SMART FORTWO 2016 Repair Manual

Resetting the side windows
You must reset each side window if:
Rthe side window opens again slightly after
being closed fully.
Rthe side window can no longer be fully
opened or closed.
XClose all the doors.
XTurn the SmartKey to position2in the igni-
tion lock.
XPull the corresponding switch on the door
control panel until the side window is com- pletely closed (
Ypage 58).
XHold the switch for an additional second.
If the side window opens again slightly:
XImmediately pull the corresponding switch
on the door control panel until the side
window is completely closed (
Ypage 58).
XHold the switch for an additional second.
XIf the respective side window remains
closed after the button is released, then it
has been set correctly. If this is not the
case, repeat the steps above again.
Side windows59
>> Opening and closing.
Z

Problems with the side windows
GWARNING
If you close a side window again immediately after it has been blocked or reset, the side
window closes with increased or maximum force. The reversing feature is then not active.
Parts of the body could be trapped in the closing area in the process. This poses an increased
risk of injury or even fatal injury.
Make sure that no parts of the body are in the closing area. To stop the closing process,
release the switch or push the switch again to reopen the side window.
ProblemPossible causes/consequences and 0050Solutions
A side window cannot be
closed because it is
blocked by objects, e.g.
leaves in the window
guide.XRemove the objects.
XClose the side window.
A side window cannot be
closed and you cannot
see the cause.If a side window is obstructed during closing and reopens again
slightly:
XImmediately after the window blocks, pull the corresponding
switch again until the side window has closed.
The side window is closed with increased force.
If a side window is obstructed again during closing and reopens
again slightly:
XImmediately after the window blocks, pull the corresponding
switch again until the side window has closed.
The side window is closed without the anti-entrapment feature.
Operating the roller sunblind for the
panoramic roofThe roller sunblind shields the vehicle inte-
rior from sunlight.
XTo open: press the roller sunblind up by the
outer edge of recess 0043and slide it back-
wards.
XTo close: pull the roller sunblind forward
by the outer edge of recess 0043until it is
fully closed.
60Operating the roller sunblind for the panoramic roof
>> Opening and closing.

Useful information
i
This Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's Man- ual. Country-specific differences are pos-
sible. Bear in mind that your vehicle may
not feature all functions described here.
This also applies to safety-relevant sys-
tems and functions.
iRead the information on qualified spe-
cialist workshops: (Ypage 20).
Correcting the driver's seat position
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, steering wheel
or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, steering wheel or
mirrors and fasten your seat belt before
starting the engine.
Example
Observe the safety guidelines on seat adjust-
ment (Ypage 61).
XMake sure that seat 0087is adjusted prop-
erly.
Adjusting the seats (
Ypage 62)
When adjusting the seat, make sure that:
Ryou are as far away from the driver's air
bag as possible.
Ryou are sitting in a normal upright posi-
tion.
Ryou can fasten the seat belt properly.
Ryou have moved the backrest to an almost
vertical position.
Ryou can depress the pedals properly.
Observe the safety guidelines on steering
wheel adjustment (
Ypage 65).
XMake sure that steering wheel 0043is adjus-
ted properly.
Adjusting the steering wheel (
Ypage 65)
When adjusting the steering wheel, make
sure that:
Ryou can hold the steering wheel with your
arms slightly bent.
Ryou can move your legs freely.
Ryou can see all the displays in the
instrument cluster clearly.
Observe the safety guidelines for seat belts
(
Ypage 31).
XCheck whether you have fastened seat
belt 0044properly (Ypage 33).
The seat belt should:
Rfit snugly across your body
Rbe routed across the middle of your
shoulder
Rbe routed in your pelvic area across the
hip joints
XBefore starting off, adjust the rear-view
mirror and the exterior mirrors
(
Ypage 66) in such a way that you have a
good view of road and traffic conditions.
Seats
Important safety notes
GWARNING
Children could become trapped if they
adjust the seats, particularly when unat-
tended. There is a risk of injury.
Seats61
>> Seats, steering wheel and mirrors.
Z

