warning SMART FORTWO COUPE 2008 Owners Manual

What to do if ...
>> Practical hints.
247
The subsequent self check of the safety
systems yields the following results:
Scenario 1:
The SRS indicator lamp goes out after a
maximum of 4 seconds:
No malfunction detected. The supplemental
restraint system is operational.
Scenario 2:
The SRS indicator lamp goes out after a maxi

mum of 4 seconds for approximately 1 second,
then it comes on again and stays on:
There is a malfunction in the supplemental
restraint systems. The air bags or Emer

gency Tensioning Devices could deploy un

expectedly or fail to deploy in an accident.
>Do not sit on the passenger seat; this ap

plies particularly to children.
>Have the system checked at an authorized
smart center.
!
If the SRS indicator lamp comes on while
driving, have the system checked at an autho

rized smart center immediately.
It is possible that the air bag and the emer

gency tensioning device could be activated
unintentionally or will not function in the event
of an accident.Turn signal indicator lamp(s)
Flash(es):
• when the ignition is switched on:
• the corresponding turn signal is switched
on.
• the hazard warning flasher is switched on.
>If the turn signal indicator lamp(s) do(es)
not illuminate, have the turn signal indica

tor lamp(s) checked at an authorized smart
center.

What to do if ...
>> Practical hints.
249 Acoustic warning signals
Door warning
A warning signal sounds if the door is opened
while a gear is engaged with the engine run

ning and neither the brake nor accelerator
pedals are depressed.
In addition a warning signal sounds if you
open the driver’s door with the key in the
starter switch position 0 to remind you not to
leave the key in the vehicle.Anti
theft warning system*
Once the anti
theft warning system has been
armed, a visual and audible alarm is triggered
when someone opens
• a door or the tailgate,
• when the vehicle's interior is entered,
• if there is motion inside the vehicle,
• if the vehicle is raised.
The alarm is also triggered if the passenger
door is unlocked with the key (

page 250).
To cancel the alarm:
>Insert the key in the starter switch.
>Turn starter switch in Position 1
(

page 91).
or
>Press button
©
or
ª
on the key.Seat belt reminder system
If seat belts are not fastened when the engine
is started, a warning chime will sound, for de

tails see seat belt telltale (

page 245).
Mechanical/acoustic brake pad indicator
The vehicle is equipped with a mechanical/
acoustic brake pad indicator. If you can hear
a continuous noise from the front axle when
braking, have the brake pads checked at an
authorized smart center.

Unlocking/locking manually
250
>> Practical hints.
Unlocking the vehicleYou can unlock the driver’s door and the fuel
filler flap by unlocking the driver’s door using
the key. The lock cylinder is fitted with a cap.
>Press button
©
on the key.
The anti
theft warning system* is disarmed.
i
If the transmitter battery in the key is
discharged, the anti
theft warning system*
can no longer be disarmed with button
©
on
the key. For replacing the transmitter battery
(

page 253).
Unlocking the vehicle with the key and opening
a door or the tailgate will trigger the anti

theft warning system* (

page 77).
To cancel the alarm:
>Insert the key in the starter switch.
>Turn starter switch in Position 1
(

page 91).
1
Cap
2
Lock cylinder
>Remove cap
1 from lock cylinder
2.
>Unlock the driver’s door.
The driver’s door and the fuel filler flap are
unlocked.
i
To unlock the vehicle centrally press the
central unlocking switch in the upper center
console (

page 38).
Locking the vehicleIf you can no longer lock the vehicle using the
remote control and you do not have a spare
transmitter battery at hand, please proceed
as follows:
>Open the driver's door.
>Press the central locking switch
(

page 84).
The indicator lamp on central locking
switch
1 comes on, when the starter switch
is in position 1.
The indicator lamp on central locking
switch1 flashes, when the starter switch is
in Position 0.
>Remove the key from the starter switch,
take it with you, and close all doors.
The vehicle is now locked and the anti
theft
warning system* is armed. P72.10
3348
31

