ABS SKODA YETI 2009 1.G / 5L User Guide

Intelligent Technology
164
offered must not tempt you to take greater risks than otherwise - risk of an acci- dent!
Note
•
All four wheels must be fitted with the same tyres in order to achieve problem-free
operation of the ESP. Differing rolling circum
ferences of the tyres can lead to an unde-
sirable reduction in the engine output.•
Changes to vehicle (e.g. on engine, on th
e brakes, on chassis or another combina-
tion of tyres and wheels) can influence the function of the ESP
⇒page 221, “Accesso-
ries, changes and replacement of parts”.Electronic Differential Lock (EDL)* The electronic differential lock prev
ents an individual wheel from slip-
ping.Models fitted with ESP ar
e equipped with electronic differential lock (EDL).
General The EDL makes it much easier, and sometimes
at all possible, to start off, accelerate
and climb a steep hill when the conditions of the road surface are unfavourable. Operating principle The EDL is activated automaticall
y, that is without any action
on the part of the driver.
It monitors the speeds of the driven wheels with the aid of the ABS sensors. Should only
one
drive wheel begin spinning on a slippery surface there will be an appreciable
difference in the speed of the driven wheels. The EDL function brakes the slipping wheel and the differential transmits a greate
r driving force to the other driven wheel.
This control process is also accompanied by noises. Overheating of the brakes The EDL switches off automatica
lly if unusually severe stresses exist in order to avoid
excessive heat generation in the disc brake on the wheel which is being braked. The vehicle can continue to be driven and has
the same characteristics as a vehicle not
fitted with EDL.
The EDL switches on again automatically
as soon as the brake has cooled down.
EDL Off-road* After switching on the Off-road mode
⇒page 170, EDL Off-road is activated.
EDL Off-road is matched in such a way that it assists the traction of the vehicle when driving on an unfirm ground. EDL is activated earlier in the Off-road mode than in the normal mode. The brake pres- sure builts up more quickly on the slipping
wheel, on one axle, as well as diagonally.
WARNING
•
Carefully depress the accelerator when
accelerating on uniformly slippery
road surfaces, such as ice and snow. Th
e driven wheels might still spin despite
the EDL and affect the stability of
the vehicle - risk of an accident!
•
You should always adapt your style of driving to the condition of road
surface and to the traffic situation even
when your vehicle is fitted with EDL.
The increased safety offered must not tempt you to take greater risks than otherwise - risk of an accident!
Note
•
If the ABS or ESP warning light comes on, this may also indicate a fault in the EDL.
Please have the vehicle inspected as soon
as possible by a specialist garage.
•
Changes to vehicle (e.g. on engine, on the brakes, on chassis or another combina-
tion of tyres and wheels) can influence the function of the EDL
⇒page 221, “Accesso-
ries, changes and replacement of parts”.
WARNING (continued)
sgg.6.book Page 164 Thursday, September 24, 2009 2:32 PM

Intelligent Technology
165
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Traction control system (TCS) The traction control system prevents
the driven wheels from spinning
when accelerating.General The TCS makes it much easier, and sometimes at
all possible, to start off, accelerate and
climb a steep hill when th
e conditions of the road
surface are unfavourable.
Operating principle The TCS switches on automatically when th
e engine is started and then conducts a
self-test. The system monitors the speeds of the driven wheels with the aid of the ABS sensors. If the wheels are spinning, the force transmitted to the road surface is auto- matically adapted by reducing the engine speed. The system operates at all speeds. The TCS operates in combination with the ABS
⇒page 167, “Antilock brake system
(ABS)”. The TCS will not function if a fault exists in the ABS system. The TCS warning light lights up in the instru
ment cluster when there is a fault on the
TCS
 ⇒page 34.
During an intervention of the system, the TCS warning light
 flashes quickly in the
instrument cluster
⇒page 34.
