wheel bolts SKODA YETI 2010 1.G / 5L Owner's Manual

Wheels and Tyres219
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The date of manufacture
is also stated on the tyre wall (possibly only on the inside of
wheel):
DOT ... 45 09...
means, for example, that the tyre was ma nufactured in the 45th week of the year 2009.
Any spare wheel which differs from the tyres fitted to the vehicle (e.g. winter tyres or
low-profile tyres) should only be used for a short time in the event of a puncture and
when adopting an appropriately cautious styl e of driving. It should be replaced as
quickly as possible by a normal wheel.
WARNING

Only use those tyres or wheel rims which have been approved for your
model of Škoda Auto vehicle. Failure to observe this instruction will adversely
affect the road safety of your vehicle - risk of accident! Approval and licencing
of your vehicle on public roads may also become void as a result.

You must on no account drive at a high er speed than is permissible for your
tyres - risk of an accident resulting from tyre damage and loss of control over
your vehicle.

Tyres which are 6 years old or more should only be fitted in exceptional
cases and when adopting an approp riately cautious style of driving.

Never fit tyres which have already been used without having adequate
knowledge of their previous history. Tyre s age even if they have not been used
at all or only very little. A spare tyre must only be used in exceptional cases and
only then when adopting an appropriately cautious style of driving.

Do not, where possible, replace individu al tyres but at least replace them on
both wheels of a given axle at the same time. Always fit the tyres with the
deeper tread depth to the front wheels.For the sake of the environment
Old tyres must be disposed of in conf ormity with the appropriate regulations.
Note
It is not normally possible to fit wheels from other models of cars for technical reasons.
This may also apply in certain circumstances to the wheels of the same type of
vehicle.Wheel boltsWheels and wheel bolts are matched to each other in terms of design. Each time you
fit other wheels - e.g. light alloy wheels or wheels with winter tyres - you must therefore
also use the matching wheel bolts of the corr ect length and shape of spherical cap. This
is essential to ensure that the wheels are tightly fitted and that the brake system oper-
ates properly.
If you retrofit wheel trims (or have this done), please also ensure that an adequate
flow of air remains assured for cooling the brake system.
The authorised Škoda Service Partners are instructed in the technical possibilities
which exist regarding converting or retrofitting tyres, wheels and wheel trims.
WARNING

In case of incorrect treatment of the wheel bolts, the wheel can loosen when
the car is moving - risk of accident!

The wheel bolts must be clean and must turn easily. However, they must
never be treated with grease or oil.

If the wheel bolts are tightened to a too low tightening torque, the rim can
lossen when the car is moving - risk of accident! A tightening torque which is
too high can damage the bolts and threads and this can result in permanent
deformation of the contac t surfaces on the rims.Caution
The prescribed tightening torque of the wh eel bolts for steel and light alloy wheels is
120 Nm.
s2ug.6.book Page 219 Friday, April 9, 2010 2:24 PM

Breakdown assistance
224
head of the towing device*. The box is secured with a strap. The placement of the
vehicle tool kit can vary depe nding on the vehicle equipment.
The vehicle tool kit contains the following parts (depending on equipment fitted):
Wire clamps for removing the full wheel trims,

Wheel wrench*,

To w i n g e y e ,

Adapter for the wheel bolts lock*,

Replacement bulb set*
14),

To r x s c r e w d r i v e r.
Before placing the lifting jack back in its storage area, screw in the arm of the lifting jack
fully.
WARNING

The factory-supplied lifting jack is only intended for your model of vehicle.
On no account attempt to lift a heavier vehicle or other loads - risk of injury!

Ensure that the vehicle tool kit is safely attached in the luggage compart-
ment.Note
Ensure that the box is always secured with the strap.Tyre repair kit*The tyre repair kit is intended for the repair of minor tyre defects. The tyre repair kit
contains a compressor, inflation bottle, operating instructions and accessories.
The repair with the tyre repair kit is not at all intended to replace a permanent repair
on the tyre, this repair only serves to reach the next specialist garage. The repair can be
undertaken on the vehicle immediately. Please read the attached instructions care-
fully before the repair. The tyre repair kit is located in
a box in the luggage compartment  page 223, fig. 174.
The placement of the tyre repair kit can vary depending on the vehicle equipment.
Spare wheel*The spare wheel is stowed in the luggage compartment in the area below the variable
loading floor* and is secured with a special screw fig. 175 .
One should check the inflation pressure in the spare wheel (at best when generally
checking the tyre air pressures - see sign on the fuel filler flap page 216) to ensure
that the spare wheel is always ready to use.
Temporary spare wheel
A yellow warning label is displayed on the rim of the temporary spare wheel.
Please observe the following notes when driving with a temporary spare wheel:
The warning label must not be covered after installing the wheel.