Replacing transmitter battery
252
>> Practical hints.
NotesThe remote control's transmitter battery is
almost spent when the turn signals flash
rapidly nine times in a row when locking the
vehicle.i
If you do not replace the transmitter
battery, after about 100 more times you will no
longer be able to lock or unlock the vehicle
using the remote control.>Replace the transmitter battery.
or
>Have the transmitter battery replaced at an
smart center.
Batteries contain materials that can harm the
environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries for
recycling.
G
Warning!
Batteries contain poisonous and corro

sive substances. Therefore keep the
batteries out of reach of children.
If a battery is swallowed, seek medical
help immediately.

Replacing bulbs
254
>> Practical hints.
About replacing bulbsSafe vehicle operation depends on proper
exterior lighting and signaling. It is therefore
essential that all bulbs and lamp assemblies
are in good working order at all times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. Contact an autho

rized smart center for headlamp adjustment.
i
If the headlamps or front fog lamps* are
fogged up on the inside as a result of high
humidity, driving the vehicle a distance with
the lights on should clear up the fogging.
G
Warning!
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before
changing a bulb. Otherwise you could be
burned if you touch them.
Keep bulbs out of the reach of children.
Halogen lamps contain pressurized gas.
Abulb can explode if you:
• touch or move it when hot
•drop the bulb
• scratch the bulb
Wear eye and hand protection.

Replacing bulbs
260
>> Practical hints. High mounted brake lamp
1
Retaining screws
2
High mounted brake lamp
3
Bulb socket
>Removing: Unscrew retaining screws
1.
>Remove high mounted brake lamp
2.
>Detach the electrical connector from bulb
socket
3.
>Turn the bulb counterclockwise and pull it
out of its socket.
>Installing: Install in the reverse order.License plate lamps
1
License plate lamp unit jacking point>Use a suitable tool to loosen the corre

sponding license plate lamp unit at jacking
point
1.
>Carefully unclip the license plate lamp unit.
2
Electrical connectors
3
Bulb
>Detach electrical connectors
2.
>Remove bulb
3.
>Insert the new bulb.
>Attach electrical connectors
2.
>Fit the license plate lamp unit on the right
and press gently on the left.
The license plate lamp unit must audibly
engage. P82.10
4838
31
G
Warning!
High outside temperature, stop
and
go
traffic, driving on long uphill grades, or
driving at high engine speed may increa

se the temperature in the engine com

partment. Therefore the area around the
air slots in the rear apron may be hot. Let
the engine cool off before touching this
area to prevent burns.
P82.10
4999
31

Replacing wiper blades
262
>> Practical hints.
About replacing wiper blades
!
Hold on to the wiper when folding the wiper
arm back. If released, the force of the impact
from the windshield wiper tensioning spring
could crack the windshield.
Do not allow the wiper arms to contact the
windshield glass without a wiper blade
inserted.
We recommend that you have this work carried
out at an authorized smart center.
To ensure proper visibility,
• it is vital that you have wiper blades that
are in perfect shape.
• clean the wiper blades regularly with a
cleaning agent.
• remove any tough dirt stains with a sponge
or brush.
Windshield wiper blades!
Do not pull on the wiper blade inserts.
They could tear.
>Remove the key from the starter switch.
>Fold the wiper arm away from the windshield
until it snaps into place.
1
Retaining springs
2
Detaching wiper blade
G
Warning!
For safety reasons, switch off the wipers
and remove the key from the starter
switch before replacing a wiper blade.
The windshield wipers could otherwise be
set in motion and cause injury.G
Warning!
Wiper blades are components that are
subject to wear and tear. Replace the
wiper blades at least twice a year, pref

erably in the spring and fall. Otherwise
the windows will not be properly wiped. As
a result, you may not be able to observe
surrounding traffic conditions and could
cause an accident.

