Park SMART FORTWO COUPE 2008 Workshop Manual

Replacing bulbs
>> Practical hints.
255 Overview bulbs
Front lamps Rear lamps
P82.10
4837
31
Lamp
Type
1
Turn signal lamp
PY 21 W
2
Low beam headlamp
H7 (55W)
3
Parking and side

marker lamp
WY 5 W
4
Front fog lamp*
H11
5
High beam headlamp
H7 (55W)
6
Side turn signal lamp
WY 5 W
Lamp
Type
7
High
mounted brake
lamp
W16W
8
Brake, tail, turn
signal, and
sidemarker lamp
12 V 21/5 W
9
Reflector


a
Back
up lamp
12 V 21 W
b
License plate lamp
C5W

Replacing bulbs
256
>> Practical hints. Notes on bulb replacement
• Only use bulbs of the same type and with the
specified watt rating.
• Switch the lights off before replacing a bulb
to prevent short circuits.
• Always use a clean lint
free cloth when
handling bulbs.
• Your hands should be dry and free of oil and
grease.
• Avoid touching the glass of the bulb with
bare fingers.
• If the newly installed bulb does not come on,
contact an authorized smart center.
• Have the bulbs for the front fog lamps*
replaced at an authorized smart center.
Replacing bulbs for front lampsBefore you start to replace a bulb for a front
lamp, do the following first:
>Turn the exterior lamp switch to
positionM (

page 101).
>Switch off the ignition.
>Open the service flap (

page 176)
Left headlamp, (right headlamp in reverse)
1
Bulb socket for parking, and side marker
lamp
2
Bulb socket for turn signal lamp
3
Low beam headlamp cover
4
High beam headlamp coverParking and sidemarker lamp bulb
>Removing:
Driver side: Turn bulb socket
1 toward the
outside.
Passenger side: Turn bulb socket1 toward
the outside.
>Pull bulb socket
1 out of the headlamp
housing.
>Pull the bulb out of bulb socket
1.
> Installing: Insert the new bulb into bulb
socket
1.
>Insert bulb socket
1 into the headlamp
housing.
>Driver side: Turn bulb socket
1 toward the
inside.
Passenger side: Turn bulb socket1 toward
the inside. P82.10
4836
31

Flat tire
>> Practical hints.
265 Preparing the vehicle
Upon experiencing any type of problem with
the vehicle's tires, switch on the hazard warn

ing flasher, carefully slow down and exit the
roadway in a cautious manner.
>Park the vehicle at a safe distance from
moving traffic on a hard, flat surface when
possible
.
>Set the parking brake.
>Turn the steering wheel so that the front
wheels are in a straight ahead position.
>Move the gear selector lever to park
positionP.
>Turn off the engine.
>Remove the key from the starter switch and
take the key with you.i
Open door only when conditions are safe to
do so.
>Have any passenger exit the vehicle at a
safe distance from the roadway.
Using the tire repair kitThe tire repair kit can be used to seal punc

tures of up to approximately 0.16 in (4 mm) on
the tire tread.
The tire repair kit enables you to drive on the
sealed tire to the nearest authorized smart
center.
>You should have the sealed tire replaced at
an authorized smart center.
G
Warning!
Take care not to allow the contents of the
tire sealant to come in contact with hair,
eyes or clothing. The tire sealant is
harmful if inhaled, swallowed or absorbed
through the skin it may causes skin, eye
and respiratory irritation. Wear gloves
while using this product if they are avail

able.
Any contact with eyes or skin should be
flushed immediately with plenty of water.
If clothing comes in contact with the tire
sealant, change clothing as soon as pos

sible.
In case of allergic reaction or rash,
consult a physician immediately.

Flat tire
>> Practical hints.
267
>Take the tire repair kit from the passen

ger’s footwell (

page 234).
>Open the tire repair kit lid.
1
Flange
2
Pressure gauge
3
Deflate button
4
Filler hose with stopper
5
Operating instructions label
6
Electrical plug
7
Electric air pump switch
8
Sticker
9
Tire sealant container>Attach sticker
8 where it will be easily
seen by the driver on the instrument
cluster.
>Pull electrical plug6
and filler hose
4
out
of the housing.
>Unscrew the lid of flange
1.
>Unscrew the lid of tire sealant container
9.
Make sure that you do not damage the
aluminum seal.
>Screw tire sealant container
9 onto
flange
1.
Make sure that the container is threaded
correctly onto the flange. This punctures
the aluminum seal of the tire sealant con

tainer.
G
Warning!
Please review the instructions below for
using the tire repair kit. If you are not
confident that you can competently follow
the instructions for using this kit, do not
use the kit, but instead call for Roadside
Assistance.G
Warning!
Keep the tire sealant out of reach of
children. If swallowed, rinse mouth imme

diately with plenty of water and drink
plenty of water.
Do not induce vomiting!
Consult a physician immediately.
Keep away from open flame, heat source
or sparks. Do not smoke.
G
Warning!
Follow safety instructions on the electric
air pump label.