When leaving the vehicle, always take the
SmartKey with you and lock the vehicle.
Never leave children unsupervised in the
vehicle.
GWARNING
If the driver's seat is not engaged, it could move unexpectedly while the vehicle is in
motion. This could cause you to lose control
of the vehicle. There is a risk of an acci-
dent.
Always make sure that the driver's seat is
engaged before starting the vehicle.
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, steering wheel
or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, steering wheel or
mirrors and fasten your seat belt before
starting the engine.
GWARNING
When you adjust a seat, you or other vehicle occupants could become trapped, e.g. on the
seat guide rail. There is a risk of injury.
Make sure when adjusting a seat that no one
has any body parts in the sweep of the seat.
GWARNING
The seat belt does not offer the intended
level of protection if you have not moved
the backrest to an almost vertical position.
When braking or in the event of an accident,
you could slide underneath the seat belt and
sustain abdomen or neck injuries, for
example. This poses an increased risk of
injury or even fatal injury.
Adjust the seat properly before beginning
your journey. Always ensure that the back-
rest is in an almost vertical position and
that the shoulder section of your seat belt
is routed across the center of your shoul-
der.
Observe the safety notes on "Airbags"
(
Ypage 34) and "Children in the vehicle"
(Ypage 42).
!To avoid damage to the seats and the seat
heating, observe the following informa-
tion:
Rkeep liquids from spilling on the seats.
If liquid is spilled on the seats, dry them
as soon as possible.
Rif the seat covers are damp or wet, do not
switch on the seat heating. The seat heat- ing should also not be used to dry the
seats.
Rclean the seat covers as recommended;
see the "Interior care" section.
Rdo not transport heavy loads on the seats.
Do not place sharp objects on the seat
cushions, e.g. knives, nails or tools. The seats should only be occupied by passen-
gers, if possible.
Rwhen the seat heating is in operation, do
not cover the seats with insulating mate-
rials, e.g. blankets, coats, bags, seat
covers, child seats or booster seats.
!Make sure that there are no objects in the
footwell under or behind the seats when
moving the seats back. There is a risk that
the seats and/or the objects could be dam-
aged.
Adjusting the seats
Illustration of variant 1
62Seats
>> Seats, steering wheel and mirrors.

Illustration of variant 2
Seat fore-and-aft adjustment
XRemove the seat belt from the belt loop by
opening the press stud.
XLift handle0087and slide the seat forwards
or rearwards.
XRelease lever 0087again.
Make sure that you hear the seat engage in
position.
Backrest angle
Variant 1
XRelieve the pressure on the backrest.
XTurn handwheel 0043forwards or backwards.
Variant 2
XRelieve the pressure on the backrest.
XPull release lever 0043.
The backrest is released.
XMove the backrest forwards or backwards.
XLet go of release lever 0043again.
Seat height1
XOnly variant 2: pull handle 0044up or push it
down repeatedly until the seat has reached the desired height.
Folding down the front-passenger seat
You can increase the size of the luggage com-
partment by folding the front-passenger seat
backrest forwards. Observe the loading guidelines (
Ypage 142)
and the notes in the "Child restraint system
on the front-passenger seat" section
(
Ypage 45).
Folding down
Illustration of variant 1
Illustration of variant 2
Variant 1:
XSlide the right-hand front seat to its rear-
most position.
XTurn handwheel 0043forward until the
desired seat backrest position is achieved
Variant 2:
XSlide the right-hand front seat to its rear-
most position.
XHold onto the backrest at the head restraint
with one hand.
XPull release lever 0043.
The backrest is released.
XFold the seat forwards.
1Only driver's seat, depending on equipment.
Seats63
>> Seats, steering wheel and mirrors.
Z

