to the maxi-
mum inflation pressure for the standard tyres.
› Only use this temporary spare wheel to reach the nearest specialist garage, as it
is not intended for long-term use.
WARNING■ Never use the temporary spare wheel if it is damaged.■If the dimensions or design of the temporary spare wheel differ from the fit-
ted tyres, never drive faster than 80 km/h (or 50 mph).■
Avoid accelerating at full throttle, sharp braking and fast cornering.
CAUTION
Observe the instructions on the warning sign of the temporary spare wheel.
224General Maintenance

›Insert the adapter B
» Fig. 182 with its toothed side fully into the inner tooth-
ing of the safety wheel bolt A until the stop so that only the outer hexagon is
jutting out.›
Push the wheel wrench onto the adapter
B
up to the stop.
›
Loosen or tighten the wheel bolt » page 230.
›
After removing the adapter replace the cap on the anti-theft wheel bolt.
›
Have the tightening torque checked with a torque wrench as soon as possible.
Note
■
Make a note of the code number hammered into the rear side of the adapter or
the rear side of the anti-theft wheel bolt. This number can be used to purchase a
replacement adapter from ŠKODA Original Parts if necessary.■
We recommend that you always carry the adapter for the wheel bolts with you
in the vehicle. It should be stowed in the vehicle tool kit.
■
The anti-theft wheel bolt set and adapter can be purchased from a ŠKODA Part-
ner.

Tyre repair
 Introduction
This chapter contains information on the following subjects:
Breakdown kit
233
Preparations for using the breakdown kit
233
Sealing and inflating the tyre
233
Check after 10 minutes' driving
234
Use the breakdown kit to reliably repair tyre damage caused by foreign bodies or
a puncture with diameters up to approx. 4 mm.
A repair made using the breakdown kit is never intended to replace a permanent
repair on the tyre. Its purpose is to get you to the nearest specialist garage.
The wheel must not be removed during repair.Do not remove foreign bodies , e.g. screws or nails, from the tyre.
The breakdown kit must not be used under the following circumstances. › There is damage to the rim.
› The outside temperature is less than -20 °C.
› The tears or punctures are greater than 4 mm in size.
›
There is damage to the tyre wall.
› Driving with very low tyre pressure or with a completely flat tyre.
› If the use-by-date (see inflation bottle) has passed.WARNING■
A tyre filled with sealant has the same driving characteristics as a standard
tyre.■
Do not travel faster than 80 km/h.
■
Avoid accelerating at full throttle, sharp braking and fast cornering.
■
Check the tyre pressure after driving for 10 minutes.
■
The sealant is hazardous to heath. Remove immediately if it comes into con-
tact with the skin.
For the sake of the environment
Used sealant or sealant whose expiry date has passed must be disposed of in ac- cordance with environmental protection regulations.
Note
■ Observe the manufacturer's usage instructions for the breakdown kit.■A new bottle of sealant can be purchased from ŠKODA Original Parts.■
Immediately replace the tyre that was repaired using the breakdown kit, or con-
sult a specialist garage about repair options.

232Do-it-yourself

Breakdown kitFig. 183
Components of the breakdown kit
First read and observe the introductory information and safety warn-
ings
on page 232.
The kit is located in a box under the floor covering in the luggage compartment.
Components of the breakdown kit Valve remover
Sticker with speed designation “max. 80 km/h”/“max. 50 mph”
Inflation hose with plug
Air compressor
Tyre inflation hose
Tyre inflation pressure indicator
Air release valve
ON and OFF switch
12 volt cable connector
Tyre inflator bottle with sealing agent
Replacement valve core
The valve remover
1
has a slot at its lower end which fits into the valve core.
This is the only way in which you can remove and re-install the valve core from
the tyre valve. The same also applies to the replacement valve core
11
.

