ESP SKODA YETI 2010 1.G / 5L Columbus Navigation System Manual

Range selector key NAV (Navigation)
48 Select a waypoint tour– In the menu
Waypoint navigation
press on the function key .
– Press on the function key in the pop-up window. – Choose a waypoint tour in the list
by pressing on the respective tour.
Drive a waypoint tour– In the menu
Waypoint navigation
press on the function key . The menu
Start
from which waypoint
will open. Starting and finishing points of the waypoint tour
are displayed at the top.
– Press the function key in the menu to drive the selected
tour in the opposite direction.
Stop route guidance– Press on the third function key at the bottom of the map display for information
about the distance to the closest waypoint and on the function key
in the pop-up window.
– Alternatively, press the range selector key and then press the function key
.
When driving Follow the information regarding turns as far as possible. Once you have come as close as 50 meters to a waypoint, the drive
recommendation will appear for the next
waypoint. If a waypoint has not been reached, you
must ignore it, otherwise the system will
continue to try and guide you
to this waypoint. The distance to the next waypoint and
the number of it according to the sequence
in the waypoint tour is indicated in the
third function key at the bottom of the map display. Press on this function key and choose in
the pop-up window to ignore the
waypoint to which the system wishes to guide you. Alternatively, press the range selector ke
y and then press on the function key
.
Press on the function key in the co
rresponding menu in order to approach
the last waypoint again.
While you are approaching a waypoint tour, press on the third function key at the bottom of the map display and on in the pop-up window in order to supplement the tour with further waypoints. For example, you can designate route marks and name them later
or store new detours on route. Alterna-
tively, call up this function by pressing
the range selector key and the function key
.
Memory
Edit waypoint tour
Start
Turn around waypoint tour
Stop route guidance
NAV
Stop
Next
NAV
Next
Previous
Save current position as waypoint
NAV
waypoint tour
s32k.a.book Page 48 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
49
Route guidanceStarting and stopping route guidanceSelect a travel destination or enter a tour and start the route guidance as described in the respective chapter. The unit will
switch over to the map display
⇒fig. 21
.
Route guidance in the map display– Press on the function key in the map display and on
⇒fig. 21

in the pop-up window to interrupt the route guidance.
– If you press the function keys and in the opening
pop-up window the route guidance wi
ll continue at the current position.
Route guidance in the main menu Navigation– Press the range selector key after route guidance has started to switch to the
main menu
Navigation
.
– Pressing the function key will interrupt the route guidance and “
Start
” will be
displayed again the function key.
– If you press on the function key the route guidance will continue at the
current position.
Select one of three alternative routes– If you have selected the function “
Suggest 3 alternative routes
” in the menu
Setup Navigation
, three selected routes to the chosen travel destination will be
calculated after the start of route guidance.
– If the calculation is terminated, three routes to the destination will be indicated in
the overview map. The three routes correspond to the selectable route options “Options”, “Fastest” and “Shortest” route.
– You are given further information to the respective route in the function keys on the
right. Route guidance will start on the sele
cted route as soon as you press one of
these function keys. The route options for the navigation are changed according to the selected route. You can change the route options at a later time.
After route guidance has started, the route becomes the first travel destination and is calculated according to the specified information. When switching to the map display, the map wi
ll always be opened in the last selected
type of display (2D, 3D, topographic).Receiving driving recommendations– Press the button on the unit, if you
wish to repeat the last audible driving
recommendation.
Fig. 21 3D map display during a

