light SKODA YETI 2010 1.G / 5L Bolero Car Radio Manual
[x] Cancel search | Manufacturer: SKODA, Model Year: 2010, Model line: YETI, Model: SKODA YETI 2010 1.G / 5LPages: 24, PDF Size: 1.14 MB
Page 5 of 24
General information
3
Note
Damage within the meaning of the warranty
must not be the result of improper
handling of the system or from unprofessi
onal repair attempts. It is also essential
that there is no external damage.Device operationThe unit should only be used, if the traffic situation permits it. The volume settings must be selected in
such a way that audible signals from the
outside, e.g. a Martins horn from utility
vehicles (police cars, ambulances and fire
brigade), can be heard at all times.
WARNING
Please concentrate fully at
all times on your driving! As the driver you are
fully responsible for road safety. Only use the functions of the radio in such a way that you are always in full contro
l of your vehicle in all traffic situa-
tions!
Caution
•
Inserting a second CD while a CD is being ejected can destroy the CD drive in
the unit. Please note that the CD ejecti
on lasts a few seconds after pressing the
Eject key
. During this time the lock in fron
t of the CD case is open. It is essen-
tial that you wait until the CD has been fully ejected before you try to insert a new CD.•
Press the buttons and the keys of the uni
t gently in order to avoid damaging
them. Gentle pressure on the appropriate key is sufficient to operate the unit. Please note that the control buttons have
predetermined breaking points, in order
to reduce the risk of injury.•
Do not use any pointed or sharp-edged objects to operate the touch-screen.
Slight finger pressure sufficient to oper
ate the equipment. A text in the display,
which cannot be called up by pressing the
button, is therefore not available at that
time.
Using the displayCarefully handle the display because dent
s and scratches can occur through pres-
sure of the finger or contact with sharp objects. The display can be cleaned wi
th a soft cloth and finger marks can be wiped away
with pure alcohol.
Note
Do not use solvent such as turpentine or
petrol as they will corrode the display
surface.Anti-theft protectionAnti-theft codingYour radio is equipped with
a convenience coding. If the radio is being operated for
the first time, the safety code is not only st
ored in the radio but also in the vehicle.
After disconnecting and reconnecting the battery, first of all switch on the ignition and then the radio. If you wish to install the radio in another
vehicle, the safety code must be entered.
In this case, please do not hesitate to co
ntact an authorised Škoda Service Partner
or a Škoda importer. As the unit only functions afte
r entering the safety code, this practically excludes its
use after a theft - a contribution to increased anti-theft safety.
Note
The code is stored in the instrument cluste
r. This ensures that it is automatically
decoded (convenience coding). Manual
input of the code is normally not
necessary.
/
s3p4.a.book Page 3 Friday, March 13, 2009 3:04 PM
Page 9 of 24
Basic setting
7
- Button for calling up the automatic
play or for the radio text to fade
in .
- activates manual station finding.
The process of searching for and storing the radio stationsManual search – Turn the Set button in the
RADIO
main Setup or press on the func-
tion key . The scale of the selected frequency range is inserted in the frequency band in the lower part of the display.
– Briefly press the set button to terminate the manual frequency selec-
tion and to display once again the function keys.
Storing a radio station on a displayed station key – Continue to press one of the six station keys to displayed in
the
RADIO
main Setup until a signal tone sounds. The currently heard
radio station is then stored on this station key.
Deleting a radio station from the memory list –In the
RADIO
main Setup, press the function key to open the
memory list.
– Press the function key behind the station you wish to delete. – Confirm the following safety interrogation by pressing the function
key to finally remove the st
ation from the memory list.
If the currently heard radio station is already stored in the memory list, the memory space number is displayed behind the
description of the frequency range (
FM
or
AM
).
Use the
Setup Radio
main Setup, to determine which of the six station keys are to
be displayed in the main Setup
RADIO
.
Function SCANThe stations of a waveband
can be played briefly one after the other (for
ten seconds). – Press the set button , the radio searches automatically all available
stations of the current waveband.
– Alternatively, press the function key and press in the
opening pop-up window.
– During the current automatic play the function key will change from
to .