Folding back
GWARNING
If the seat backrest is not engaged, it may
fold forwards, e.g. during braking or in the event of an accident.
RAs a result, a backrest which is not
engaged would press you into the seat
belt. The seat belt can no longer offer the
intended level of protection and can even
cause injuries.
RThe backrest cannot restrain objects or
loads in the trunk.
There is an increased risk of injury.
Before every journey, make sure that the
backrest is engaged as described.
Variant 1:
XTurn handwheel 0043back until the desired
seat backrest position is achieved
Variant 2:
XPull release lever 0043.
The backrest is released.
XFold the backrest backwards.
XEnsure that the seat backrest is engaged
again.
Switching the seat heating on/off
Activating/deactivating
GWARNING
Repeatedly switching on the seat heating
can cause the seat cushion and backrest
pads to become very hot. The health of per- sons with limited temperature sensitivity
or a limited ability to react to excessively
high temperatures may be affected or they
may even suffer burn-like injuries. There
is a risk of injury.
Therefore, do not switch the seat heating on
repeatedly.
XTurn the SmartKey to position 2in the igni-
tion lock (Ypage 87).
XTo switch on: press button0044.
Indicator lamp 0043in the button lights up.
XTo switch off: press button0044.
Indicator lamp 0043in the button goes out.
iIf the battery voltage is too low, the seat
heating may switch off.
The seat heating switches off automati-
cally after about 10 minutes.
64Seats
>> Seats, steering wheel and mirrors.

Problems with the seat heating
ProblemPossible causes/consequences and0050Solutions
The seat heating has
switched off prema-
turely or cannot be
switched on.The on-board voltage is too low because too many electrical con-
sumers are switched on.
XSwitch off electrical consumers that you do not need, such as the
rear window defroster or interior lighting.
Once the battery is sufficiently charged, the seat heating will
switch back on automatically.
Steering wheel
Important safety notes
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, steering wheel
or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, steering wheel or
mirrors and fasten your seat belt before
starting the engine.
GWARNING
Children could injure themselves if they
adjust the steering wheel. There is a risk of
injury.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle.
Never leave children unsupervised in the
vehicle.
Adjusting the steering wheel
GWARNING
If the steering wheel is unlocked while the
vehicle is in motion, it could change posi-
tion unexpectedly. This could cause you to
lose control of the vehicle. There is a risk
of an accident.
Before starting off, make sure the steering wheel is locked. Never unlock the steering
wheel while the vehicle is in motion.
0043Release lever
0044To adjust the steering wheel height
XPush release lever 0043down completely.
The steering column is unlocked.
XSet desired steering wheel height 0044.
XPush release lever0043up completely.
The steering column is locked.
XCheck if the steering column is locked. To
do so, try and push the steering wheel up or down.
Steering wheel65
>> Seats, steering wheel and mirrors.
Z

Mirrors
Rear-view mirror
XAnti-glare mode:pivot anti-glare
switch 0043forwards or back.
Exterior mirrors
Important safety notes
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, steering wheel
or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, steering wheel or
mirrors and fasten your seat belt before
starting the engine.
GWARNING
The exterior mirrors reduce the size of the
image. Visible objects are actually closer
than they appear. This means that you could
misjudge the distance from road users
traveling behind, e.g. when changing lane.
There is a risk of an accident.
For this reason, always make sure of the
actual distance from the road users trav-
eling behind by glancing over your shoul-
der.
Adjusting the exterior mirrors manually
XTo adjust the mirror: move lever0043to the
right or left, up or down.
Adjusting the exterior mirrors electri-
cally
XTurn the SmartKey to position 1or 2in the
ignition (Ypage 87).
XTo select an exterior mirror: turn control
0087 to position 0047for the left exterior mir-
ror or to position 0048for the right exterior
mirror.
XTo adjust the mirror: move control0087to the
right or left, up or down.
The exterior mirrors can be heated by switch- ing on the rear window heating (
Ypage 82).
Exterior mirror pushed out of position
If an exterior mirror has been pushed for-
wards or backwards out of position, push the
exterior mirror into the correct position
manually.
66Mirrors
>> Seats, steering wheel and mirrors.