Flat tire
>> Practical hints.
269
>Unscrew the end of filler hose
4 from the
tire valve.
>Plug filler hose
4 with the stopper.
>Tire sealant container
9 remains screwed
onto flange
1. The filler hose may still be
hot. Please exercise appropriate caution.
>Place the tire repair kit securely in the
vehicle.
>Drive off immediately.
The tire sealant will distribute itself evenly
inside the tire.>After driving for about 1.8 miles (3 km) or
ten minutes, take all of the appropriate
safety precautions and then take the tire
repair kit from the vehicle.
>Screw the end of filler hose
4
on to the tire
valve.
>Check the tire inflation pressure using
pressure gauge
2.>If the tire inflation pressure is at least
20 psi (1.3 bar), inflate or deflate the tire
to correct tire inflation pressure (see Tire
and Loading Information placard located on
the driver’s door B
pillar.
>To increase the tire inflation pressure:
Switch on the electric air pump.
>To decrease the tire inflation pressure:
Press on deflate button
3. Recheck the
tire inflation pressure with the electric
air pump's pressure gauge.
>After checking the tire inflation pressure,
unscrew the end of filler hose4
from the
tire valve.
>Plug filler hose
4 with the stopper.
>Place the tire repair kit securely in the
vehicle.
>Screw the valve cap onto the tire valve.
G
Warning!
Do not exceed vehicle speed of
50 mph (80 km/h). A tire sealant repair is
not designed to operate at higher
speeds.
The sticker must be attached on the
instrument cluster where it will be easily
seen by the driver.
Vehicle handling characteristics of a tire
sealant repaired tire may change. Adapt
your driving accordingly.
G
Warning!
If tire inflation pressure has fallen below
20 psi (1.3 bar) do not continue to drive
the vehicle.
Park your vehicle safely away from the
roadway and contact the nearest smart
center or call Roadside Assistance.
Have the damaged tire replaced.

Battery
>> Practical hints.
271 About the battery
Your vehicle’s battery is located in the
passenger’s footwell below the footrest
(
page 273).
The battery should always be sufficiently
charged in order to achieve its rated service
life. Refer to Maintenance Booklet for battery
maintenance intervals.
If you use your vehicle mostly for short

distance trips, you will need to have the
battery charge checked more frequently.
When replacing the battery, always use
batteries approved by smart.
Battery: 12 volts and 42 Amps
If you do not intend to operate your vehicle
for an extended period of time, consult an
authorized smart center about steps you need
to observe.Batteries contain materials that can harm the
environment if disposed of improperly. Recy

cling of batteries is the preferred method of
disposal. Many states require sellers of bat

teries to accept old batteries for recycling.
G
Warning!
Observe all safety instructions and
precautions when handling automotive
batteries.
Risk of explosion.Fire, open flames and smoking
are prohibited when handling
batteries. Avoid creating
sparks.Battery acid is caustic. Do not
allow it to come into contact with
the skin, eyes or clothing.
Wear suitable protective cloth

ing, especially gloves, apron
and faceguard.
Wear eye protection.
Rinse any acid spills imme

diately with clean water. Contact
a physician if necessary.Keep children away.Follow the instructions in this
Operator’s Manual.

Battery
272
>> Practical hints.
G
Warning!
Failure to follow these instructions can
result in severe injury or death.
Observe all safety instructions and
precautions when handling automotive
batteries (

page 271).
Never lean over batteries while connect

ing, you might get injured.
Battery fluid contains sulfuric acid. Do
not allow this fluid to come in contact with
eyes, skin or clothing. In case it does,
immediately flush affected area with
water and seek medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
G
Warning!
Do not place any metal objects on a bat

tery. You could otherwise cause a short
circuit and the battery’s highly flammable
chemicals could ignite.
Never allow any metal object to contact
both battery terminals or the positive
terminal and the vehicle body at the same
time. This might short circuit the battery
and ignite the highly flammable and ex

plosive hydrogen gas generated by the
battery, causing serious personal injury.
G
Warning!
Keep flames or sparks away from battery,
avoid improper connection of jumper
cables, smoking, etc.
• When disconnecting the battery, always
disconnect the negative terminal first,
followed by positive terminal.
• When connecting the battery, always
connect the positive terminal first, fol

lowed by the negative terminal.
• Do not loosen or disconnect the
battery terminal clips while the engine
is running or the key is in the starter
switch.