– Press the set button or function key again to end the auto-
matic play of the currently heard radio station.
RDS functionsSwitching radio text on and off –In the
RADIO
main Setup, press on the function key and on in the opening pop-up window. Instead of the six station
keys, the window for displaying the radio text is now opened in the lower half of the display.
– The window for displaying the radio text must fade out again to enable
the station keys to be displayed ag
ain. Briefly press on the display
window of the radio text.
– Alternatively, press the function key and the function key
shown as highlighted in
the opening pop-up window.
RDS (“
Radio
Data
System”) serves to transmit program identification and additional
services therefore also enabling automatic tracking of stations. In the event of sufficiently satisfactory reception, the suitable RDS radio stations will display the station name instead of the station frequency.
Extras
Scan
Radio TextMan.
A2
Man.
1 ...
6 ...
Memory
Delete
Delete
A2
Extras
Scan
Extras
Scan
A2
Scan
Extras
Radio Text
Extras
Radio Text
s3p4.a.book Page 7 Friday, March 13, 2009 3:04 PM
Page 13 of 24
Basic setting
11
Audio CD: Select track – Press on the function key , in order to display the title list of
the currently played audio CD. The cu
rrently played track is shown as
highlighted.
– Select one of the titles from the title
list by briefly pressing the function
key .
MP3 Data: Select track – Press on the function key , in order to display the title list with
the currently played title and, if necessary, to display the sub-folder contained in this folder. The currently played track is shown as high-lighted.
– Press to choose another title. If th
e title you are searching for is in
another folder, you must first of
all search the folder structure.
– Press on the display of a data folder to open it (in picture: ). – Press the function key to open
the appropriate higher priority
folder.
Repeat title – Press the function key . – Press in the opening pop-up window to automatically repeat the
current title at the end.
– If you press (Audio CD operation) or (MP3 operation) in
the opening pop-up window the titles of the current CD or the current folder are repeated automatically.
Note
You can also change titels in the
Setup MEDIA
by turning the set button .
•
If a data carrier in the internal
CD drive is ready to play, “
CD int.
” will be indi-
cated at the top left in the display.•
When playing MP3 data, the name of the artist, the album and the title of the
MP3 data will be displayed, if available, as
ID3 tag. The list an
d data name will be
displayed if there is no ID3 tag.•
Some audio CDs support “CD Text”. With these CDs the title name is displayed
instead of “
Tra c k
”.
General information for MP3 operationRequirements for the MP3 data and data carrier•
CD-ROM, CD-R, CD-RW with a capacity of 650 MB and 700 MB.
•
The CDs must correspond to the ISO 9660 Level 2 standard as well as the Joliet
data system (single and multi-session).•
Data names must be no lo
nger than 64 characters.
•
The list structure is restricted
to a depth of 8 list levels.
•
The name of the artist, the album and the title of the reproduced MP3 data can
be shown as ID3 tag, providing this information is available. The list and data name will be displayed if there is no ID3 tag.•
Playlists are supported.
•
WMA data (
Windows
Media
Audio) can also be played even if the copyright is
additionally protected by the DRM procedure (
Digital
Rights
Management). Such
WMA data is not su
pported by the unit.
Bit rate (data flow per time unit)•
The system supports MP3 data with bit rates of 32 to 320 KB/s as well as MP3
data with variable bit rates.•
The indicated playing time data with
variable bit rates is not reliable.
Information on how to use a CDCD to jump Uneven road surfaces and strong vibrations may cause the CD to jump.
Selection
Track ...
Selection
F1.1.1
Repeat
Title
CD
Folder
A2
s3p4.a.book Page 11 Friday, March 13, 2009 3:04 PM
Page 17 of 24
Basic setting
15
Traffic station set-upsCall up the
TIM Setup recording time
Setup by pressing the range selector
key and the function key . – Press on the left of the display on TIM recording time, in order to open
the
Time setting
Setup.
–In the
Time setting
Setup, briefly press on the arrow keys or on
the display, below the display of the hours or minutes, in order to gradually change the respective time unit down or up.
– Keep pressing the corresponding arro
w key, in order to continuously
change the time unit. Release the bu
tton if the desired value has been
reached.
