length SKODA YETI 2009 1.G / 5L Columbus Navigation System Manual

Range selector key MEDIA
27
Store and edit audio data (HDD)Store MP3 and WMA data on the hard disk (HDD)Select titles or folders to be saved– Check the available audio sources for titles
or folders which you may wish to store
on the hard disk. You can also select the
complete contents of an installed data
carrier for storing on the hard disk in th
e selection window of
the available audio
sources.
– If you press on the function key behind the display of a title or folder, a pop-up
window will open.
– Pressing in the pop-up window
will start the play function.
– Press in the pop-up window to store the respective title or folder on the hard
disk.
– Press in the following pop-up wind
ow for confirmation that you have
taken note of the message.
Select memory space and save titles– Press , if the title or folder should be saved directly on the first level,
which is the root folder of the hard disk.
– Or press if a new folder should be created for the title or folder. Choose
a name for this folder from the following menu. The newly created folder is opened and the name you choose will be indicated in the title line.
– You can now create another folder (o
ne folder has a maximum of seven sub-
folders) or you can save the selected title or folder in the currently described folder. Press the function key to open the
appropriate higher
priority folder.
– Press the function key if you wish to save the title or folder at the
selected point.
– Press to cancel the saving process of the currently stored title. Once the
saving process has been completed, the
pop-up window will close automatically.
Saving 100 music titles of average length of time (3 - 5 minutes) will take approximately 40 minutes.
If the unit is switched off during the saving
process, the saving process will be termi-
nated with the last fully saved title. Functions and progress display during the memory procedure You can continue listening to
this or another audio source while storing other audio
data. Data names with a length of max.
32 characters can be displayed.
The function key is blocked in the
Audio menu
during the memory procedure.
If the function key is pressed regardless, a pop-up window will open instead of the selection menu where the progress of the
saving process is displayed. If you press
in the pop-up window, the storing proces
s will be cancelled with the last fully
stored title. Press the range selector key twice to close the pop-up window and continue the storing process.Edit stored audio data (titles) and foldersSelect title or folder– Open the selection menu of
the available audio sources
⇒page 23.
– Press on the function key to display the stored titles and folders on the hard
disk.
– Select the title or folder to be processed. Press on the display of a folder
to open it. Press the function key to open the appropriate higher priority folder. The names of the currently opened folders are displayed in the title line.
– Press the function key behind the display of the title or folder you wish to
process. A pop-up window will open.
– The play function can be started and the
title or folder can be copied, renamed or
erased via the pop-up window.
Function keys in the pop-up window:
- starts the play function of
the selected title or folder.
- stores a copy of the title or folder
⇒page 27, “Select memory space and save
titles”.
- opens the input mask to change the title or folder name.
H
PlayCopyContinueEnter file/folderNew folder
FEnter file/folder
Cancel
Select.Select.
Cancel
MEDIA
J HDD
G... Name
F
H
PlayCopyRename
s32k.a.book Page 27 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
50– Press the range selector key in the
map display to insert the split-screen.
– Press the function key at the top left in the split-screen. – In the pop-up window press on to
display the direction arrows in the
split-screen
⇒page 49, fig. 22
.
– Press on in the pop-up window to
display an overview map in the split-
screen with the starting and finishing point.
Press briefly on this map to change its
type of display.
– Press the function key or the range selector key to close the split-screen. Route guidance tour plan When driving to a tour plan, route guidance
will start automatically to the next desti-
nation after reaching a stopover. If an exac
t stopover cannot be reached, it must be
deleted from the tour plan before route guidance continues to the next destination. If route guidance to the next destination has been started manually, only this destination will be approached and all further dest
inations of the tour
plan are ignored.
Note
•
If you have missed a turn-o
ff during route guidance an
d there is no other opportu-
nity to turn at that moment,
continue driving until the navi
gation system offers you an
alternative route.•
The quality of the messages transmitted by the unit depends on the available navi-
gation data and, during traffic problems, also
on the available traffic reports. The radio
stations broadcasting the traffic reports are responsible for the content and quality of the available traffic reports.Dynamic route guidance with TMC use Switching the dynamic navigation on or off– In the main menu
Navigation
press on the function key .