Do not drive faster than 80 km/h with this spare wheel and pay particular attention
while driving. Avoid accelerating at full throttle, sharp braking and fast cornering.

The inflation pressure for this spare wheel is identical to the maximum inflation
pressure of the standard tyres.

Use this spare wheel only to reach the nearest specialist garage as it is not intended
for continuous use.
14)Depending on the vehicle equipment.
Fig. 175 Luggage compartment: Spare
wheel
s2ug.6.book Page 224 Friday, April 9, 2010 2:24 PM

Breakdown assistance225
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Changing a wheelPreliminary workThe following steps should be carried ou t before actually changing the wheel.
– If it is necessary to change a wheel, park the vehicle as far away as possible from
the traffic flow. The place you choose should be level.
–Have all the occupants get out. While changing a wheel, the occupants of the
vehicle should not stand on the road (e.g. behind a crash barrier).
– Apply the handbrake firmly.
–Engage 1st gear or if your vehicle is fitted with an automatic gearbox, position the
selector lever into position P .
– If a trailer is coupled, uncouple it.
–Take the vehicle tool kit  page 223 and the spare wheel*  page 224 out of the
luggage compartment.
WARNING

If you find yourself in flowing traffic switch on the hazard warning lights
system and place the warning triangle on the side of the road at the prescribed
distance from your vehicle while observing all national legal provisions. In this
way you are protecting not only yourself but also other road users.

Never start the engine with the vehicle si tting on the raised jack - danger of
suffering injury.Caution
If you have to change a wheel on a slope first block the opposite wheel with a stone or
similar object in order to secure the vehicle from unexpectedly rolling away.
Note
Comply with the national legal regulations.
Changing a wheelAlways change a wheel on a level surface as far as possible.
– Take off the full wheel trim* page 226 or the wheel trim cap page 227 or the
caps page 226.
– In the case of light alloy wheels remove the wheel trim cap page 227.
– First of all slacken the safety wheel bolt * and afterwards the other wheel bolts page 227.
– Jack up the vehicle until the wheel to be changed is clear of the ground
 page 227.
– Unscrew the wheel bolts and place them on a clean surface (cloth, paper etc.).
– Take off the wheel.
– Fit on the spare wheel and tighten the wheel bolts slightly.
– Lower the car.
– Tighten the wheel bolts firmly, alternatel y and diagonally using the wheel wrench
(crosswise) and last the safety wheel bolt* page 227.
– Mount the full wheel trim/wheel trim cap or the caps.
Note

All bolts must be clean and must turn easily.

You must never grease or oil the wheel bolts!

When fitting on unidirectiona l tyres, ensure that the tyres rotate in the correct
direction page 216.
Subsequent stepsAfter changing the wheel, you mu st perform the following steps.
– Stow and attach the replaced wheel in the spare wheel well using a special screw
 page 224, fig. 175.
– Stow the vehicle tool kit in the space provided.
– Check the tyre pressure on the spare wheel just mounted as soon as possible.
s2ug.6.book Page 225 Friday, April 9, 2010 2:24 PM

Breakdown assistance
226
– Have the tightening torque of the wheel bolts checked with a torque wrench as
soon as possible. Steel and light alloy wh eels must be tightened to a tightening
torque of 120 Nm .
– Change the damaged wheel or consult a specialist garage about possibilities for getting repairs done.
WARNING
It is necessary to observe the guidelines given on page 218 if the vehicle is
subsequently fitted with tyres which are different to those it was fitted with at
the works.
Note

If you find, when changing the wheel, that the wheel bolts are corroded and diffi-
cult to turn, the bolts must be replaced before checking the tightening torque.

Drive cautiously and only at a moderate speed to a workshop where the tightening
torque can be checked.
Full wheel trim*Pulling off– Hook the clamp found in the vehicle tool kit into the reinforced edge of the full
wheel trim.
– Push the wheel key through the clamp, support the wheel key at the tyre and pull off the wheel trim.Installing– First press the full wheel trim onto the wheel at the valve opening provided. Then
press the full wheel trim into the wheel in such a way that its entire circumference
locks correctly in place.
Caution

Use the pressure of your hand, do not knock on the full wheel trim! Heavy knocks
mainly on the points where the full wheel trim has not been inserted into the wheel,
can result in damage to the guide and centering elements of the full wheel trim.