– Press on the function key in or
der to take over the indicated TIM
recording time and to exit the Setup
Time setting
.
– In this way you can set both
desired TIM recording times.
– Activate or deactivate the desired TIM recording time by pressing the
function key . If the check-box is active
the accompanying
TIM recording time is activated.
The unit starts with the recording 90 minutes before the set start time and ends the recording 30 minutes afterwards.Setup MediaCall up the
Setup Media
Setup by pressing the range selector key
and the function key .Function keys in the Setup - Setup Media
- for playback of an external audio source.
- enables a wireless transfer of MP3 data from the Phone
preinstallation.
- according to the set-ups the title and performer
name or only the data and folder name
will be displayed for audio CDs with CD
texts and in the MP3 operation.
- plays all MP3 data one after the other
according to the sequence on the played medium, which are stored in the folders and sub-folders.
- the input sensitivity of the AUX-IN input for adjusting the play
function volume of a connected external
audio source can be adapted to other
audio sources in three steps. Press on the function key and select the desired input sensitivity in the openin
g pop-up window. If a MDI input is addi-
tionally installed, this setting also applies for the audio sources which are connected to this input.System set-upsCall up the
Setup System
Setup by pressing the range selector key
and the function key . Change the system language manually – Press on the function key and select the desired
language in the opening pop-up window. The system language is normally preset to the set language in the instrument cluster “ Automatic
”. If desired, another langua
ge can be selected for the
radio as described.
Resetting the factory settings on the unit – Press on the function key . – Confirm the following safety interrogation, the unit will be reset in the
as-delivered condition and all the stored data will be erased.
Rear lighting of the control buttons – Press on the function key .
SETUP
Traffic information
Active
SETUP
Media
Activate AUX inputActivate Bluetooth audio
Deactivate performers/Title namesScan/Mix/Repeat including sub-folderAUX Input level
AUX Input level
SETUP
System
System languageFa c t o r y s e t t i n g sILLUMINATION
s3p4.a.book Page 15 Friday, March 13, 2009 3:04 PM
Page 18 of 24
Basic setting
16
– On the unit, you can switch the rear
lighting of the control buttons
and on or off , if the ignition is switched on.
Display of the setting for the Climatronic unit* – Press on the function key . – You can switch the display of the Climatronic values on or off.Phone set-upsCall up the
Setup Phone
Setup by pressing the range selector key
and the function key . Updating phone data in the unit – Press on the function key
2) to update all entries in
the unit, the phone book of the mobile phone or the SIM card entered since the last connection. This
procedure can take a few minutes.
– Confirm the following safety interrogation. The “old” data in the
phone book can still be selected at the unit while the data is being updated.
– In this case, consult the instructio
n manual applicable
to your vehicle.
Deleting call lists
2)
– Press the function key . – If you confirm the following safety interrogation by pressing ,
the stored call numbers of all calls made and calls accepted in the unit will be deleted.
Modifying assigned shortcut keys – Press the function key to modify the assigned shortcut
keys.
– To change the assignment of a particular shortcut key, select the
respective shortcut key by pressing the key in the following Setup.
– Change the entry as described.Range selector key PHONEMain Setup PHONEConnect your mobile phone with th
e mobile phone program according
to the instruction manual applicable to your vehicle. – Press the selector key to call up the main Setup
PHONE
.
After the connection process, it will take a few minutes (depending on the size of the Phone book) until the phone book data
of the mobile phone connected to the
radio unit is available. Function keys in the main Setup PHONE - Take calls, establish or hold. After pr
essing the call list, the selected phone
numbers are displayed in the main Setup PHONE.
- End conversation or reject call.3) - establishes a connection to a an em
ergency number afte
r further confir-
mation. This function is also possible
without a connected mobile phone. It is,
however, necessary that a connection can be established via a mobile phone company.
2)Only valid for the universal Phone preinstallation GSM III.
A1
A2
2
1
CLIMATE POP-UPS
SETUP
Phone
Update phone bookDelete call lists
Delete
3)Only valid for the universal Phone preinstallation GSM III.
Speed dialPHONE
SOS
s3p4.a.book Page 16 Friday, March 13, 2009 3:04 PM