Switching off You can switch the TCS off and on again as yo
u wish. On vehicles fitted with ABS, you
can switch off the TCS by pressing the button
⇒fig. 155
, on vehicles fi
tted with ESP*,
you can switch off the TCS wi
th the aid of the button
⇒page 163, fig. 154
. The TCS
warning light
 flashes slowly in the instrument cluster if the system is switched off
⇒ page 34. The TCS should normally always
be switched on. It may be good practice in certain
exceptional cases, such as when you wish to
have wheel slip, to switch off the system.
Examples:•
when driving with snow chains
•
when driving in deep snow or on a loose surface
•
when it is necessary to rock a vehicle when it has become stuck.
Then you should switch on the TCS again. TCS Off-road* After switching on the Off-road mode
⇒page 170, TCS Off-road is activated.
TCS Off-road provides a more effective a
cceleration of the vehicle on an unfirm
ground, as it allows higher traction be
tween the slipping wheels and the ground.
The system operates when starting off or at low speeds.
WARNING
You should always adjust your style of driving to the conditions of the road surface and the traffic situation. The increased safety offered must not tempt you to take greater risks than otherwise - risk of an accident!
Note
•
All four wheels must be fitted with the same tyres in order to achieve problem-free
operation of the TCS. Differing rolling circumferences of the tyres can lead to an unde- sirable reduction in the engine output.•
Changes to vehicle (e.g. on engine, on the brakes, on chassis or another combina-
tion of tyres and wheels) can influence the function of the TCS
⇒page 221, “Accesso-
ries, changes and replacement of parts”.
Fig. 155 TCS switch
sgg.6.book Page 165 Thursday, September 24, 2009 2:32 PM

Intelligent Technology
167
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Caution
•
Never allow the brakes to rub by applying sl
ight pressure if you do not wish to brake
the vehicle. This causes the br
akes to overheat and can also result in a longer braking
distance and excessive wear.•
Before negotiating a steep downhill section, please reduce your speed, shift down
into the next lower gear (manual gearbox)
or select a lower driving stage (automatic
gearbox). This enables you to make full us
e of the braking power of the vehicle and
reduces the strain on the brakes. Any additional braking should be done intermittently, not continuously.
Note
The brake light flashes automatically in case
of an emergency braking at speeds greater
than 60 km/h or with the intervention of the ABS, which lasts longer than 1.5 seconds. After the speed was reduced below 10 km/h or the vehicle was stopped, the brake light stops flashing and the hazard warning light system switches on. The hazard warning light system is switched off automatically
after accelerating
or driving off again.
Brake boosterThe brake booster boosts the pressure which you generate with the brake pedal. The necessary pressure is only genera
ted when the engine is running.
WARNING
•
Never switch off the engine before the vehicle is stationary.
•
The brake booster only operates when
the engine is running. Greater phys-
ical effort for braking is required when en
gine is switched off. Because if you do
not stop as normal, this can cause an accident and severe injuries.
Antilock brake system (ABS)ABS prevents the wheels locking when braking.General The ABS contributes significantly to enhanc
ing the active safety of your vehicle.
Compared to a vehicle not fitted with the ABS brake system, you are able to retain optimal steering ability even during a full br
ake application on a slippery road surface
because the wheels do not lock up. You must not expect, however, that the br
aking distance will be shorter under all
circumstances as a result of the ABS. The braking distance for example on gravel and fresh snow, when you should anyway be driv
ing slowly and cautiously, will be longer.
Operating principle The brake pressure will be reduced on a wheel which is rotating at a speed which is too low for the speed of the vehicle and tending
to lock. This control
cycle is noticeable
from a
pulsating movement of the brake pedal
which is accomp
anied by noises.
This is consciously intended to provide the driver with the information that the wheels are tending to lock (ABS control range). You must always keep the brake pedal depressed to enable the ABS to optimally control the brake application in this braking range. Never interrupt the application of the brakes! ABS Off-road* After switching on the Off-road mode
⇒page 170, ABS Off-road is activated.