Check for yourself that the safety wheel bolt is located in the hole in the area of the
valve before fitting the full wheel trim onto a steel wheel which is attached with a safety
wheel bolt  page 228.
Wheel bolts with caps*Pulling off– Push the plastic clip sufficie ntly far onto the cap until the inner catches of the clip
are positioned at the collar of the cap and detach the cap.Installing– Push the caps fully onto the wheel bolts.
The caps are located in the well of the luggage compartment.
Fig. 176 Removing the cap.
s2ug.6.book Page 226 Friday, April 9, 2010 2:24 PM

Breakdown assistance227
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Wheel trim caps*Pulling off– Carefully remove the wheel tr im cap using the wire clamp fig. 177 .Slackening and tightening wheel bolts
Slacken the wheel bolts befo re jacking up the vehicle.Slackening wheel bolts– Push the wheel wrench* fully onto the wheel bolt
15).
– Grasp the end of the wrench* and turn the bolt about one turn to the left
 fig. 178 .
Tightening wheel bolts– Push the wheel wrench* fully onto the wheel bolt
15).
– Grasp the end of the wrench* and turn the bolt to the right until it is tight.
WARNING
Slacken the wheel bolts only a little (about one turn) as long as the vehicle has
not yet been jacked up - risk of an accident!.
Note
Apply pressure carefully with your foot to the end of the wrench* if it proves difficult
to slacken the bolts. Hold tight on the vehicl e when doing this and ensure that you have
a steady position.Raise vehicle
You have to raise the vehicle with the lifting jack* in order to be able to
take off the wheel.Position the lifting jack* by selecting the ja cking point which is closest to the wheel to
be removed  fig. 179. The jacking point is located directly below the marking on the
plastic cover of the lower sill.
– Position the lifting jack* be low the jacking point and move it up until its claw is
positioned directly below the vertical web of the lower sill.
15)Use the appropriate adapter for slackening and tightening the safety wheel bolts page 228.
Fig. 177 Pulling off wheel trim cap on
light alloy wheelsFig. 178 Changing a wheel: Slackening
wheel bolts
Fig. 179 Changing a wheel: Jacking
points for positioning lifting jack
s2ug.6.book Page 227 Friday, April 9, 2010 2:24 PM

Breakdown assistance
228
– Align the lifting jack* so that its claw grasps the web of the lower sill at the height
of the marking on the plasti c cover and the base plate is resting flat with its
complete surface ag ainst firm ground.
– Turn the lifting jack* up further until the wheel is just clear of the ground.
Ground below the lifting jack which is soft and slippery can cause the vehicle to slip
off the jack. It is therefore always necessary to place the lifting jack* on a solid surface
or use a wide and stable base. Use a non-sl ip base (e.g. a rubber foot mat) if the
surface is smooth , such as cobbled stones, a tiled floor, etc.
WARNING

Always raise the vehicle with the doors closed - risk of injury!

Take suitable measures to prevent the base of the lifting jack from slipping
off - risk of injury!

Not positioning the lifting jack at the specified points can result in damage
to the vehicle. The jack can also slip off if it does not have sufficient grip - risk of
injury!

It is important to support the vehicle with suitable supporting blocks if you
wish to work under the lifted vehicle - risk of injury!
Securing wheels against being stolen*
You need a special adapter for sl ackening the safety wheel bolts.– Pull off the full wheel trim/cap from the wheel hub or cap from the safety wheel
bolt. – Insert the adapter with its toothed side into the inner toothing of the head of
the safety wheel bolt fig. 180 .
– Insert the wheel wrench fully onto the adapter .
– Slacken the wheel bolt, or tighten it firmly page 227.
– Reinstall the full wheel trim/wheel cap after removing the adapter or place the cap onto the safety wheel bolt.
– Have the tightening torque checked with a torque wrench as soon as possible.
Steel and light alloy wheels must be tightened to a tightening torque of 120 Nm.
The safety wheel bolts on vehicles fitted with them (one safety wheel bolt per wheel)
can only be loosened or tighten up by using the adapter provided.
It is meaningful to note th e code number hammered into the rear side of the adapter
or the rear side of the safety wheel bolts. You can obtain a replacement adapter from
an authorised Škoda Service Partner, if necessary, by quoting this number.
We recommend that you always carry the ad apter for the wheel bolts with you in the
vehicle. It should be stow ed in the vehicle tool kit.
Caution
Damage can occur to the adapter and safety wh eel bolt if the safety wheel bolt is tight-
ened up too much.
Note
The set of safety wheel bolts can be obta ined from an authorised Škoda Service
Par tner.Jump-startingInitial stepsYou can use the battery of another vehicle fo r jump-starting yours if the engine does
not start because the battery on your vehicle is flat. You will require jump-start cables
for this purpose.
AAAB
Fig. 180 Safety wheel bolt with adapter
ABAA
AB
s2ug.6.book Page 228 Friday, April 9, 2010 2:24 PM