route guidance.
 ... /...
Stop route guidance
Navigation
Start route guidance
NAVStop
Start
Fig. 22 Optical driving recom- mendation in the split-screen of the map display.
A8
s32k.a.book Page 49 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
50– Press the range selector key in the
map display to insert the split-screen.
– Press the function key at the top left in the split-screen. – In the pop-up window press on to
display the direction arrows in the
split-screen
⇒page 49, fig. 22
.
– Press on in the pop-up window to
display an overview map in the split-
screen with the starting and finishing point.
Press briefly on this map to change its
type of display.
– Press the function key or the range selector key to close the split-screen. Route guidance tour plan When driving to a tour plan, route guidance
will start automatically to the next desti-
nation after reaching a stopover. If an exac
t stopover cannot be reached, it must be
deleted from the tour plan before route guidance continues to the next destination. If route guidance to the next destination has been started manually, only this destination will be approached and all further dest
inations of the tour
plan are ignored.
Note
•
If you have missed a turn-o
ff during route guidance an
d there is no other opportu-
nity to turn at that moment,
continue driving until the navi
gation system offers you an
alternative route.•
The quality of the messages transmitted by the unit depends on the available navi-
gation data and, during traffic problems, also
on the available traffic reports. The radio
stations broadcasting the traffic reports are responsible for the content and quality of the available traffic reports.Dynamic route guidance with TMC use Switching the dynamic navigation on or off– In the main menu
Navigation
press on the function key .
– In the map display, press on or on
⇒page 49, fig. 21
during
a route guidance and on in the pop-up window.
– In the menu
Route options
, press on the function key and select
the desired set-up by pressing yo
ur choice in the pop-up window.
– Press to confirm your input. Traffic problems received via TMC which affect the route are displayed in the map by means of a coloured symbol. Traffic proble
ms, which do not affect the route, are
displayed in the map by means of a grey
symbol. The direction in which a traffic
problem is found, is displayed by means of an arrow in the symbol. The duration of a traffic problem on the route is displayed
in the map by means of continuous PKW
(motor car) symbols
.
 Dynamic route
b Off
When the dynamic navigation is
switched off you will not be advised of traffic prob-
lems affecting your route duri
ng route guidance and you are not directed away from or
through the traffic problems. TMC traffic reports are updated automatically in the unit ⇒ page 51, “Requirements for a dynamic rout
e guidance” and displayed by pressing
the range selector key . If one of the announced traffi
c problems is on your route,
you can also switch on the
dynamic route guidance during the current
route guidance or block the route manually
⇒ page 52, “Manually blocking a stretch of the route”. Dynamic route
b Manual
If the dynamic navi
gation is set to
manual
and you are in route guidance mode you
can select to avoid the announced traffic problems on your route
⇒page 51,
“Requirements for a dynamic route guidance”. If the navigation system is alerted of a tr
affic problem on the calculated route, the
driver will be notified of this by means
of an audible message and information in a
pop-up window. The expected delay incurred in avoiding this traffic problem and the length of the alter- native route will be displayed. The expected time lost when driving through this traffic problem will also be displayed.•
Press to remain on the calculated route and to pass through the
traffic problem.•
Press on for an alternative route to
be calculated taking
into account the
announced traffic problem.
MAP
NAV symbol
Overview
O
MAP
Options
Navigation
 ... /...
Route options
 Dynamic route
OK
TMC
Current routeBypass
s32k.a.book Page 50 Friday, September 18, 2009 1:54 PM

Range selector key PHONE
57
Range selector key PHONEOverviewMain menu PHONE Individual functions in the menu TELEPHONE may depend on the equipment and th
e properties of the telephone.
Connect your mobile phone with the mobile
phone program according to the instruc-
tion manual applicable to your vehicle. – Press the range selector key to call up the main menu
PHONE
.
After the connection process, it will take a fe
w minutes until the phone book data of the
mobile phone connected to the radio unit is available. Function keys in the main menu PHONE - Take calls, establish or hold. After pr
essing the call
list, the selected phone
numbers are displayed in the main menu PHONE.
- End conversation or reject call.* - establishes a connection to a an em
ergency number afte
r further confirma-
tion. This function is also possible withou
t a connected mobile phone. It is, however,
necessary that a connection can be es
tablished via a mobile phone company.
and to - Shortcut keys; these can be allocated to, in
each case, one number.
- opens the number block for entering a call number. - opens a pop-up window for selecting a ca
ll list. Only call lists of missed, dialed
or accepted calls from the mobile phon
e preparation program can be displayed.
, - several calls can be accepted at once, -
switches off the microphone
during the conversation. Conv
ersations held inside the
vehicles cannot be heard by the other part
y when the microphone is switched off.
- opens the telephone book of the connected mobile phone for selecting a call
number.
Enter call numberEnter a number and select– Press on the function key in the main menu
PHONE
, in order to open the
number block for enteri
ng a call number.
– Press an inserted number key to accept
the corresponding number in the entry
line.
– You can delete the characters in the entry line from left to right by pressing the
function key .
– Press function key when the desired ca
ll number is indicated in the entry line.
The connection to the entered call number is established.
You can select the character “
+” instead of the first two digits (for example “
00”) when
entering a country code. For th
is step, hold the function key with the little triangle
“a” pressed until a pop-up window with the function keys and fades in. Press to accept the desired character into the entry li
ne - the pop-up window will close. If no
entries are entered, the pop-up window wi
ll close automatically after a few seconds.
The special keys “Stars” and “Rhombus”
have the same function as those on a
phone keypad. These characters are primarily needed when transmitting sound signals during a call.Telephone bookOpening the telephone book– Press on the function key in the bottom right in the main menu
PHONE
, in
order to open the phone book.
Call a call number fr
om the telephone book
– When in the menu
Phone book
move the sliding regulator in the scrollbar to the
bottom to view further stations.
– Press on the function key to select a phone book entry via a search mask.
PHONE
^SOSVoice mailbox
Preset 2
Preset 6
[:::]CallsExtras
Conference details
Switch off micro.
]
[:::]