– In the map display, press on or on
⇒page 49, fig. 21
during
a route guidance and on in the pop-up window.
– In the menu
Route options
, press on the function key and select
the desired set-up by pressing yo
ur choice in the pop-up window.
– Press to confirm your input. Traffic problems received via TMC which affect the route are displayed in the map by means of a coloured symbol. Traffic proble
ms, which do not affect the route, are
displayed in the map by means of a grey
symbol. The direction in which a traffic
problem is found, is displayed by means of an arrow in the symbol. The duration of a traffic problem on the route is displayed
in the map by means of continuous PKW
(motor car) symbols
.
 Dynamic route
b Off
When the dynamic navigation is
switched off you will not be advised of traffic prob-
lems affecting your route duri
ng route guidance and you are not directed away from or
through the traffic problems. TMC traffic reports are updated automatically in the unit ⇒ page 51, “Requirements for a dynamic rout
e guidance” and displayed by pressing
the range selector key . If one of the announced traffi
c problems is on your route,
you can also switch on the
dynamic route guidance during the current
route guidance or block the route manually
⇒ page 52, “Manually blocking a stretch of the route”. Dynamic route
b Manual
If the dynamic navi
gation is set to
manual
and you are in route guidance mode you
can select to avoid the announced traffic problems on your route
⇒page 51,
“Requirements for a dynamic route guidance”. If the navigation system is alerted of a tr
affic problem on the calculated route, the
driver will be notified of this by means
of an audible message and information in a
pop-up window. The expected delay incurred in avoiding this traffic problem and the length of the alter- native route will be displayed. The expected time lost when driving through this traffic problem will also be displayed.•
Press to remain on the calculated route and to pass through the
traffic problem.•
Press on for an alternative route to
be calculated taking
into account the
announced traffic problem.
MAP
NAV symbol
Overview
O
MAP
Options
Navigation
 ... /...
Route options
 Dynamic route
OK
TMC
Current routeBypass
s32k.a.book Page 50 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
52Manually blocking a stretch of the routeCongestion ahead– Press on the function key in the ma
p display during a route guidance or
on the function key in the main menu
Navigation
.
– Press on the function key in the pop-up window. An overview
map will be displayed together wi
th the current vehicle position
9 and the travel
destination
3.
– Turn the set button anti-clockwise, move a flag symbol
4 starting from the
travel destination in direction of the current vehicle position. Use the finger to press on the displayed route and the flag symbol
4 will “skip” directly to this point. The
distance taken up by the current congesti
on will be displayed as of the current
vehicle position at the bo
ttom in the touch-screen.
– Press the set button or the function key , when the approximate length of the
stretch of the road to be
bypassed is displayed.
– You will receive an audible announcement
that parts of the route are blocked and
that the alternative route is being calculated.
Permanent congestion– Press the function key and then in the main menu
Navigation
during route guidance.
– - if you wish to add a further blocked section to the
route.
– Locate the start of the congestion
4 by pressing on the
route indicated on the
touch-screen and confirm it by pressi
ng the function key . The end of the
congestion is set in the same way.
– Name of the congestion - you can name th
e congestion with the help of the input
mask for the text entry.
– - finally deletes th
e excluded sections
from the memory of the navigation unit.
– - deletes the congestion entered with the button
Received TMC traffic reports wi
ll be displayed in the map as
traffic problems. Currently
announced traffic problems can also be disp
layed in the list of TMC traffic reports.
... /...
Route
Congestion ahead
A8
OK
Route
Manage blocked routes
Add excluded street section
OK
Delete excluded rd. section/area to be avoidedDelete temporary congestionCongestion ahead
s32k.a.book Page 52 Friday, September 18, 2009 1:54 PM