Index263
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Power steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Button in the front passenger door and in the rear doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Buttons on the driver's door . . . . . . . . . . . . . . . . 47
Operational faults . . . . . . . . . . . . . . . . . . . . . . . . . 49
with central locking system . . . . . . . . . . . . . . . . . 49
RRadiator fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Rear armrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Rear fog light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Rear interior lighting . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Rear window Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Rear window heater . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Rear-view mirror Exterior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Interior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Recharge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Recommendation for changing gears . . . . . . . . . . . 20
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Synchronisation process . . . . . . . . . . . . . . . . . . . 45
Removing seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Replacing fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Replacing the wiper blades . . . . . . . . . . . . . . . . . . . . 65
Roof aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Roof luggage rack system . . . . . . . . . . . . . . . . . . . . . . 84 Running in the car . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
SSafe securing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Safety information
Engine compartment . . . . . . . . . . . . . . . . . . . . . 204
Safety wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Saving electrical energy . . . . . . . . . . . . . . . . . . . . . . . 174
Seat belt height adjuster . . . . . . . . . . . . . . . . . . . . . . 143
Seat belt warning light . . . . . . . . . . . . . . . . . . . . . . . . 143
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Belt tensioners . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Height adjustment . . . . . . . . . . . . . . . . . . . . . . . . 143
Safety information . . . . . . . . . . . . . . . . . . . . . . . . 142
taking off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Seat heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Selector lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Selector lever lock Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Selector lever positions . . . . . . . . . . . . . . . . . . . . . . . 121
Selector lever-emergency unlocking . . . . . . . . . . . 124
Service Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Service Interval Display . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting temperature Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Side lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Stability system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . 109
after fuel tank has run empty . . . . . . . . . . . . . 110
Diesel engines . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Petrol engines . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Steering active driver-steering recommendation . . . 166
Steering force assistance . . . . . . . . . . . . . . . . . . . . . 168
Storage compartments . . . . . . . . . . . . . . . . . . . . . . . . 88
Storage facilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Sun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Switching lights on and off . . . . . . . . . . . . . . . . . . . . . 53
Switching off the engine . . . . . . . . . . . . . . . . . . . . . 110
TTaking care of your vehicle . . . . . . . . . . . . . . . . . . . 193
TCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Temperature outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
the first 1 500 kilometres . . . . . . . . . . . . . . . . . . . . . 173
Thickness of brake pads Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Top Tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
s2ug.6.book Page 263 Friday, April 9, 2010 2:24 PM

Index
264
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Towing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
towing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Tow-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Tow-starting and towing vehicle
Automatic gearbox . . . . . . . . . . . . . . . . . . . . . . . 124
Traction control system . . . . . . . . . . . . . . . . . . . . . . 165
Traction control system (TCS) Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 General Maintenance . . . . . . . . . . . . . . . . . . . . 190
Transporting children . . . . . . . . . . . . . . . . . . . . . . . . 156
Tread depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Turn signal lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Two-way radio systems . . . . . . . . . . . . . . . . . . . . . . 128
Tyre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Tyre inflation pressure Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Tyre repair kit Tyre repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Tyres Winter tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220UUnderbody protection . . . . . . . . . . . . . . . . . . . . . . . 197
Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Uphill Start Assist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
VVanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Ventilation Auxiliary ventilation . . . . . . . . . . . . . . . . . . . . . . 105
Visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62WWarning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Warning symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Warning triangle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 with a high-pressure cleaner . . . . . . . . . . . . . . 194
Washing the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 193
Washing vehicle by hand . . . . . . . . . . . . . . . . . . . . . 194
Wax treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Wheel Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Spare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Wheel trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216, 226
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 de-icing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Windscreen Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Windscreen heater . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Windscreen washer nozzles . . . . . . . . . . . . . . . . . . . 63
Windscreen washer system Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Windshield washer fluid reservoir . . . . . . . . . . . . . 214
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Windshield washer system . . . . . . . . . . . . . . . . . . . 214
Windshield wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Winter tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Wiper blades Replacing the wiper blades . . . . . . . . . . . . . . . . . 65
XXenon headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
s2ug.6.book Page 264 Friday, April 9, 2010 2:24 PM