Flat tire
>> Practical hints.
265 Preparing the vehicle
Upon experiencing any type of problem with
the vehicle's tires, switch on the hazard warn

ing flasher, carefully slow down and exit the
roadway in a cautious manner.
>Park the vehicle at a safe distance from
moving traffic on a hard, flat surface when
possible
.
>Set the parking brake.
>Turn the steering wheel so that the front
wheels are in a straight ahead position.
>Move the gear selector lever to park
positionP.
>Turn off the engine.
>Remove the key from the starter switch and
take the key with you.i
Open door only when conditions are safe to
do so.
>Have any passenger exit the vehicle at a
safe distance from the roadway.
Using the tire repair kitThe tire repair kit can be used to seal punc

tures of up to approximately 0.16 in (4 mm) on
the tire tread.
The tire repair kit enables you to drive on the
sealed tire to the nearest authorized smart
center.
>You should have the sealed tire replaced at
an authorized smart center.
G
Warning!
Take care not to allow the contents of the
tire sealant to come in contact with hair,
eyes or clothing. The tire sealant is
harmful if inhaled, swallowed or absorbed
through the skin it may causes skin, eye
and respiratory irritation. Wear gloves
while using this product if they are avail

able.
Any contact with eyes or skin should be
flushed immediately with plenty of water.
If clothing comes in contact with the tire
sealant, change clothing as soon as pos

sible.
In case of allergic reaction or rash,
consult a physician immediately.

Flat tire
266
>> Practical hints.
Notes• Small tire punctures, particularly those in
the tread, can be sealed with the tire seal

ant.
• The tire sealant can be used in ambient
temperatures from
4°F (
20°C) to +104°F
(+40°C).
• Do not remove any foreign objects such as
nails or screws that have penetrated the
tire.
• Do not use the tire sealant if the tire has
been damaged by being driven when insuf

ficiently inflated (e.g. bumps, cuts, cracks
etc. on the tire).
• Allow escaped tire sealant to dry, then peel
it off.• Immediately wash all painted surfaces that
came into contact with the tire sealant using
a damp cloth.
• Avoid skin and eye contact with the tire
sealant.
• Do not swallow the tire sealant.
• Allow the tire sealant that is inside the
damaged tire to dry and dispose of together
with the tire.
• Do not use the tire sealant after the expira

tion date has elapsed (see top of container).
Instead, have it replaced at an authorized
smart center.
G
Warning!
The tire sealant is a limited repair
device. The tire sealant cannot be used
for cuts or punctures larger than
approximately 0.16 in (4 mm) and tire
damage caused by driving with extremely
low tire inflation pressure, or on a flat
tire, or a damaged wheel.
Do not drive the vehicle under such
circumstances.
If you are unsure of the condition of the
tire or have any question whatsover
about its suitability for driving contact
the nearest smart center for assistance
or call Roadside Assistance.

Flat tire
>> Practical hints.
267
>Take the tire repair kit from the passen

ger’s footwell (

page 234).
>Open the tire repair kit lid.
1
Flange
2
Pressure gauge
3
Deflate button
4
Filler hose with stopper
5
Operating instructions label
6
Electrical plug
7
Electric air pump switch
8
Sticker
9
Tire sealant container>Attach sticker
8 where it will be easily
seen by the driver on the instrument
cluster.
>Pull electrical plug6
and filler hose
4
out
of the housing.
>Unscrew the lid of flange
1.
>Unscrew the lid of tire sealant container
9.
Make sure that you do not damage the
aluminum seal.
>Screw tire sealant container
9 onto
flange
1.
Make sure that the container is threaded
correctly onto the flange. This punctures
the aluminum seal of the tire sealant con

tainer.
G
Warning!
Please review the instructions below for
using the tire repair kit. If you are not
confident that you can competently follow
the instructions for using this kit, do not
use the kit, but instead call for Roadside
Assistance.G
Warning!
Keep the tire sealant out of reach of
children. If swallowed, rinse mouth imme

diately with plenty of water and drink
plenty of water.
Do not induce vomiting!
Consult a physician immediately.
Keep away from open flame, heat source
or sparks. Do not smoke.
G
Warning!
Follow safety instructions on the electric
air pump label.