Useful information
i
This Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's Man- ual. Country-specific differences are pos-
sible. Bear in mind that your vehicle may
not feature all functions described here.
This also applies to safety-relevant sys-
tems and functions.
iRead the information on qualified spe-
cialist workshops: (Ypage 20).
Exterior lighting
General notes
For reasons of safety, smart recommends that
you drive with the lights switched on even
during the daytime. In some countries, oper-
ation of the headlamps varies due to legal
requirements and self-imposed obligations.
Exterior lighting settings
Operation
0043Combination switch control
0044Marking
0049003FLights off
004A 0060standing lamp, parking lamp,
license plate lighting
004B0057High-beam headlamps
004C0058Automatic headlamp mode, control-
led by the light sensor
004D0058Low-beam headlamps
006CMarking
006DCombination switch middle ring
00BE005AFront fog lamps
00BF005ERear fog lamp
If you hear a warning tone when you leave the
vehicle, the lights may still be switched on.
XTurn combination switch control 0043until
0058 or003F is at marking 0044.
When in the 0058position the exterior light-
ing switches off automatically if you:
Rswitch off the engine
Ropen the driver's door
Rlock the vehicle
Rdo not switch on the high-beam headlamps
Automatic headlamp mode
0058 is the favored light switch setting. The
light setting is automatically selected
according to the brightness of the ambient
light (exception: poor visibility due to
weather conditions such as fog, snow or
spray):
RWith the engine running: depending on the ambient light conditions, the daytime
driving lights or the parking and low-beam
headlamps are switched on or off automat-
ically
XTo switch on automatic headlamp mode: turn
combination switch control 0043until 0058
is at marking 0044.
GWARNING
When the light switch is set to 0058, the
low-beam headlamps may not be switched on
automatically if there is fog, snow or other causes of poor visibility due to the weather
Exterior lighting67
>> Lights and windshield wipers.
Z

conditions such as spray. There is a risk ofan accident.
In such situations, turn the light switch to
0058.
The automatic headlamp feature is only an
aid. The driver is responsible for the vehi-
cle's lighting at all times.
Low-beam headlamps
XTo switch on: turn combination switch con-
trol 0043until 0058is at marking 0044.
The 0058 indicator lamp in the instrument
cluster lights up.
Parking lamps
XTo switch on: turn combination switch con-
trol 0043until 0060is at marking 0044.
Canada only: the standing lamps are only
switched on when the engine is switched off.
When the engine is running, the low-beam
headlamps are switched on.
Front fog lamps
Only vehicles with front foglamps have the
"Foglamps" function.
XTo switch on: make sure that the standing
lamps or low-beam headlamps are switched on.
XTurn combination switch middle ring 006D
until marking 006Cis at 005A.
The 005A indicator lamp in the instrument
cluster lights up.
After releasing, the middle ring returns
automatically back to the neutral position.
XTo switch off: turn combination switch
middle ring 006Duntil marking 006Cis at
005A.
The 005A indicator lamp in the instrument
cluster goes out.
After releasing, the middle ring returns
automatically back to the neutral position.
iIf you switch off the engine (only in the
0058 position) or turn off the lights, the
foglamps are also switched off.
Rear fog lamp
XTo switch on: make sure that the fog lamps
or low-beam headlamps are switched on.
XTurn combination switch middle ring 006D
until marking 006Cis at 005E.
The 005E indicator lamp in the instrument
cluster lights up.
After releasing, the middle ring returns
automatically back to the neutral position.
XTo switch off: turn combination switch
middle ring 006Duntil marking 006Cis at
005E.
The 005E indicator lamp in the instrument
cluster goes out.
After releasing, the middle ring returns
automatically back to the neutral position.
iIf you switch off the engine (only in the
0058 position) or turn off the lights, the
rear foglamps are also switched off.
Switching on the turn signals
XStart the engine.
XTo indicate briefly: press the combination
switch briefly to the pressure point in the direction of arrow 0043(right turn signal)
or 0044 (left turn signal).
The corresponding turn signal flashes
three times.
XTo indicate: press the combination switch
beyond the pressure point in the direction
of arrow 0043(right turn signal) or 0044(left
turn signal).
68Exterior lighting
>> Lights and windshield wipers.