00
+
*
#
]
Search
s32k.a.book Page 57 Friday, September 18, 2009 1:54 PM

Range selector key PHONE
58– Press in the left column on the display of a telephone book entry. The connection
to the
first
call number stored for this entry in the telephone book, will now be
established.
Display information relating to a telephone book entry– Press the function key on the right next to the telephone book entry you which
to display. The call numbers stored under this entry are displayed.
– If you press on the entry of a call number,
the connection to this call number will
be established.
Search for an entry in the telephone book– Press on the function key in the menu
Telephone book
to select a tele-
phone book entry via a search mask.
– Press a selectable character on the keypad
while in the search window to accept it
in the entry line.
– Press the function key to open the input window for digits and special charac-
ters. Press , to change again to the letter input mask.
– You can delete the characters in the entry line starting from the position of the
character insertion cursor from left to
right by pressing the function key .
– If you press on the button , the connection to the
first
call number is estab-
lished, by doing so an assigned name is displayed in the entry line in the telephone book.
The upper and lower case which is used when searching for a phone book entry, is
not

of importance. Editing field: Indicate specific characters Some letters are also marked with a small triangle “
a”. This indicates that specific char-
acters based on this letter can be selected. Continue to press down on the correspondin
g button with your finger until a pop-up
window with these specific characters fade
s in. After pressing the desired characters,
these characters are accepted in the entry li
ne and the pop-up window will close. If no
entries are entered, the pop-up window will close automatically after a few seconds.
Adapt a call numberOpen the display of a call number from the te
lephone book or a call list as described
in the corresponding chapter. – Press the arrow keys or to move the character entry cursor in the entry line. – Press on a character inserted into the ke
ypad to accept it
behind the character
entry cursor in the entry line.
– The connection to the disp
layed call number will be es
tablished as soon as you
press the function key .
Call listsOnly the dialed numbers which are missed
, selected and accepted by the mobile
phone preparation program
in the vehicle
are stored. The call lists stored in a mobile
phone will
not
be transferred to the vehicle.
– Press on the function key in the main menu
PHONE
.
– Select the call list from which you wish to
select a call number by pressing your
selection in the pop-up window. The corres
ponding list is displayed. Call numbers,
for which an entry exists in the telephone book, will be displayed together with the corresponding name.
You can use the function key , to display fu
rther information relating to the stored
call number.•
- shows a list of the non-accepted
calls from the mobile phone prep-
aration program.•
- shows a list of call numbers, with which the mobile phone prep-
aration program has attempted to establish a connection.•
- shows a list of calls accepted
by the mobile phone preparation
program. If the call number from a ca ll li st i s s to red in the te le phone book the s tored name in the telephone book is displayed instead of the call number. Incoming calls rejected with the function ke
y will be stored in the call list of the
accepted
calls.
0
Search;
A-Z


‚
b
Calls0
Missed callsDialled numbersReceived calls
^
s32k.a.book Page 58 Friday, September 18, 2009 1:54 PM