Battery
>> Practical hints.
273
!
Never loosen or detach battery terminal
clamps while the engine is running or the key
is in the starter switch. Otherwise the alter

nator and other electronic components could
be severely damaged.
Have the battery checked regularly at an
authorized smart center.
Refer to Maintenance Booklet for maintenance
intervals or contact an authorized smart cen

ter for further information.
!
Never invert the terminal connections!
Disconnecting, removing, charg

ing, reinstalling and reconnecting
the batteryDisconnecting the battery
>Set the parking brake.
>Move the gear selector lever to park
positionP.
>Turn off all electrical accessories.
>Turn off the engine.
>Open the passenger door.
>Move the passenger seat to the rear as far
as possible.>Unscrew the carpet holder in the
passenger’s footwell (

page 234).
>Lift the carpet.
1
Footrest
2
Fastening screw
>Unscrew fastening screw
2 counterclock

wise.
>Pull footrest
1 sideways out of the vehicle.
>Read and observe safety instructions and
precautions (
page 271).
G
Warning!
With a disconnected battery
• you will no longer be able to turn the
key in the starter switch.
• the gear selector lever will remain
locked in positionP.P54.10
2831
31

Battery
274
>> Practical hints.
3
Negative terminal
4
Positive terminal cover
5
Battery mount
!
Always disconnect the battery in the order
described below. Otherwise the vehicle’s
electronics can be damaged.>Disconnect the battery negative lead from
negative terminal
3.
Make sure the negative lead does not come
into contact with the positive lead.
>Remove cover
4 from the positive terminal.
>Disconnect the battery positive lead.
Removing the battery
>Unscrew battery mount
5.
>Remove the battery support and bracket.
>Pull out the ventilation hose from the bat

tery (depending on battery arrangement in
your vehicle model, the ventilation hose is
located either on the left or right side of the
battery).
>Remove the battery.Charging the battery
P54.10
2832
31
G
Warning!
Avoid creating sparks when charging the
battery as escaping gases are flammable.
Keep open flames away from the battery
and do not smoke.
Do not touch the battery terminal with
metal objects and do not remove the bat

tery charger's terminal clamps until the
battery charger has been switched off
and no further gas is being discharged by
the batteries.
Only charge the battery in a well
ventilated area.
There is a risk of acid burns during the
charging procedure due to the gases
which escape from the battery. Do not
lean over the battery when it is being
charged.

Jump starting>> Practical hints.
277 Jump start assistance
Your vehicle’s battery is located in the
passenger’s footwell below the footrest
(
page 273).
For jump starting, use the terminals of the
battery, keeping the leads connected.
>Make sure the two vehicles do not touch.
>Set the parking brake.
>Move the gear selector lever to park
positionP.
>Turn off all electrical accessories.
>Turn off the engine.>Get access to the battery in the passen

ger’s footwell (

page 273).
>Remove the positive terminal cover.
1
Positive terminal of discharged battery
2
Negative terminal of charged battery
3
Positive terminal of charged battery
4
Negative terminal of discharged battery
!
Never invert the terminal connections!>Connect positive terminals
1
and
3 with
the jumper cable.
Clamp the cable to positive terminal3 of
the charged battery first.
>Start the engine of the vehicle with the
charged battery and run at idle speed.
>Connect negative terminals
2 and
4 with
the jumper cable.
Clamp the cable to negative terminal2 of
the charged battery first.
>Start the engine of the disabled vehicle.
You can now turn on the electrical accesso

ries. Do not switch on the headlamps under
any circumstances.
>Remove the jumper cables first from
negative terminals
2 and
4 and then from
positive terminals
1 and
3.
You can now switch on the headlamps.
>Have the battery checked at the nearest
authorized smart center.
G
Warning!
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and
precautions when handling automotive
batteries (

page 271).P54.10
2749
31