ABS Off-road increases the braking power of
the vehicle on an unfirm ground, as it
keeps the wheels blocked for a longer period
of time when the brake is applied while
sliding. The system is only available, if the front wheels are in the straight-ahead posi-tion. The system operates at speeds of up to 50 km/h.
WARNING
•
The ABS can also not overcome the physical
limits of your ve
hicle. Please do
not forget this, particularly when driving on icy or wet road surfaces. If the ABS is operating within the control range, adapt your speed immediately to the conditions of the road surface and the traffic situation. The increased safety
sgg.6.book Page 167 Thursday, September 24, 2009 2:32 PM

Intelligent Technology
168
offered by the ABS must not tempt you to take greater risks than otherwise - risk of an accident!•
The normal braking system is
still fully functional if there is an ABS fault.
Visit a specialist garage as quickly as poss
ible and adjust your style of driving to
take account of the ABS fault in the meantime since you will not know the extent of the fault and in how far the braking efficiency is affected.
Note
•
A warning light comes on if a fault occurs in the ABS system
 ⇒page 36.
•
Changes to vehicle (e.g. on engine, on th
e brakes, on chassis or another combina-
tion of tyres and wheels) can in
fluence the function of the ABS
⇒page 221, “Accesso-
ries, changes and replacement of parts”.Brake Assist*During a severe brake application (e.g. if a hazard exists), the Brake Assist increases the braking force and thus makes it possible to
rapidly produce the pressure required in
the brake system. The majority of drivers do apply the brakes
in good time in dangerous situations, but
do not depress the brake pedal with sufficient
pressure. Consequently, it is not possible
for the vehicle to achieve its maximum deceleration and the vehicle covers a greater distance than necessary. The Brake Assist is activated by the very quick operation of the brake pedal. In such cases, a much greater braking pressure exists
than during a normal
brake application.
This makes it possible, even with a relative
ly low resistance of the brake pedal, to
produce an adequate pressure in the brake system in the shortest possible time, which is required for maximum deceleration of th
e vehicle. You must apply the brake pedal
firmly and hold it in this position in order to achieve the shortest possible braking distance. The Brake Assist is able to help you achieve a shorter braking distance in emergency situations by rapidly producing the pressure required in the brake system. It fully exploits the attributes of the ABS. After you release the brake pedal, the function of the Brake Assist is automatically switched off
and the brakes operate in the normal way.
The Brake Assist is part of the ESP system. If a fault occurs in the ESP, the Brake Assist function is also not available.
Further information on the ESP
⇒page 163.
WARNING
•
The Brake Assist is also not able to overcome the physical limits of your
vehicle in terms of the braking distance required.•
Adapt your speed to the conditions of th
e road surface and to the traffic situ-
ation.•
The increased safety offered by the Brake Assist must not tempt you to take
a greater safety risk than otherwise.Uphill-Start off-Assist*The uphill-start off-assist makes it much easier to start off on steep hills. The system assists a start off by holding the brake pressure produced by the brake pedal actuation for approx. 2 seconds after releasing the brake pedal. The driver can therefore move his foot from the brake pedal to the accelerator pedal and start off on the slope, without having to actuate the handbrake. The brake pressure drops gradually the more you operate the accelerator pedal. If the vehicle does not start off within 2 seconds, it starts to roll back. The uphill-start off-assist is active in the ev
ent of a 3 % slope, if the vehicle door is
closed. It is always active on slopes when in forward or reverse start off. When driving downhill, it is inactive.Electromechanical power steeringThe power steering enables you to steer the vehicle with less physical force. With the electromechanical power steering, the steering assist is automatically adapted to the speed and to the steering angle. It is still possible to fully steer the vehicle if the power steering fails or if the engine is not running (vehicle being towed in). The only difference is that greater physical effort is required.
WARNING (continued)
sgg.6.book Page 168 Thursday, September 24, 2009 2:32 PM

Intelligent Technology
169
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
If there is a fault in the power steering, the warning light
 or  lights up in the instru-
ment cluster
⇒page 32.