1234567891011Preparations for using the breakdown kit
First read and observe the introductory information and safety warn-
ings
on page 232.
The following preparatory work must be carried out before using the breakdown
kit.
›
Park the vehicle as far away as possible from the flow of traffic. Park on as flat and firm a surface as possible.
›
If you are in flowing traffic, switch on the hazard warning light system and setup the warning triangle at the prescribed distance! The national legal require-
ments must be observed.
›
Let all of the occupants get out. While changing a tyre, the occupants of the
vehicle should not stand on the road (instead they should remain behind a crash
barrier).
›
Switch off the engine and move the gearshift lever into Neutral or move the se-
lector lever on the automatic gearbox into position P.
›
Firmly apply the handbrake.
›
Check that you can carry out the repairs with the breakdown kit » page 232.
›
If a trailer is connected, uncouple it.
›
Remove the breakdown kit from the boot.
›
Stick the sticker
2
» Fig. 183 on page 233 on the dash panel in view of the driv-
er.
›
Do not remove the foreign body, e.g. screw or nail, from the tyre.
›
Unscrew the valve cap.
›
Use the valve remover
1
to unscrew the valve core and place it on a clean sur-
face (rag, paper, etc.).

Sealing and inflating the tyre
First read and observe the introductory information and safety warn-
ings
on page 232.
Sealing
›
Forcefully shake the tyre inflator bottle
10
» Fig. 183 on page 233 several times.
›
Firmly screw the inflation hose
3
onto the tyre inflator bottle
10
in a clockwise
direction. The film on the cap is pierced automatically.
›
Remove the plug from the inflation hose
3
and plug the open end fully onto
the tyre valve.
›
Hold the bottle
10
with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre. 
233Emergency equipment and self-help

›Remove the empty tyre inflator bottle from the valve.›Screw the valve core back into the tyre valve using the valve remover 1.
Inflating›
Screw the tyre inflation hose
5
» Fig. 183 on page 233 of the air compressor
firmly onto the tyre valve.
›
Check that the air release valve
7
is closed.
›
Start the engine and run it in idle.
›
Plug the connector
9
into 12 Volt socket » page 77, Cigarette lighter .
›
Switch on the air compressor with the ON and OFF switch
8
.
›
Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved. Max-
imum run time of 8 minutes » !
›
Switch off the air compressor.
›
If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation
hose
5
from the tyre valve.
›
Drive the vehicle 10 metres forwards or backwards to allow the sealing agent to
“distribute” in the tyre.
›
Firmly screw the tyre inflation hose
5
back onto the tyre valve and repeat the
inflation process.
›
If you cannot reach the required tyre inflation pressure here either, this means
the tyre has sustained too much damage. You cannot seal with tyre with the breakdown kit »
.
›
Switch off the air compressor.
›
Remove the tyre inflation hose
5
from the tyre valve.
Once a tyre inflation pressure of 2.0 – 2.5 bar is reached, continue the journey at a
maximum speed of 80 km/h (50 mph).
Check the tyre inflation pressure after driving for 10 minutes » page 234.
WARNING■
The tyre inflation hose and air compressor may get hot as the tyre is being
inflated – there is a risk of injury.■
Do not place the hot tyre inflation hose or hot air compressor on flammable
materials – there is a risk of fire.
■
If you cannot inflate the tyre to at least 2.0 bar, this means the damage sus-
tained was too serious. The sealing agent cannot be used to seal the tyre. 
Do not drive the vehicle. Seek help from a specialist garage.
CAUTIONSwitch off the air compressor after running 8 minutes at the latest – there is a
risk of overheating. Allow the air compressor to cool a few minutes before switch- ing it on again.
Check after 10 minutes' driving
First read and observe the introductory information and safety warn-ings
on page 232.
Check the tyre inflation pressure after driving for 10 minutes!
If the tyre pressure is 1.3 bar or less
›
 Do not drive the vehicle! You cannot properly seal with tyre with the break-
down kit.
If the tyre pressure is 1.3 bar or more
›
Adjust the tyre inflation pressure to the correct value (see inside of fuel filler cap).
›
Continue driving carefully to the nearest specialist garage at a maximum speed
of 80 km/h (50 mph).

Jump-starting
 Introduction
This chapter contains information on the following subjects:
Jump-starting using the battery from another vehicle
235
Jump-starting in vehicles with the START-STOP system
236
Jump-starting vehicles with the vehicle battery in the boot
236