Range selector key PHONE
59
Call lists are always assigned to a user profile and are only displayed once the corre- sponding SIM card is connected agai
n with the mobile phone preparation.
Shortcut keysAt the time of the first connection with th
e SIM card of your mobile telephone all
shortcut keys have still not been assign
ed after the first call from the main menu
PHONE
.
Assigning free shortcut keys– If you press briefly on a non-assigned shortcut key the menu
Speed dial
will open
to enable a name and phone number to be entered.
– If you press the function key , an input mask will open to enable a name to
be assigned.
– If you press the function key a mask
will open to enable a number to be
assigned.
– Press the function key or to accept a call number for
these shortcut keys from
the correspo
nding list.
– Press the function key to erase all entries in all entry lines at once after confir-
mation with .
– If you have completed your entries in the Menu
Speed dial
, press the function key
.
– The entered name will be displayed in
the shortcut key of the main menu
PHONE
.
The call number entered will be assigned to a shortcut key.
Calling up a connection via the shortcut key–Briefly press an
assigned
shortcut key to establish th
e connection to the assigned
call number.
Modifying assigned shortcut keys– If the assignment of a shortcut key is
to be modified, keep
pressing the corre-
sponding shortcut key until the menu
Speed dial
has opened for modification.
The assignment of the shortcut keys remains stored in the unit and will only be displayed again when the corresponding SIM
card is connected again to the mobile
phone preparation program. Shortcut key The shortcut key has not yet been assigned a call number in the factory, as this depends upon the
corresponding mobile phone
company and country. The
name for this shortcut key has, however, been specified and cannot be changed. You should now store your mail box number so th
at you can quickly check your voice mail.
Editing field: further input possibilities - changes from upper case to lower case and vice versa. - opens the editing field for the entry of digits and special characters. The button
changes to . Press on , to change again to the letter editing field.
- space key for entering spaces. or - moves the cursor in the entry line to the left or right. - deletes characters in the entry line from
right to left, starting from the position of
the cursor.Phone conversationIf you have started the process of connecti
ng to a call number or accepted a call, the
main menu
PHONE
will change to the display
Phone conversation
.
Incoming phone call– An incoming phone call will be
displayed on the display by “
Incoming call
”
followed by the call number of the caller. If
the number of the caller is stored in the
telephone book, the name of the caller will be displayed instead of the call number.
– Press the function key to accept the call.– Press the function key to reject the call.
NameNumber
Call lists
Telephone book
<
OK
OK
Voice mailboxVoice mail box
:;
A-Z
A-Z
‚
b

^
s32k.a.book Page 59 Friday, September 18, 2009 1:54 PM

Range selector key PHONE
60 During a phone conversation– If you press the function key during
a phone conversation the current conver-
sation will be switched to “mute” (Display: “
Call being held
”). This means that the
connection remains intact while the audio transmission is interrupted.
– If you press the function key , agai
n the conversation can be continued.
– If you press the function key , during
a phone conversation, the connection to
the current call number will
be terminated and the unit
will change to the main
menu
PHONE
.
Carrying out an additional phone conversation– Press on the function key during a phone conversation to put the current
conversation on “hold” as described above.
– Select a new call number or
select a stored call number.
– If you are holding an additi
onal conversation, you can switch between both parties
(“alternate”).
“Call waiting” and changing be
tween two parties (Alternate)
– If you are called while holding a conversation, the number and the name of the
caller will appear below the current conver
sation on the touch-screen (Function:
“Call waiting”).
– Press on the function key in the line “
Incoming call
” to reject the second call.
– Press on the function key in the line “
Incoming call
” to accept the second call.
The connection to the first party will be
interrupted but not broken (Display: “
Call
being held
”).
– If you press the function key in the line “
Call being held
”, the conversation with
this party will continue and the other part
y will be “put on hold”. In this way you
can alternate between two parties.
– Press the function key , to break the co
nnection to the call
number displayed in
this line.
DTMF key tones A particular DTMF key tone is assigned to each each key of a phone. DTMF key tones are used, for example, for the input of a password via the phone or for choosing a colleague in a “Call center”. If a DTMF key tone has to be entered duri
ng a conversation, you
can open the keypad
field by pressing the function key at the bo
ttom left and follow the instructions (for
example: “For a private conversation with
one of our co-workers, please press ”).
You can store a longer DTMF key tone on your
mobile phone. If, during a conversation,
this DTMF key tone has to be entered, call
up the corresponding entry from the tele-
phone book as described. If you press in the input mask on the function key , the displayed character sequence in the entry line will be played as DTMF key tone sequence. Please note that in a DTMF key tone sequence the character “+” must not appear, as it interrupts the playing of a DTMF key tone.
^^
^
3
DTMF
s32k.a.book Page 60 Friday, September 18, 2009 1:54 PM