WARNING
Contact your specialist
garage if the power steering is defective.
Tyre inflation pressu
re-control system*
The tyre inflation pressure-control system compares with the aid of the ABS sensors the speed and also the rolling circumference of the individual wheels. If the rolling circumference of a wheel is changed, the warning light
 lights up in the instrument
cluster
⇒page 35 and an audible signal sounds.
The rolling circumference of the tyre
can change if:•
the tyre inflation pressure is too low,
•
the structure of the tyre is damaged,
•
the vehicle is loaded on one side,
•
the wheels of an axle are loaded heavily (e.g. when towing a trailer or when driving
uphill or downhill),•
snow chains are mounted,
•
the temporary spare wheel is mounted,
•
one wheel per axle was changed.
Basic setting of tyre inflation pressure-control system After changing the tyre inflation pressures or after changing one or several wheels, the position of a wheel on the vehicle (e.g. ex
changing the wheels between the axles) or
when the warning light lights up while drivin
g, a basic setting of the system must be
carried out as follows.•
Inflate all tyres to the specified inflation pressure
⇒page 215.
•
Switch on the ignition.
•
Press button
⇒fig. 156
for more than 2 seconds. While pressing the button,
the warning light
 lights up. At the same time the memory of the system is erased
and the new calibration is started, which is confirmed with an audible signal and then the warning light
 goes out.
•
If the warning light
 does not go out after the basic
setting, there is a fault in the
system. Have the vehicle inspected by your nearest specialist garage. Warning light
 lights up
If the tyre inflation pressure of at least one
wheel is insufficiently inflated in comparison
to the stored basic va
lue, the warning light
 ⇒
lights up.
Warning light
 flashes
If the warning light flashes, there is a system fault. Have the vehicle inspected by your nearest specialist garage.
WARNING
•
When the warning light
 lights up, immediately reduce the speed and
avoid sudden steering and brake manoeuvr
es. Please stop the vehicle without
delay at the nearest possible stop and in
spect the tyres and their inflation pres-
sures.•
The driver is responsible for the correc
t tyre inflation pressures. For this
reason, the tyre inflation pressu
res must be checked regularly.
•
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light
 can be delayed or does not light up at all.
•
The tyre inflation pressure-control system does not take away the respon-
sability from the driver for the
correct tyre inflation pressure.
Fig. 156 Button for setting the tyre infla- tion pressure control value
 
sgg.6.book Page 169 Thursday, September 24, 2009 2:32 PM

Intelligent Technology
171
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
TCS Off-road
⇒page 165,
•
ABS Off-road
⇒page 167.
Switch on Off-road The Off-road mode is switched on by pressing the button
⇒page 170, fig. 158
. The
warning light in the button lights up. The wa
rning light lights up in the instrument
cluster if the system is switched on
 ⇒page 38.
Switch off Off-road The Off-road mode is switched off by repe
ated pressing of the button. The warning
light in the button goes out. When switching
off the ignition, the Off-road mode is also
switched off and can be switched on again, if necessary, after switching on the ignition. If the engine is switched off by accident an
d restarted within 30 seconds, the Off-road
mode remains switched on. All four wheels must be fitted with the same tyres in order to achieve proper operation of the Off-road mode. Differing rolling circum
ferences of the tyres can lead to an unde-
sirable reduction in the engine output.
WARNING
•
Always adjust your speed to suit weat
her, road and traffic conditions. The
increased safety must not tempt you to take a greater safety risk than otherwise - risk of accident!•
The Off-road equipment can also not overcome the physical limits of your
vehicle.•
The effect of the Off-road equipm
ent depends as well on the tyres.
•
The Off-road equipment
is not designed for the use on common roads.
Start-Off Assist*The Start-Off Assist enhances the driving comfort and can be used when starting off, in particular on a slope. When the vehicle is stationary, the Start-Off Assist is activated after switching it on using the button for the Off-road mode
⇒page 170, fig. 158
.