234Do-it-yourself

Correct seated position170
Driver171
Front passenger171
Instructions171
Rear seats171
Counter for distance driven12
Cruise control system Activating/deactivating
158
Changing the stored speed158
Storing and maintaining speed158
Switching off temporarily158
Cruise Control System157
Cup holders76
D
DAY LIGHT see Daylight running lights
52
Daylight running lights52
De-icing the windscreen and rear window59
Deactivating an airbag184
Decorative films199
Delayed locking of the boot lid see Boot lid
41
Diesel refer to Fuel
206
Diesel fuel Operation in winter
206
Diesel particulate filter20
display messages20
Digital clock13
Dipstick211
Display12
Service interval30
Distance driven12
Door Child safety lock
36
Closing37
Emergency locking the driver's door240
Indicator light for an open door16
Opening37
Door locking Emergency
240
Doors Emergency locking
240
Driver Steering Recommendation (DSR)151
Driving Abroad
148
Driving through water on streets148
Emissions252
Fuel consumption252
Driving economically Economical gear changing
144
Driving through water148
DSR151
DVD-preinstallation128
E
Economical and environmentally friendly driving 143
Economical driving Ballast
146
Driving at full throttle145
Idling145
Looking ahead144
Regular maintenance146
Saving energy146
Short distances145
Tyre inflation pressure145
EDL151
Electrical power windows46
Button in the driver's door44, 45
Button in the rear doors45
Electric boot lid Force limit
41
Manual operation41
Electric luggage compartment lid Acoustic signals
43
Adjusting the top lid position43
Deleting the top lid position43
Malfunctions44
Operating42
Electric sliding/tilting roof47
Electronic Differential Lock (EDL)151
Electronic immobilizer132
Electronic Stability Control (ESC)150
Emergency Activation of the sliding/tilting roof
242
Changing a wheel229
Door locking240
Hazard warning light system56
jump-starting235
Jump-starting234
Locking the driver's door240
Selector lever-unlocking241
Sliding/tilting roof242
Start engine - KESSY136
Switching off the ignition –KESSY136
Towing the using the tow hitch238
Towing the vehicle236
Tyre repair232
Unlocking the driver's door240
Unlocking the tailgate241
Emergency equipment Fire extinguisher
228
First aid kit227
Jack228
Vehicle tool kit228
Warning triangle227
Emissions252
Engine Running in
142
Engine compartment206
Brake fluid214
Coolant213
Overview209
Vehicle battery215
Engine oil210
Capacity210
Changing212
Checking211
262Index

Storage compartments74
Storage compartment under the passenger seat81
Storage pockets on the front seats82
Storing skis83
Sun screen60
Sun screen in the rear doors61
Sun visors60
Switch see Ignition
132
Switching lights on and off51
Switching off the engine see KESSY
136
Switching off the ignition see KESSY
136
Switching on the ignition see KESSY
135
T
Tailgate TwinDoor
40
Taking care of the vehicle Natural leather
202
Seat belts203
Taking care of your vehicle Automatic car wash system
197
Cavity protection200
Chrome parts199
Cleaning the wheels201
Decorative films199
Door lock cylinders200
Headlight lenses200
High-pressure cleaner197
Plastic parts199
Polishing the paintwork198
Rubber seals199
Taking care of the interior201
Taking care of your vehicle exterior198
Washing196
Washing by hand197
Wash system197
Wax treatment198
Taking care of your vehicles Fabric covers
203
TCS Operation
151
Technical data252
Telephone113, 115
Tilting roof see Electric sliding/tilting roof
47
Tiptronic141
Tools228
TOP TETHER190
Towing236
Towing a trailer162
Towing device Description
162
Drawbar load162
Use and care165
Towing eye Front
237
Rear238
Towing protection39
Traction Control System (TCS)151
Trailer162, 165
13-pin power socket166
driving with a trailer166
Loading165
Safety eye166
Trailer stabilisation167
Transport Luggage compartment
84
Roof rack system96
Transporting children safely186
Turn signal53
Twindoor see boot lid
40
Two-way radio systems110
Type plate252
Tyre load-bearing capacity See Wheels222
Tyre pressure monitor Setting
223
Tyre repair Check pressure
234
Preparations233
Sealing and inflating the tyre233
Tyres220
Inflation pressure221
New222
See Wheels222
Sizes221
Tyre wear indicator221
U
Umbrella Tray
82
Underbody protection201
Unleaded petrol148
Unlock Remote control
33
Vehicle key33
Unlocking Individual settings
35
KESSY34
Unlocking and locking32
Useful equipment Ashtray
77
Car park ticket holder75
Cigarette lighter77
Clothes hook81
Cup holders76
Glasses storage box80
Removable ski bag84
Seat backrest with long-cargo channel83
Storage compartment in the front centre console 76
Storage compartment on the driver's side
75
Storage compartments in the doors75
Using the information system23
267Index