Operating principle When depressing the accelerator pedal fully, the engine speed required for the start- up procedure of the stationary vehicle is restricted. The overspeed trip unit is automat-ically deactivated after terminating the start-up procedure. As part of the Assist System, the accelerator pedal is adapted in its characteristics for an easier start-off on slippery and loose soil.Downhill Drive Support*Operating principle The Downhill Drive Support maintains a cons
tant speed on a steep downhill section
when driving forwards and backwards by
automatically intervening in the brake
system of all wheels. It prevents the wheels locking because the ABS remains active. The warning light
 in the information display of the instrument cluster indicates that
the Downhill Drive Support is available
⇒page 38.
The vehicle speed, which is maintained by the Assist System, is selected by the driver while driving on a downhill section as of the
moment the first intervention of the Assist
System is performed or else, while driving on a downhill section, the driver must control the vehicle speed until the Assist System intervenes for the first time. When the Assist System actively intervenes, this is indicated by the warning light flashing or by a pulsating movement of the brake pedal,
similar to the intervention of the ABS.
The Downhill Drive Support is available in the speed range of 2 km/h up to 30 km/h. If the gear is engaged and the clutch pedal is
not pressed, the lower limit of the idling
speed corresponds to the respective gear which is engaged. You can increase or reduce the speed, even when no gear is engaged, by operating the accelerator or brake pedal. Thus the function
is always interrupted and is reactivated
afterwards. The Downhill Drive Support is activated auto
matically if the following conditions are
met:•
the Off-road mode is switched on and the warning light
 lights up in the instru-
ment cluster,•
the engine of the vehicle is running and either the 1st, 2nd, 3rd gear, the reverse
gear or no gear is engaged,•
the speed is less than 30 km/h,
sgg.6.book Page 171 Thursday, September 24, 2009 2:32 PM

Taking care of your vehicle and cleaning the vehicle
198
Upholstery cloth and cloth trim on the d
oors, luggage compartment cover, headliner
etc. are best treated with special cleaning products, using if necessary a
dry foam
and
a soft sponge or brush. We recommend using a cleaning product from Škoda genuine accessories offered by your Škoda dealer.
Caution
Solvent-free cleaners attack th
e material and can damage it.
Fabric covers of elec
trically heated seats
Do
not clean
the seat covers moist as this may re
sult in damage to the seat heating
system. Clean such covers using specia
l agents, for example dry foam.
Natural leather Natural leather requires quite particular care and attention.Leather should be treated from time to time according the following guidelines depending on how much it is used.Normal cleaning– Clean soiled areas of the leather with
slightly moistened co
tton or woollen cloth.
Severe soiling– Clean severely soiled areas with a cloth
dipped in a mild soap
y solution (2 spoon-
fuls of natural soap to 1 litre of water).
– Ensure that the leather is not soaked through at any point and that no water gets
into the stitching of the seams.
– Dry off the leather with a soft, dry cloth.
Removing stains– Remove fresh stains which are
water-based
(e.g. coffee, tea, juices, blood etc.)
with an absorbent cloth or household pape
r or use the cleaner from the care set
for a stain which has already dried in.
– Remove fresh stains on a
fat base
(e.g. butter, mayonnaise, chocolate etc.) with an
absorbent cloth or household
cleaning paper or with the
cleaner from the care set
if the stain has not yet pe
netrated into the surface.
– Use a grease dissolver for
grease stains which have dried in
.
–Eliminate
special stains
(e.g. ball-point pens, felt pe
n, nail varnish, dispersion
paint, shoe cream etc.) with a special stain remover suitable for leather.
Leather care– Treat the leather every six months with th
e leather care product available from an
authorised Škoda Service Partner.
– Apply only a small amount of the care product.– Dry the leather off with a soft cloth. It is best to consult an authorised Škod
a Service Partner if you have any questions
regarding cleaning and care of the
leather interior in your vehicle.
Caution
•
You must on no account treat the leather wi
th solvents (e.g. gasoline, turpentine),
floor wax, shoe cream or such like.•
Avoid leaving your vehicle for lengthy period
s in bright sunlight in order to avoid
bleaching the leather. If you
leave your vehicle parked in the open for lengthy periods,
protect the leather from the direct ra
ys of the sun by covering it over.
•
Sharp-edged objects on items of clothing su
ch as zip fasteners, rivets, sharp-edged
belts may leave permanent scratches or signs of rubbing on the surface.
Note
•
Use a care cream with ligh
t blocker and impregnation
effect regularly and each
time after cleaning the leathe
r. The cream nourishes the leather, allows it to breathe
and keeps it supple and also provides mois
ture. It also creates surface protection.
sgg.6.book Page 198 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
204
Caution
Never open the bonnet using the locking lever - danger of causing damage.Working in the engine compartment Particular care is required when carrying out any work in the engine compartment!There is a risk of injuries, scalding, acci
dents and fire when working in the engine
compartment, e.g. inspecting and replenishing oil and other fluids. For this reason, it is essential to comply with the warning instructions stated below and with the general applicable rules of safe
ty. The engine compartment of your car
is a hazardous area
⇒
.
WARNING
•
Never open the bonnet if
you see that steam or coolant is flowing out of the
engine compartment - risk of scalding!
Wait long enough until the steam or
coolant has stopped escaping.•
Switch off the engine and pull out the ignition key.
•
Apply the handbrake firmly.
•
If your vehicle is fitted with a manual
gearbox, move the gearshift lever into
Neutral, or if it is fitted with automatic gearbox, move the selector lever into position P.•
Allow the engine to cool down.
•
Keep children clear of the engine compartment.
•
Never spill oil and other fluids over the hot engine. Such fluids (e.g. the anti-
freeze contained in the coolant) may ignite!•
Avoid short circuits in the electrical system - particularly on the battery.
•
Never place your hand into the radiator fan as long as the engine is still
warm. The fan might suddenly start running!•
Never open the cap of the coolant expans
ion bottle as long as the engine is
still warm. The cooling
system is pressurized!
•
Cover over the cap of the coolant expansion reservoir with a large cloth
when opening it as protection for your
face, hands and arms from hot steam or
hot coolant.•
Do not let objects, such as e.g cleaning cloth or tools lie in the engine
compartment.•
If you wish to work under the vehicl
e, you must secure the vehicle from
rolling away and support it with suitable supporting blocks: the car jack is not sufficient for this - risk of injury!•
In cases where it be necessary to carry out inspection work when the engine
is running there is an additional risk fr
om rotating parts (e.g. the V-ribbed belt,
alternator, radiator fan) and from the high-voltage ignition system. Please observe in addition the following:
− Never touch the electrical cabl
es of the ignition system.
− Absolutely avoid any jewellery, loose it
ems of clothing or long hair from
getting into the rotating parts of the
engine - Hazard! Therefore remove any
jewellery beforehand, tie up your hair and wear tight fitting clothing.
•
Please also comply with the warnin
g instructions st
ated below when
carrying out any essential work on the fu
el system or on th
e electrical system:
− Always separate the car battery from the electrical system. − Do not smoke. − Never carry out any work close to naked flames. − Always keep a working fire
extinguisher at hand.
Caution
When replenishing fluids in the engine, always
ensure that the fluids are on no account
mixed up. This may result in major oper
ating problems and also vehicle damage!
WARNING (continued)
sgg.6.book Page 204 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
209
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Radiator fan The radiator fan may switch on suddenly.The radiator fan is driven by an electric
motor and controlled according to the coolant
temperature. The radiator fan may continue running for up
to 10 minutes after the engine has been
switched off - even if the igni
tion is also off. It may also
switch on suddenly after a
certain time, if•
the coolant temperature has risen beca
use of an accumulation of heat or
•
the warm engine compartment is heated
up additionally by strong sunlight.
WARNING
You must therefore be aware when workin
g in the engine compartment that the
fan may switch on suddenly - risk of injury!Brake fluidInspecting the brake fluid levelThe brake fluid reservoir is lo
cated on the left of the engine compartment. The brake
fluid reservoir on right-hand steering models is positioned on the other side of the engine compartment. – Switch the engine off.
– Open the bonnet
⇒page 203.
– Inspect the brake fluid level in the reservoir
⇒fig. 174
. The level must be between
the “MIN” and “MAX” markings.
A slight drop in the fluid level results when driving due to normal wear-and-tear and automatic adjustment of the brak
e pads, and is perfectly normal.
There may be an indication of a leak in the brake system, however, if the fluid level drops significantly within a short time or if it drops below the “MIN” marking. If the brake fluid level is too low, this
is indicated by the warning light
⇒page 37, “Brake
system
” lighting up in the instru
ment cluster. In this case
stop immediately and do
not drive any further! Obtain
professional assistance.
WARNING
•
Read and observe the warning notes
⇒page 204, “Working in the engine
compartment” before working
in the engine compartment.
•
If the fluid level has dropped below
the MIN marking, do not drive any
further - risk of accident! Obtain professional assistance.Replacing brake fluidBrake fluid absorbs moisture. This causes
the fluid to absorb moisture from the
surrounding air over a period of time. Exce
ssive water in the brake fluid may be the
cause of corrosion in the brake system. The water content also lowers the boiling point of the brake fluid.
This is why brake fluid must be replaced every two years.
One may only use new genuine brake fluid from Škoda Auto. The specification for the brake fluid is “FMVSS 116 DOT 4”. We recommend that you have th
e brake fluid re
placed by an
authorised Škoda
Service Partner
as part of an Inspection Service.
WARNING
Using old brake fluid can result in severe stress on the brakes because of the formation of vapour bubbl
es in the brake system. This greatly impairs the
braking efficiency an
d thus also the safety of your vehicle.
Fig. 174 Engine compartment: Brake fluid reservoir
sgg.6.book Page 209 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
234
Fuse cover in engine compartment The fuse box in the engine compartment exists in two different versions. You can determine which version your vehicle is fitted with after removing the fuse cover at
the location of the fuses.
On some vehicles, the battery cover must be removed before removing the fuse cover ⇒ page 210.Removing fuse cover– Move the circlips
⇒fig. 193
as far as the stop, the symbol
 appears behind the
circlip and remove the cover.
Installing fuse cover– Position the fuse cover on the fuse box and
push the circlips as far as the stop -
the symbol
 is visible behind the circlip.
Caution
•
When unlocking and locking the fuse cover, it must be pressed on the sides to the
box, otherwise damage can occur to the locking mechanism.•
Carefully position the fuse
cover in the engine compartment. If the cover was not
correctly positioned, water can get into the
fuses and this results in a damage to the
vehicle!
Fuse assignment in engine compartment - version 1Certain electrical components are only stan
dard on certain vehicle model versions or
only suppliable as optional
equipment for certain models.
Fig. 193 Fuse cover in engine compart- ment
AA
AA
No.
Power consumer
Amperes
F1
Central control unit, right main headlight, right rear light unit
30
F2
Valves for ABS
20
F3
Not assigned
F4
Measuring circuit
5
F5
Horn
15
F6
Not assigned
F7
Valve for fuel dosing
15
F8
Not assigned
F9
Activated charcoal filter, ex
haust gas recirculation valve
10
F10
Leakage diagnosis pump
10
F11
Lambda probe upstream of catalytic converter, engine control unit
10
F12
Lambda probe downstream
of catalytic converter
10
F13
Control unit for automatic gearbox
15
Fig. 194 Schematic representation of fuse box in engine compartment - version 1
sgg.6.book Page 234 Thursday, September 24, 2009 2:32 PM